Screw Shield V1 for Arduino UNO y MEGA Screw Shield V1- Arduino ScrewShield UNO y MEGA features: Screw Shield V1 allows: - Being punctured directly to an Arduino Uno, Mega, Leonardo plate- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more. Code M0173 Available Price €3.95
ATmega2560 R3 REV3 16U2 Mega2560 module with USB cable It has an Atmega2560 chip running at 16Mhz with a factory loaded bootloader with 54 digital input / output pins (from which 14 can be used as PWM outputs) and 16 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, an ICSP port, a reset button and some status LEDs. Atmega16U2 programmed as a USB-to-serial converter. Simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Code B0003 Available Price €24.90
PAM8403 2x3W Digital Amplifier Channel Stereo PAM8403 2x3W Digital Amplifier Channel Stereo features: - Up to 3W in each channel- Chip: PAM8403- Power supply: 5V- Power: 2 outputs of 3 watts each- Measures: 21x18 mm- Suitable impedance speakers: 4 Ohm Code M0027 Available Price €1.89
Vertical Liquid Level Sensor Switch Level sensor for liquids with float. The liquid level sensor acts as a switch. The state is changed by means of a magnet located on the float. It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where it is necessary to control the level of non-corrosive liquids such as water tanks, aquariums. Characteristic: - Maximum Load: 50W - Maximum Switching Voltage: 250V - Maximum Switching Current: 0.5A - Maximum charging current: 1A - Operating temperature: -10ºC to + 60ºC - Size: 58mm x 18mm Code S0043 Available Price €2.95
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.99
Current Sensor ACS712 AC/DC 20A Hall Current Ammeter Sensor used to measure the current in the circuit to which it is connected. It is based on the ACS712 chip, capable of measuring intensity in both DC and AC. Current Sensor ACS712 AC/DC 20A Hall Current Ammeter features: - Output: Analog - Power: 5V - Accuracy: 1.5% - Measuring capacity: +/- 20A - Dimensions: 31 x 13 mm Code M0105 Available Price €2.99
Rotary Encoder EC11 with Push Button Switch It can be used to control the microprocessor of the Arduino AVR PIC system and others, or as a digital potentiometer rotating the rotary encoder can be counted in positive and negative, depending on the direction of rotation; with the button of the rotary encoder can be reset to its initial state, which starts counting from 0. Code M0213 ✗ Out-of-Stock Price €1.39
Bluetooth Transceiver Module HC-05 Wireless - HC-05 Bluetooth transceiver module with base- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.Bluetooth Transceiver Module HC-05 Wireless features:- Chipset CSR BC417- 3.6 to 6 Vdc power supply- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps Code W0004 Available Price €5.39
Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna A Mini WIFI board ESP8266 contains 16MB flash, external antenna connector and built-in ceramic antenna based on ESP-8266EX. Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features: - Compatible with Arduino, programming with the Arduino IDE, MicroPython, NodeMCU - Supply voltage: 5V - Logical levels: 3.3V - 16MB (128Mbit) flash - 11 pins of input / output - I2C / one-wire interface, LOLIN I2C port - 1 ADC (input: 0-3.2V) - built-in ceramic antenna - external antenna connector - Power switch - Includes external WIFI antenna with IPEX SMA adapter Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features: of esp8266: - Supported protocols: 802.11 b / g / n - Network support: 2 , 4 GHz Code W0098 Available Price €10.90
W5500 Ethernet Arduino Shield UNO Web Server Expansion Module The Ethernet module for Arduino and compatible boards based on the Wiznet W5500 chip, faster than the previous W5100. It provides an easy way to connect your module to the local network and internet based WIZNET with a TCP/IP interface. Compatible with libraries with the same Ethernet API. A web server can be built with this UNO board shield. It can be used as a server or as a client. Code W0106 Available Price €19.50
