Cable 1x0.35 Flexible single-pole 0.35mm black 1m Cable 1x0.35 Flexible single-pole 0.35mm² black features: -Conductor: Flexible Copper -Insulation: PVC -Low voltage electrical cables -Standard: EN 50525-2-31 -Number of conductors: 1x0.35mm² -Service voltage: 300 / 500V -Service temperature: at 70ºC -Resistance at 20ºC: 55.0 Ohm / Km -Weight (Kg / Km): 7 -Outer Diameter: 2.4mm Code K0031 Backorder Price €0.37
Micro Motor 3V 5V 6V DC DIY for Arduino UNO Mega Robotics For Arduino, Smart Car, Robotics.Small electric motor magnet for direct current (DC). Micro Motor 3V 5V 6V DC DIY Arduino UNO Mega Robotics features: - Operating voltage: 1.5V to 6V- DC current: 350mA- Torque max.: 15g / cm- Max speed: 12000rpm- Weight: 16.5 g Code R0037 Available Price €0.81
Large Red Crocodile Connector It is used to pass the current, power electrical and electronic circuits, fans, motors, among others. Large Red Crocodile Connector features: - Total length: 51 mm- Red color- Isolated terminals: no- Maximum opening: around 10 mm- Conductive material: nickel-plated steel- Includes 1 unit Code K0128 Available Price €0.32
Rain Sensor Module Water Droplet Detector The module has two outputs: analog A0 and digital D0. digital output D0 - signal 0 or 1 appears depending on the configuration of threshold. The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - digital switching output indicator - Measurements PCB: 3 x 1.5 cm - Sensor measurements: 5.4 x 3.9 cm Code S0022 Available Price €1.40
VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features: > - Input voltage 2.5V-3V - Operating power 60mW / 15fps VGA YUV - Resolution VGA 640x480 pixels (30fps) - Maximum frame rate 30fps VGA - Flicker 50Hz / 60Hz automatic detection - Lens size 1/6 " - Angle of view 25 ° - Sensitivity 1.3V / (lux- seg) - SCCB (Serial Camera Control Bus) interface - Output format · 8 Bits - YUV / YCbCr 4: 2: 2 - RGB 565/555/444 - GRB 4: 2: 2 - RAW RGB data - High sensitivity Light operation - Automatic adjustment - Color level saturation - Edge enhancement - Noise level Code M0103 Available Regular price €4.79 -€1.00 Price €3.79
Desoldering Wire 1mm 1.0 High grade in the absorption of tin for professionals.Copper mesh roll for desoldering electronic components.Desoldering Wire 1mm 1.0 features:- Material: Copper- Length: 1.5m- Width: 1.0mm- Desoldering Braid Solder Remover Wick 1mm / 1.5m- Pure copper braid construction- Quick removal welding- Excellent thermal for a faster and safer desoldering Code H0003 Available Price €1.48
T-Cobbler GPIO KIT + 40-pin Grey Flat Cable Pi B+ RPI 2 RPI 3 RPI Zero T-Cobbler GPIO KIT + 40-pin Grey Flat Cable Pi B+ RPI 2 RPI 3 RPI Zero features: - Shield to connect with breadboard - Dimension: 6 x 7.3x 1.9mm - Flat cable female / female 40 pins - Total length: 25cm - Quantity: 1x shield 1x flat cable Code RA010 Available Price €4.91
4x4 High Quality Keyboard Matrix Push Buttons 16 Touch Keys High quality keyboard, with 16-key matrix.Ideal for your arduino projects, but can also be used with other microcontrollers. 4x4 High Quality Keyboard Matrix Push Buttons 16 Touch Keys features: - Momentary contact- Number of push buttons: 16- Dimensions: 39mm x 43mm Code M0009 Available Price €1.23
M12 Inductive Proximity Sensor NPN DC 6-36V LJ12A3-4-Z/BX 3D Printer M12 Inductive Proximity Sensor NPN DC 6-36V LJ12A3-4-Z/BX 3D Printer features: - This sensor can be configured as Z axis auto level - Inductive proximity sensor detection switch LJ12A3-4-Z / BX - NPN DC6-36V - Often used for 3D printer bed leveling - Typical application: 3D printer bed level sensor - Type of Cylindrical DC cable 3 type of cable (black, brown, blue) - Inductive sensor type - NPN NO (Normal Open) - Detecting Distance 4mm - DC supply voltage 6-36V - 300mA current output - 0.5KHz response frequency - Detects iron / aluminum - Operating temperature -25 ° C to + 55 ° C (Condition non-freezing) - Head diameter 12 mm - Size 6.2 x 2cm - Cable length 100cm Code S0125 Available Price €2.88
M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer features: - This sensor can be configured as auto Z axis level - Sensor detection switch inductive proximity LJ12A3-4-Z / BY - PNP DC6-36V - Often used for 3D printer bed leveling - Typical application: printer bed level sensor 3D - Cylindrical cable type DC 3 cable type (black, brown, blue) - Inductive sensor type - PNP NO (Normal Open) - Detecting Distance 4mm - DC supply voltage 6-36V - Current output 300mA - Response frequency 0.5KHz - Detects iron / aluminum - Operating temperature -25 ° C at + 55 ° C (Non-freezing condition) - Head diameter 12 mm - Size 6.2 x 2cm - Cable length 100cm Code S0036 Available Regular price €3.30 -€0.50 Price €2.80
