Sensor Module Moisture Earth Water Soil The module has two outputs: analog A0 and digital D0 Digital output D0 - signal 0 appears or 1 depending on the threshold setting The threshold is set with the potentiometer The sensor can be used for example: Automatic watering for potted plants With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants Characteristic: Operation: 3.3V -5V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - indicator digital switching output - PCB measurements: 3 x 1.5 cm - Probe measurements: 6 x 3 cm Code S0021 Available Price €1.95
Adapter Battery 9V 6F22 Jack Connector DC Ideal to power your Arduino board through the power input.Adapter Battery 9V 6F22 Jack Connector DC features:- Cable 7cm long- Battery connector 9V, 6F22- Male connector DC 5.5 / 2.5 Code PP011 Available Price €0.99
150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car A high-performance voltage regulator-riser 12V laptop power supply car accumulator150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car features:- Input voltage: 10V-32V- Output voltage: 12-35V (adjustable)- Output current: 6A maximum- Input current: 10A maximum- Output power: 100W of natural cooling (MAX), plus 150W (MAX) fan- Conversion efficiency: up to 94% (2.5 A 16V Input Output 19V when measured - only as a reference)- Wiring: seamless terminal- Operating temperature: industrial grade (-40 „ƒ to 85 „ƒ) (room temperature exceeds 40 degrees, use of lower power, or add fan)- Current without load: 25 mA typical Code A0006 Available Price €4.99
Protoboard Breadboard 400 points for Arduino It can be used to work with AVR, ARM, PIC microcontrollers, Arduino modules and to work with self-designed prototypes. Arduino Protoboard Breadboard 400 points features: -400 Connections -Linkable with other Plates -Base with adhesive to attach it to the work surface -Measures 82x55x8 mm Code PB002 Available Price €1.90
Resistor 10K Ohm 5% 0,25W 1/4W Resistor 10K Ohm 5% 0,25W 1/4W features:-10K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0021 Available Price €0.08
Plastic Housing DB9 DB15 Cover Connector RS232 D-SUB Plastic Housing DB9 DB15 Cover Connector RS232 D-SUB features: - Plastic housing for DB9 DB15 connector Code K0084 Available Price €0.98
3.5mm Mini Jack Chassis Panel Mount Earphones Stereo Front Connector 3.5mm Mini Jack Chassis Panel Mount Earphones Stereo Front Connector features: - Quantity: 1 unit- 3.5mm jacks for mounting on flat surfaces- 3-pole connectors suitable for use with headphones and other stereo audio equipment- Termination method: welding- Color: gold / black Code K0082 Available Price €1.39
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development Mini ESP8266 ESP12E CH340 WiFi Development NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC It works as a standard WiFi 802.11 b / g / n 2.4 GHz Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features: - Compatible with Arduino, programming with the Arduino IDE - Power supply voltage: 5V - LOGICAL LEVELS: 3.3V - 11 input / output pins - 1 ADC (input: 0-3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and power management units Integrated Code W0061 Available Price €4.79
USB to RS485 USB to 485 Max485 Converter Ideal for connecting RS485 devices to your PC through the USB port. USB to RS485 USB to 485 Max485 Converter features: - CH340 controller- Supported OS: Win XP, Vista, Win 7.8, OS, Linux- Work with Modbus, Profibus- USB 2.0 specification with 6Mbps of maximum speed- Measures: 60x 18x 14 mm Code C0003 Available Price €2.69
FTDI FT232RL USB-UART Converter - Mini USB FTDI FT232RL USB-UART Converter - Mini USB features: - Serial Converter USB-TTL 3.3V - 5V - LED indicator of Tx, Rx, power. - Communication: TTL COM Virtual RS232 RX / TX Transceiver - Voltage: 3.3V or 5V - per bridge - Pins: DTR, RX, TX, VCC, CTS, GND - Protections: Electronic fuse up to 500mA. - Size: 46 x 19 mm. Step 2.54mm. - Connection: Mini USB - Driver: Windows 7 / 8/10 Linux / Mac / Android - USB TO UART solution with mini USB connector - FT232RL original on board - Compatible with Mac, Linux, Android, WinCE, Windows 7/8 / 8.1 / 10 ... - 3 power mode: 5V output, 3.3V output or powered by the destination board (3.3V-5V) - 3 LEDs: TXD LED, RXD LED, POWER LED - Functional pins Code C0014 Available Price €12.95