Shield Li-Po Battery for WeMos D1 Mini ESP826 Shield Li-Po Battery for WeMos D1 Mini ESP826 features: Connect the lithium battery to this shield to supply power for the entire D1 mini system. When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V - Charging current: max: 1A - Voltage lithium battery: 3.3-4.2V - Boost power supply: 5V (max: 1 A) - LED color: red for charging, green for fully charged - Ports: * Micro USB - Charging port (normal 5V) * Connect to the lithium battery (normal 3.3-4.2V) * J1 - setting the maximum charging current, 0.5 A or 1A Code W0076 ✗ Out-of-Stock Price €4.76
DC voltage sensor 0-25v for Arduino Voltage Sensor Module 0.02445V ~ 25V. When the module is powered by 5V voltage detection It does not exceed 25V, and when the module is powered with 3.3V the voltage detection does not exceed 16.5V. 100% Compatible with Arduino. DC voltage sensor 0-25v for Arduino features: - Input voltage: 0-25 VDC - Voltage detection range: 0.02445V-25 VDC - Analog voltage resolution: 0.00489 V - DC input connector: cathode terminal connected to VCC, GND negative pole - Output interface: "+" then 5 / 3.3V, "-" then GND, "s" then the Arduino AD pins Code M0191 Available Price €1.59
M12 High Resolution Lens, 5MP, 20.2° FOV, 25mm Focal length, Compatible with Raspberry Pi High Quality Camera M12 M12 Long Focal Length Lens, 5MP, Long Focal Length 25mm, F1.7 Large Aperture, Compatible with Raspberry Pi High Quality Camera M12 Code WV014 Available Price €22.95
Bluetooth Transceiver Module HC-06 Wireless HC-06 Bluetooth transceiver module with base.The bluetooth module HC-06 is one of the best options for projects, in which you need wireless communications.The transceiver module allows bluetooth wireless connections as a slave, ready to listen for connection requests. Bluetooth Transceiver Module HC-06 Wireless features: - Chipset CSR BC417- 3.5V - 5V power- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps- Supports AT commands for configuration through a serial port- Working temperature: -20ºC to + 75ºC- Working current - pairing: 80 mA Code W0009 ✗ Out-of-Stock Price €5.39
Mini Submersible Water Pump DC 12V 200L/h 3W for ARDUINO Mini Submersible Water Pump DC 5.5-12V 200L / H 3W Mini Submersible Water Pump DC 12V 200L/h 3W ARDUINO features: * Operating voltage: 5.5-12V * Max flow: max. 200 l / h * Maximum pumping height: 40cm- max. 150cm * Cable length: 140cm * Jack DC 5.5x2.1mm connector (ext / int) * Outlet diameter: 8 mm * Dimensions: 36mm x 25mm Code M0111 Available Price €9.95
8 Channel High Trip 5V 10A Relay Module This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, from the TTL 8 Channel High Trip 5V 10A Relay Module features: - Channels: 8 (independent protected with Optocouplers) - Supply Voltage Vcc: 5Vdc - Output Current: 10A - High trip min 3.3V input IN1. ..IN8 - Relay activation current: 5 ~ 10mA - Isolation: Yes - Indicator LED: For each channel - Dimensions: 55x 139mm - Weight: 120g COM GND jumper input: connects GND optocouplers and GND of the circuit Code RL015 Available Price €9.95
NRF24L01 + Wireless Transceiver Module 2.4GHz It is ultra compact and very low consumption. It works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripheral control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Transceiver Module 2.4GHz features: - Based on chip NRF24L01 + Ultra Low Power- Free band: 2.4GHz ISM- Speed: 250kbps, 1Mbps, 2Mbps- Working current - reception: 13 mA- Transmission: 11 mA (900nA -deep sleep mode)- Receiving sensitivity: -94dB 250kbps- Coverage in closed spaces: 15m / 30m- SPI interface- Input voltage: 1.9V- 3.6V- Input / output port voltage: 0V-3.3V / 5V- Coverage in open areas: 100m approx.- Clock frequency: 16MHz Code W0005 Available Price €1.59