Inductive proximity sensor PL-05N 5mm with NPN output Inductive Proximity Sensor PL-05N NPN Limit Switch is used for controlling machinery as part of a control system, as a safety interlock, or to count objects passing a point. Inductive proximity sensor PL-05N 5mm with NPN output features: - Manufacturer: Fotek,- Square Type,- Sensing distance: 5mm,- Operating voltage: 10 - 30 VDC,- Response frequency: 800Hz,- Output method: NPN, 150mA load,- Hysteresis: <10% of sensing distance,- Protection degree: IP67,- Working temperature/Hum: -20ºC - +80ºC, 35% - 90% RH,- Body dimension: 30.5x17.9x10.2mm (LxWxH),- Mounting Method: Flush,- Sensing Direction: Horizontal,- Materia Housing: High-impact plastic,- Screw hole: 3.2mm, Pitch: 10.5mm, Code S0130 Available Price €9.83
Inductive proximity sensor PL-05P 5mm with PNP output Inductive Proximity Sensor PL-05P PNP Limit Switch is used for controlling machinery as part of a control system, as a safety interlock, or to count objects passing a point. Inductive proximity sensor PL-05P 5mm with PNP output features: - Manufacturer: Fotek,- Square Type,- Sensing distance: 5mm,- Operating voltage: 10 - 30 VDC,- Response frequency: 800Hz,- Output method: PNP, 150mA load,- Hysteresis: <10% of sensing distance,- Protection degree: IP67,- Working temperature/Hum: -20ºC - +80ºC, 35% - 90% RH,- Body dimension: 30.5x17.9x10.2mm (LxWxH),- Mounting Method: Flush,- Sensing Direction: Horizontal,- Materia Housing: High-impact plastic,- Screw hole: 3.2mm, Pitch: 10.5mm, Code S0131 Available Price €9.05
M12 Inductive Proximity Sensor NPN DC 6-36V LJ12A3-4-Z/BX 3D Printer M12 Inductive Proximity Sensor NPN DC 6-36V LJ12A3-4-Z/BX 3D Printer features: - This sensor can be configured as Z axis auto level - Inductive proximity sensor detection switch LJ12A3-4-Z / BX - NPN DC6-36V - Often used for 3D printer bed leveling - Typical application: 3D printer bed level sensor - Type of Cylindrical DC cable 3 type of cable (black, brown, blue) - Inductive sensor type - NPN NO (Normal Open) - Detecting Distance 4mm - DC supply voltage 6-36V - 300mA current output - 0.5KHz response frequency - Detects iron / aluminum - Operating temperature -25 ° C to + 55 ° C (Condition non-freezing) - Head diameter 12 mm - Size 6.2 x 2cm - Cable length 100cm Code S0125 Available Price €2.88
M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer features: - This sensor can be configured as auto Z axis level - Sensor detection switch inductive proximity LJ12A3-4-Z / BY - PNP DC6-36V - Often used for 3D printer bed leveling - Typical application: printer bed level sensor 3D - Cylindrical cable type DC 3 cable type (black, brown, blue) - Inductive sensor type - PNP NO (Normal Open) - Detecting Distance 4mm - DC supply voltage 6-36V - Current output 300mA - Response frequency 0.5KHz - Detects iron / aluminum - Operating temperature -25 ° C at + 55 ° C (Non-freezing condition) - Head diameter 12 mm - Size 6.2 x 2cm - Cable length 100cm Code S0036 Available Regular price €3.30 -€0.50 Price €2.80
Inductive proximity sensor PL-05N 5mm with NPN output Inductive Proximity Sensor PL-05N NPN Limit Switch is used for controlling machinery as part of a control system, as a safety interlock, or to count objects passing a point. Inductive proximity sensor PL-05N 5mm with NPN output features: - Manufacturer: Fotek,- Square Type,- Sensing distance: 5mm,- Operating voltage: 10 - 30 VDC,- Response frequency: 800Hz,- Output method: NPN, 150mA load,- Hysteresis: <10% of sensing distance,- Protection degree: IP67,- Working temperature/Hum: -20ºC - +80ºC, 35% - 90% RH,- Body dimension: 30.5x17.9x10.2mm (LxWxH),- Mounting Method: Flush,- Sensing Direction: Horizontal,- Materia Housing: High-impact plastic,- Screw hole: 3.2mm, Pitch: 10.5mm, Code S0130 Available Price €9.83
Inductive proximity sensor PL-05P 5mm with PNP output Inductive Proximity Sensor PL-05P PNP Limit Switch is used for controlling machinery as part of a control system, as a safety interlock, or to count objects passing a point. Inductive proximity sensor PL-05P 5mm with PNP output features: - Manufacturer: Fotek,- Square Type,- Sensing distance: 5mm,- Operating voltage: 10 - 30 VDC,- Response frequency: 800Hz,- Output method: PNP, 150mA load,- Hysteresis: <10% of sensing distance,- Protection degree: IP67,- Working temperature/Hum: -20ºC - +80ºC, 35% - 90% RH,- Body dimension: 30.5x17.9x10.2mm (LxWxH),- Mounting Method: Flush,- Sensing Direction: Horizontal,- Materia Housing: High-impact plastic,- Screw hole: 3.2mm, