Logic Level Converter 3.3 / 5V I2C IIC 3.3V/5V I2C logic level converter module with soldering pins.Ideal to connect a device that works at 3.3V to one that works with 5V.It works with digital signals (high and low levels).Logic Level Converter 3.3 / 5V I2C IIC features:- Voltage: 3.3V/5V- Measures: 1.5x 1 cm Code C0004 Available Price €1.69
10m Rigid cable, 22AWG black PVC wire, 0.35mm2 Characteristic: -Conductor: solid wire, tinned copper -Insulation: PVC -Low voltage electrical cables - Nominal voltage 300V / 80C -Standard: UL 1007 -Number of conductors: 22AWG, 1x0.35mm2 -Outer diameter: 1.6mm Code K0224 Backorder Price €3.89
Connector Jack 2.1x5.5mm Power Supply DC Male Jack connectors 2.1mm inside and 5.5mm outside to power devices such as LED strips, CCTV (Cameras), Arduino. Connector Jack 2.1x5.5mm Power Supply DC Male features: - Ideal for connecting without welding- It has two screws in the tip for positive and negative cable screwdriver Code K0023 Available Price €0.80
Breadboard Power Supply Protoboard 830/400 Points MB102 Ideal for your electronic projects, arduino, but can also be used with other microcontrollers. Breadboard Power Supply Protoboard 830/400 Points MB102 features:- Input voltage supports up to 12V- Selectable 3.3V or 5V- USB input or standard DC 2.1 x5.5mm connector- Maximum current 700mA- It fits perfectly on the MB-102 breadboard feeding the two lateral buses- Weight: 15 gr. (approx.) Compatible only with MB-102 type plates Code A0003 Available Price €1.95
Prototype Board MB102 Protoboard 830 points for Arduino Prototype Board MB-102 Protoboard 830 points Arduino features: - 830 Connections - Linkable with other boards - Base with adhesive to attach it to the work surface - Measures 165x 55x8mm Code PB004 Available Regular price €2.99 -€0.50 Price €2.49
Helping Magnifying Hand Tool It is a very ideal tool when the third hand is required.Helping Magnifying Hand Tool features:- Magnifying glass diameter 60mm- Weight: 0.5kg- Dimensions: approx. 15 (26) x 17 x 7cm Code H0011 Available Price €7.95
IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features: - Based on the PCF8574A chip - Power: 5V - Supports I2C Protocol - A potentiometer for regulate contrast - Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20 PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL - Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32 Code P0008 Available Price €1.39
MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG features: - Main chip: MQ-2 flammable gas and smoke sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Concentration detection: 200ppm - 5000ppm LPG, propane 300ppm - 5000ppm butane 5000ppm - 20000ppm methane 300ppm - 5000ppm H2 100ppm -2000ppm alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0027 Available Price €2.89
Wifi module adapter ESP12 ESP12E The adaptor for the well-known ESP-12 and ESP-12E module Code W0025 Available Price €0.90
Micro Usb to DIP Adapter Mini Arduino Module Electronic Converter PCB Micro Usb to DIP Adapter Mini Arduino Module Electronic Converter PCB features: - Compatible with male pin strip (pin spacing 2.54mm) - PCB dimensions: 15mm x 13mm Code M0044 Available Price €0.98
Qwiic cable 100mm It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 100mm long Code SP022 Available Price €1.99
Wireless Module Arduino compatible HC-06 HC06 The Bluetooth HC-06 module is one of the best options for projects where you need wireless communications. Arduino Wireless Module HC-06 HC06 features: - CSR BC417 Chipset - Power: 3.3V - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz band ISM - Modulation: GFSK - Range approx. 10m - Security: Authentication and encryption. - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port - Working temperature: -20 ºC to +75 ºC - Working current - pairing: 80 mA - Transmission: 8mA - Size: 28 x 12mm Code W0018 Available Price €9.50
Expansion Module I/O XBEE This XBEE module contains everything you need to create your projects, including socket to mount an XBee device, VDC power pins, GND, terminal block to power a servo motor, reset button and much more. The new expansion IO Shield V7.1 offers several advantages and these are its characteristics.Compatible with the new Arduino Due. Code M0150 Available Price €8.49
ENC28J60 Ethernet LAN Network Module for Arduino AVR LPC STM3 The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module for Arduino AVR LPC STM3 features: - Chip ENC28J60 Microchip- Module: 10Base-T- 3.3V power- SPI interface- 25Mhz speed- LED status LED- Hanrun network transformer- Network Interface board HR911105A- Operating temperature: -40ºC to + 85ºC- Dimensions: 55x 35x 16 mm Code W0002 Available Price €8.99
SSR-25 DD 25A DC-DC Solid State Relay 5V-60VDC output The DC-DC 25A solid state relay has a 3-32VDC input and a 6-60VDC output. It has a maximum load capacity of 25A. It has a long operating life and high reliability, a compact size. This relay switches very quickly. Fotek SSR-25 DD 25A DC-DC Solid State Relay 5V-60VDC output Code RL017 Available Price €7.99
LED matrix module 32x8 red MAX7219 SPI Voltage Sensor Module 0.02445V ~ 25V. When the module is powered by 5V the voltage detection does not exceed 25V, and when the module is powered with 3.3V the voltage detection does not exceed 16.5V. Arduino Compatible. Code M0192 Available Price €7.95