TTL Level Converter 5V - 3.3V IO LJ245A TTL level conversion module 5V 3.3V IO Single Interchange Compatible I2C SPI.Use of high-speed dual-level IT supply level translator chip design. TTL Level Converter 5V - 3.3V IO LJ245A features: - Main chip: Octal bus transceiver and change from 3.3-V to 5-V with outputs of 3 states LJ245A of Texas Instrument- VCCA power supply voltage: 4.5 - 5.5 VDC- VCCB power supply voltage: 2.7 - 3.6 VDC- Low level input voltage V (IL): 0.8 V- High-level input voltage V (IH): 2 V- Low level output current I (OL): 12 - 24 mA- High level output current I (OH): -24 - -12 mA- 8 channels allow the conversion of the IO communication level- Channel levels A and B are controlled by VCCA and VCCB Code C0017 Available Price €3.95
6-pin/10-pin Kanda DIL adapter 6-pin/10-pin Kanda DIL adapter features: - Connector for Usbasp Programmer AVR Atmega8 Atmega128 Code B0051 Available Price €1.29
Bus Pirate - v3.6a This little board is great for any type of prototyping - enables troubleshooting and debugging of any board with voltage from 0 to 5.5V. The board interprets the commands and sends them further via a proper protocol (ranging from UART through I2C up to HDD44780 LCD). The Pirate lets analyze as well the data sent back from the device to the computer terminal effectively allowing to decipher potential errors. The bootloader installed on the board enables the quick and easy update of firmware and changing the functionality of the board. This board features PIC24FJ64 and FT232RL USB-to-serial chip enabling swift communication over the mini-B USB port. On the other end of the board 2x5 pin header is placed with detailed descriptions of each pin. Code SP037 Backorder Price €37.99
SparkFun FTDI Basic Breakout - 5V This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards. Code SP023 Last items in stock Price €18.99
CP2102 USB 2.0 to RS232 RS485 TTL 3.3V 5V converter CP2102 USB 2.0 to RS232 RS485 TTL 3.3V 5V converter features: - Ideal for connecting TTL RS232 RS485 devices to your PC through the USB port Code C0011 Available Price €7.95
Module MAX3232 Converter RS232 to TTL Port DB9 female This product is widely used in radio modifications, cell phone flash, xbox360 flash detection, GPS, car, Flash, HDD repair, top box upgrade.It can be used to download MCU types. Module MAX3232 Converter RS232 to TTL Port DB9 female features: - Input voltage: 3.3 - 5 VDC- Multi-channel RS232 controller / receiver MAX3232- Transmission / reception speed up to 250 kbit / s- DB9 serial port- Interface with four pins: - TX: transmission signal - RX: reception signal - VCC: Supply voltage - GND: connects the power cathode- Operating temperature: -65 ° C - + 150 ° C- UART communication- Includes a 4-wire female / female connector for easy connection with the arduino Code C0016 Available Price €2.90
TTL Converter Module 5V - 3.3V Bidirectional 2 Channel I2C Logic Level This bidirectional logic level converter can be used with normal series, I2C, SPI and other digital signals. It does not work with an analog signal.It is very easy to use. The card must be powered from the two voltages (high and low voltage) used by the system.A high voltage (5 V for example) to the pin "HV", low voltage (3.3 V for example) in "LV", and the system ground to pin "GND". TTL Converter Module 5V - 3.3V Bidirectional 2 Channel I2C Logic Level features: - 2 high voltage channels and low voltage logic logic for bidirectional translation- 2 low voltage channels High voltage high voltage logic in unidirectional conversion- The board module is compatible, it can be inserted directly in the use test panel- HV to 5 V power Code M0154 Available Price €6.79
CP2102 USB 2.0 A RS232 Converter UART TTL Serial Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features: - Controller CP2102- 5 pins: 3.3v, 5.0v, TxR, RxD, GND- Standard USB type to male and 5 pin TTL connector- 3 Status LEDs: Power, RX and TX- USB 2.0 specification with 12Mbps maximum speed Code C0001 Available Price €3.70
USB to RS485 USB to 485 Max485 Converter Ideal for connecting RS485 devices to your PC through the USB port. USB to RS485 USB to 485 Max485 Converter features: - CH340 controller- Supported OS: Win XP, Vista, Win 7.8, OS, Linux- Work with Modbus, Profibus- USB 2.0 specification with 6Mbps of maximum speed- Measures: 60x 18x 14 mm Code C0003 Available Price €2.69
