6-pin/10-pin Kanda DIL adapter

This module equipped with a PCF8591 converter has a low current power supply and includes 8 bit CMOS data acquisition devices.
Your converter has four analog inputs, one analog output and one I2C serial bus interface.
It is supplied in the voltage range 2.5V-6V, analog voltage between the negative potential VSS and positive VDD. The control and data signals are transmitted on the two-wire I2C bi-directional bus to the transformed series.
The intensity of the ambient light can be converted into a digital signal thanks to its integrated photoresistor.
It allows access to eight PCF8591 converters on the same I2C bus without additional equipment. Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V features:
- Supply voltage (between VSS and VDD): 2.5-6VDC

This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards.

An RS232 serial port to your PC through the USB port USB 2.0 A Serial Port Cable Adapter DB9 RS232 Series features:
- CH341 driver
- Supported OS: WinME, Win2003, Win XP, Vista, Win 7, Linux, MAC OS9.0/OSX
- High quality, shielded cable
- Power and data in the same cable, does not require more adapters
- Compatible USB interface 1.1 and 2.0
- Support up to 1 mega data transfer
- Length 73cm The adapter allows you to connect a computer with: - Electric meters
- Decoders, programmers
- Cash registers
- Satellite TV
- Control panels
- Mobile phones
- Diagnostic interfaces for cars
- The administration of Cisco routers

Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features:
- Controller CP2102
- 5 pins: 3.3v, 5.0v, TxR, RxD, GND
- Standard USB type to male and 5 pin TTL connector
- 3 Status LEDs: Power, RX and TX
- USB 2.0 specification with 12Mbps maximum speed

Ideal for connecting TTL RS232 devices to your PC through the USB port. USB to A RS232 UART TTL 5V Converter + Cables features:
- Compatible controller PL2303HX
- 5 pins: 3.3v, 5.0v, TXR, RDX, GND
- Heat shrinkable insulating cover
- LED indicators of data transmission
- 2.5A self-recovery protective fuse
- Supported OS: WinME, Win2003, Win XP, Vista, Win 7, Linux
- Weight: 40 gr. (approx.)

A multiplexer of this type actually only acts as a switch 16 to a 1.
The 4 digital pins are used to set high or low, (binary Y0-Y15) to determine which input pin is connected to pin "Z".
The control input S0-S3 is set to low "logic level 0", the signal C0 is connected to the output Z. Multiplexer 16 Channels CD74HC4067 MUX/DEMUX features:
- Based on chip CD74HC4067
- Analog signal input: Y0-Y15, 16 channels
- Analog signal output: Z pin
- Digital input, channel control: S0-S3
- Module size: approx. 4 x 1.8cm
- Package includes:
* 1 x CD74HC4067 MUX connection module
* 2 x row of soldering pins

Connecting a 3.3V device to a 5V system is a challenge.
The bidirectional logic level converter is a small device that safely drops the signals from 5V to 3.3V and increases 3.3V to 5V at the same time.
This level converter also works with 2.8V and 1.8V devices. What really separates this logic level converter from our previous versions is that it can successfully set its high and low voltages and go up and down between them safely on the same channel.
Each level converter has the ability to convert 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side. The level converter is very easy to use. The board needs to be powered from the two sources of voltage (high voltage and low voltage) that your system is using.

Characteristic: - AVR 5V / 3.3V microcontrollers - change the programming voltage through jumper JP1
- LED status indicators - Transmission speed: 5kB / s
- Fuse protector against possible damage to the USB port
- Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux
- Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦
- Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny15 € ¦
- CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦
- AT90S2313 series, AT90S2323, AT90S2343, AT90S4414, AT90S4433 € ¦

The PCF8591 is a low-power 8-bit single-chip, single-chip, 8-bit data acquisition device with four analog inputs, an analog output, and an I2C serial bus interface.
Three address legs A0, A1 and A2 are used to program the hardware address, allowing the use of up to eight devices connected to the I2C bus without additional hardware.
Address, control and data to and from the device are transferred in series through the two-way bidirectional I2C bus. Analogue to Digital Converter PCF8591T features:
- Main chip: PCF85911
- Operating voltage supply: 2.5 - 6 V
- Low standby current
- Serial input / output through the I2C bus
- 3 hardware address pins A0, A1, A2
- Sampling speed given by the I2C bus speed

Ideal for connecting RS485 devices to your PC through the USB port. USB to RS485 USB to 485 Max485 Converter features:
- CH340 controller
- Supported OS: Win XP, Vista, Win 7.8, OS, Linux
- Work with Modbus, Profibus
- USB 2.0 specification with 6Mbps of maximum speed
- Measures: 60x 18x 14 mm