FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable

40x Female-Female Cable 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Dupont female connectors on both ends
- Compatible with 2.54mm male connectors
- High quality and good working conditions
- Easy to install and use

It has an ON / OFF switch that will cut off power when you don't need it.
USB to Micro USB On/Off Switch Arduino Charger Cable features:
- Black color
- Length: 150cm
- Maximum current 1A

You can easily control any device over the Internet through your phone, computer, etc.
The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point).
In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters).
In STA mode, the relay module is connected to the access point (router) that supplies the network.
Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers).
You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off.

SIM800L GPRS GSM SIM Board Quadband features:
Package includes:
- SIM800L module,
- 2x pin headers,
- Spring antenna,
- 3G PCB antenna - 15cm cable.
- Supported SIM format: Micro SIM.

A multiplexer of this type actually only acts as a switch 16 to a 1.
The 4 digital pins are used to set high or low, (binary Y0-Y15) to determine which input pin is connected to pin "Z".
The control input S0-S3 is set to low "logic level 0", the signal C0 is connected to the output Z. Multiplexer 16 Channels CD74HC4067 MUX/DEMUX features:
- Based on chip CD74HC4067
- Analog signal input: Y0-Y15, 16 channels
- Analog signal output: Z pin
- Digital input, channel control: S0-S3
- Module size: approx. 4 x 1.8cm
- Package includes:
* 1 x CD74HC4067 MUX connection module
* 2 x row of soldering pins

Characteristic: - AVR 5V / 3.3V microcontrollers - change the programming voltage through jumper JP1
- LED status indicators - Transmission speed: 5kB / s
- Fuse protector against possible damage to the USB port
- Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux
- Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦
- Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny15 € ¦
- CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦
- AT90S2313 series, AT90S2323, AT90S2343, AT90S4414, AT90S4433 € ¦

Ideal to connect TTL RS232 devices to your PC through the USB port. RS232 USB to Serial TTL Adapter Module - USB to Serial PL2303HX PL2303 features:
> - Compatible PL2303 controller
- 5 pins: 3.3V, 5.0V, TxR, RxD, GND
- Heat shrinkable insulating cover
- Led data transmission indicators
- 2.5A self-recovery protector fuse
- Supported OS: Win ME, Win2003, Win XP, Vista, Win 7
- Weight: 40 gr. (approx.)

6-pin/10-pin Kanda DIL adapter features:
- Connector for Usbasp Programmer AVR Atmega8 Atmega128

3.3V/5V I2C logic level converter module with soldering pins.
Ideal to connect a device that works at 3.3V to one that works with 5V.
It works with digital signals (high and low levels).
Logic Level Converter 3.3 / 5V I2C IIC features:
- Voltage: 3.3V/5V
- Measures: 1.5x 1 cm

Ideal for connecting RS485 devices to your PC through the USB port. USB to RS485 USB to 485 Max485 Converter features:
- CH340 controller
- Supported OS: Win XP, Vista, Win 7.8, OS, Linux
- Work with Modbus, Profibus
- USB 2.0 specification with 6Mbps of maximum speed
- Measures: 60x 18x 14 mm

Ideal for connecting TTL RS232 devices to your PC through the USB port. PL2303HX PL2303 USB to UART TTL Cable Module RS232 Converter 4 Pin features:
- Compatible controller PL2303HXA
- 4 pins: 5.0V (red), TxR (green), RxD (white), GND (black)
- 2.5A self-recovery protective fuse
- Supported OS: Win8, Win10, WinME, Win2003, Win XP, Vista, Win 7 The 64-bit Prolific drivers provided by Microsoft through Windows Update will not work with most adapters and will therefore generate the generic "Code 10" error.

Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features:
- Controller CP2102
- 5 pins: 3.3v, 5.0v, TxR, RxD, GND
- Standard USB type to male and 5 pin TTL connector
- 3 Status LEDs: Power, RX and TX
- USB 2.0 specification with 12Mbps maximum speed

FTDI FT232RL USB-UART Converter - Mini USB features:
- Serial Converter USB-TTL 3.3V - 5V
- LED indicator of Tx, Rx, power.
- Communication: TTL COM Virtual RS232 RX / TX Transceiver
- Voltage: 3.3V or 5V - per bridge
- Pins: DTR, RX, TX, VCC, CTS, GND
- Protections: Electronic fuse up to 500mA.
- Size: 46 x 19 mm. Step 2.54mm.
- Connection: Mini USB
- Driver: Windows 7 / 8/10 Linux / Mac / Android
- USB TO UART solution with mini USB connector
- FT232RL original on board
- Compatible with Mac, Linux, Android, WinCE, Windows 7/8 / 8.1 / 10 ...
- 3 power mode: 5V output, 3.3V output or powered by the destination board (3.3V-5V)
- 3 LEDs: TXD LED, RXD LED, POWER LED
- Functional pins

This module equipped with a PCF8591 converter has a low current power supply and includes 8 bit CMOS data acquisition devices.
Your converter has four analog inputs, one analog output and one I2C serial bus interface.
It is supplied in the voltage range 2.5V-6V, analog voltage between the negative potential VSS and positive VDD. The control and data signals are transmitted on the two-wire I2C bi-directional bus to the transformed series.
The intensity of the ambient light can be converted into a digital signal thanks to its integrated photoresistor.
It allows access to eight PCF8591 converters on the same I2C bus without additional equipment. Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V features:
- Supply voltage (between VSS and VDD): 2.5-6VDC