FTDI FT232RL USB-UART Converter - Mini USB FTDI FT232RL USB-UART Converter - Mini USB features: - Serial Converter USB-TTL 3.3V - 5V - LED indicator of Tx, Rx, power. - Communication: TTL COM Virtual RS232 RX / TX Transceiver - Voltage: 3.3V or 5V - per bridge - Pins: DTR, RX, TX, VCC, CTS, GND - Protections: Electronic fuse up to 500mA. - Size: 46 x 19 mm. Step 2.54mm. - Connection: Mini USB - Driver: Windows 7 / 8/10 Linux / Mac / Android - USB TO UART solution with mini USB connector - FT232RL original on board - Compatible with Mac, Linux, Android, WinCE, Windows 7/8 / 8.1 / 10 ... - 3 power mode: 5V output, 3.3V output or powered by the destination board (3.3V-5V) - 3 LEDs: TXD LED, RXD LED, POWER LED - Functional pins Code C0014 Available Price €12.95
TTL Level Converter 5V - 3.3V IO LJ245A TTL level conversion module 5V 3.3V IO Single Interchange Compatible I2C SPI.Use of high-speed dual-level IT supply level translator chip design. TTL Level Converter 5V - 3.3V IO LJ245A features: - Main chip: Octal bus transceiver and change from 3.3-V to 5-V with outputs of 3 states LJ245A of Texas Instrument- VCCA power supply voltage: 4.5 - 5.5 VDC- VCCB power supply voltage: 2.7 - 3.6 VDC- Low level input voltage V (IL): 0.8 V- High-level input voltage V (IH): 2 V- Low level output current I (OL): 12 - 24 mA- High level output current I (OH): -24 - -12 mA- 8 channels allow the conversion of the IO communication level- Channel levels A and B are controlled by VCCA and VCCB Code C0017 Available Price €3.95
6-pin/10-pin Kanda DIL adapter 6-pin/10-pin Kanda DIL adapter features: - Connector for Usbasp Programmer AVR Atmega8 Atmega128 Code B0051 Available Price €1.29
Bus Pirate - v3.6a This little board is great for any type of prototyping - enables troubleshooting and debugging of any board with voltage from 0 to 5.5V. The board interprets the commands and sends them further via a proper protocol (ranging from UART through I2C up to HDD44780 LCD). The Pirate lets analyze as well the data sent back from the device to the computer terminal effectively allowing to decipher potential errors. The bootloader installed on the board enables the quick and easy update of firmware and changing the functionality of the board. This board features PIC24FJ64 and FT232RL USB-to-serial chip enabling swift communication over the mini-B USB port. On the other end of the board 2x5 pin header is placed with detailed descriptions of each pin. Code SP037 Backorder Price €37.99
SparkFun FTDI Basic Breakout - 5V This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards. Code SP023 Last items in stock Price €18.99
CP2102 USB 2.0 to RS232 RS485 TTL 3.3V 5V converter CP2102 USB 2.0 to RS232 RS485 TTL 3.3V 5V converter features: - Ideal for connecting TTL RS232 RS485 devices to your PC through the USB port Code C0011 Available Price €7.95
Module MAX3232 Converter RS232 to TTL Port DB9 female This product is widely used in radio modifications, cell phone flash, xbox360 flash detection, GPS, car, Flash, HDD repair, top box upgrade.It can be used to download MCU types. Module MAX3232 Converter RS232 to TTL Port DB9 female features: - Input voltage: 3.3 - 5 VDC- Multi-channel RS232 controller / receiver MAX3232- Transmission / reception speed up to 250 kbit / s- DB9 serial port- Interface with four pins: - TX: transmission signal - RX: reception signal - VCC: Supply voltage - GND: connects the power cathode- Operating temperature: -65 ° C - + 150 ° C- UART communication- Includes a 4-wire female / female connector for easy connection with the arduino Code C0016 Available Price €2.90
TTL Converter Module 5V - 3.3V Bidirectional 2 Channel I2C Logic Level This bidirectional logic level converter can be used with normal series, I2C, SPI and other digital signals. It does not work with an analog signal.It is very easy to use. The card must be powered from the two voltages (high and low voltage) used by the system.A high voltage (5 V for example) to the pin "HV", low voltage (3.3 V for example) in "LV", and the system ground to pin "GND". TTL Converter Module 5V - 3.3V Bidirectional 2 Channel I2C Logic Level features: - 2 high voltage channels and low voltage logic logic for bidirectional translation- 2 low voltage channels High voltage high voltage logic in unidirectional conversion- The board module is compatible, it can be inserted directly in the use test panel- HV to 5 V power Code M0154 Available Price €6.79
CP2102 USB 2.0 A RS232 Converter UART TTL Serial Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features: - Controller CP2102- 5 pins: 3.3v, 5.0v, TxR, RxD, GND- Standard USB type to male and 5 pin TTL connector- 3 Status LEDs: Power, RX and TX- USB 2.0 specification with 12Mbps maximum speed Code C0001 Available Price €3.70