Transductor Conducción ósea 8Ohm Altavoz 1W + MAX98306 Amplificador Estéreo M115 Bone Conduction Transducer + MAX98306 Stereo Amplifier features:- Transducer Bone conduction 8Ohm Speaker 1W + MAX98306 Stereo Amplifier- Class D 3.7W stereo audio amplifier - MAX98306 Code M0115 ✗ Out-of-Stock Regular price €29.74 -3% Price €28.85
DC voltage sensor 0-25v for Arduino Voltage Sensor Module 0.02445V ~ 25V. When the module is powered by 5V voltage detection It does not exceed 25V, and when the module is powered with 3.3V the voltage detection does not exceed 16.5V. 100% Compatible with Arduino. DC voltage sensor 0-25v for Arduino features: - Input voltage: 0-25 VDC - Voltage detection range: 0.02445V-25 VDC - Analog voltage resolution: 0.00489 V - DC input connector: cathode terminal connected to VCC, GND negative pole - Output interface: "+" then 5 / 3.3V, "-" then GND, "s" then the Arduino AD pins Code M0191 Available Price €1.59
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 Available Price €4.49
DS3231 Precision RTC Real Time Clock Module AVR ARM DS3231 Precision RTC Real Time Clock Module AVR ARM features: - Can be used in projects of Arduino, Raspberry Pi, PIC, AVR- Function compatible with the DS 3231- Power supply voltage: +2.3 V to +5.5 V- Temperature range: -40 ° C to + 85 ° C- Low energy consumption- Full clock calendar functions that include seconds, minutes, hours, date, month and year and valid until leap year compensation- Two alarm calendar- Interface: I2C Code RA011 Available Price €2.95
Bus Pirate - v3.6a This little board is great for any type of prototyping - enables troubleshooting and debugging of any board with voltage from 0 to 5.5V. The board interprets the commands and sends them further via a proper protocol (ranging from UART through I2C up to HDD44780 LCD). The Pirate lets analyze as well the data sent back from the device to the computer terminal effectively allowing to decipher potential errors. The bootloader installed on the board enables the quick and easy update of firmware and changing the functionality of the board. This board features PIC24FJ64 and FT232RL USB-to-serial chip enabling swift communication over the mini-B USB port. On the other end of the board 2x5 pin header is placed with detailed descriptions of each pin. Code SP037 Last items in stock Price €39.99
Lilypad Slide Switch Board 2 Positions Interruptor This is a simple slide switch for LilyPad. Use it as a simple On / Off switch, or to control LEDs, buzzers, sensors, etc.The switches in each panel have a capacity of 4V to 300 mA, but will operate at 5V with a current reduction.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Slide Switch Board 2 Positions Interruptor features: - Switch two positions: On (ON) / Off (OFF)- Density of the PCB: 0.8 mm- Size: 7.75x18.1 mm Code M0141 Available Regular price €1.99 -€0.50 Price €1.49
Passive Buzzer 5V The piezoelectric buzzer has a simple structure in which a ceramic piezoelectric disk is affixed to a vibrating plate. An alternative voltage applied to this element will cause a contraction or diametrical expansion of the element. This feature is used to fold a vibrating plate, which generates sounds. 2x Passive Buzzer 5V features: - Input voltage: 3V to 12V - Diameter: 12mm - Height: 7.5mm - Pin spacing: 6.5mm - Impedance: 16 Ohm - Working frequency: 2 to 5 KHz - Quantity: 1 unit Code M0011 Available Price €0.39
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.95
Mini Submersible Water Pump DC 12V 200L/h 3W for ARDUINO Mini Submersible Water Pump DC 5.5-12V 200L / H 3W Mini Submersible Water Pump DC 12V 200L/h 3W ARDUINO features: * Operating voltage: 5.5-12V * Max flow: max. 200 l / h * Maximum pumping height: 40cm- max. 150cm * Cable length: 140cm * Jack DC 5.5x2.1mm connector (ext / int) * Outlet diameter: 8 mm * Dimensions: 36mm x 25mm Code M0111 Available Price €9.95
ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu Allows control: - Up to 2 bidirectional current motors- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A- Logic voltage: - 2.3V <= HIV <= VIN (high) - 0.3V <= VIL <= 1.5V (low)- Controller L293D- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA- D2, D4 - motorB Code W0015 Available Price €3.49
Full Color SMD LED Module RGB KY-009 This module specially designed for Arduino will allow you to generate a light of any color (RGB) quickly and accurately. The SMD LED Module RGB, consisting of an LED capable of creating any color using RGB, has a PWM voltage input with three pins. These are capable of shining in a wide range of colors thanks to the mixture of the three primary colors (red , green and blue). These types of diodes are called RGB and are made up of three red, green and blue diodes in the same package. Thanks to the variation of the intensity of these three diodes, we can create a composition of colors. With this led you can handle more than 16.5 million colors. Code M0080 Available Price €2.95
SONOFF DS18B20 - Temperature sensor with transmitter 1m This 1-meter probe uses the original DS18B20 temperature sensor chip. The DS18B20 is a waterproof temperature sensor/thermometer. It is waterproof, moisture proof and rustproof with the high quality stainless steel tube encapsulated. This is a spare part or accessory used in SONOFF TH10 / TH16. Code WS018 Available Regular price €9.90 -€3.00 Price €6.90