SIM900 Four Band GSM GPRS Module with Antenna shield for Arduino SIM900 Four Band GSM GPRS Module with Antenna shield for Arduino features: - GSM / GPRS SIM900 module-based development card / shield from Simcom - The shield allows you to get SMS, MMS, GPRS and audio via UART by sending AT commands (GSM 07.07, 07.05 and SIMCOM Enhanced COM Commands). - The shield also has 12 GPIOs, 2 PWMs and a ADC of the SIM900 module (All of them are 2V8 logic) present on board. - Quad-Band 850/900/1800/1900 MHz: it would work on GSM networks in all countries of the world. - GPRS multi-slot class 10/8 - GPRS mobile station class B - Complies with GSM phase 2/2 + - Class 4 (2 W @> Code W0090 Available Regular price €25.99 -€3.50 Price €22.49
M12 High Resolution Lens, 5MP, 20.2° FOV, 25mm Focal length, Compatible with Raspberry Pi High Quality Camera M12 M12 Long Focal Length Lens, 5MP, Long Focal Length 25mm, F1.7 Large Aperture, Compatible with Raspberry Pi High Quality Camera M12 Code WV014 Available Price €22.95
8x8 LED Matrix Kit MAX7219 Arduino compatible PIC Dot Matrix Display Cascade DIY 8x8 LED Matrix Kit MAX7219 Arduino PIC Dot Matrix Display Cascade DIY features: - 8X8 LED matrix controlled by MAX7219 chip - 3mm red LED - SPI communication - Voltage: 4.7 - 5.3V DC - Interfaces to manage multiple modules in cascade - Matrix dimensions: 32mm x 32mm x 8mm - PCB dimensions: 32mm x 50mm Code M0062 Available Price €2.95
Wireless Transceiver Module with Antenna CC1101 This external wireless antenna module CC1101 is suitable for Funduino and Arduino projects.The CC1101 module of 1.2K baud consists of a domestic R & Lotes unit to improve the effective communication distance.This is a significant improvement over the CC1100 module.It allows to adjust the speed of the bits for different uses, thus allowing a higher transmission speed.Supports 2-FSK, GFSK and msk modulations. It also has a high sensitivity (1.2kbps @> Code W0083 Available Price €8.49
Timer Relay Module FRM01 The multifunctional relay control module, FRM01, is designed for customers with different synchronization and control needs.The FRM01 is controlled by the STM8S003F3P6 microcontroller and has 18 different functions.Each function can be customized to meet customer needs in a variety of time and power control applications.The FRM01 is equipped with a high-quality power relay, a high-power voltage transistor, red and blue LED indicators, an LED display on a double-sided PCB board.The output of the board is driven by a high quality power relay capable of controlling the AC and DC loads. Timer Relay Module FRM01 features: - Operating voltage: 12 VDC- 4 buttons: SET, SWI, NUM +, NUM-- Operating temperature: -20 °C - + 60 °C Code M0159 Available Regular price €9.95 -€2.00 Price €7.95
SONOFF L1 - Intelligent LED strip light WiFi IP65 5M Intelligent 5 metre LED strip by WiFi and RF, great for creating any atmosphere in any room. Change its colour and rhythm from your mobile phone or its remote control. Dance to the rhythm of the lights, copy the colour from your mobile or control the lighting with your voice assistant like Alexa or Google Home. Decorate your home with an infinite number of possible scenes. Code WS016 ✗ Out-of-Stock Price €36.99
NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino compatible NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0065 ✗ Out-of-Stock Price €1.49
MAX98306 3.7W Stereo Amplifier MAX98306 3.7W Stereo Amplifier - Class D Stereo Audio Amplifier 8 Ohm. Code M0117 ✗ Out-of-Stock Price €14.79
ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0014 Available Price €4.95
TUYA IoT Interface for controlling Arduino over WiFi TUYA IoT interface module - you will be able to control your projects IoT Internet of Things interface of your Arduino. Tuya interface that allows you to control outputs of the Arduino module via WiFi network using apps for Android and iOS mobile devices. The device communicates with Arduino via UART interface, powered by 5V. Code WT017 Last items in stock Price €18.90
16-bit I2C ADS1115 module, 4-channel ADC with professional gain amplifier PGA The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden. Code M0226 Available Price €5.95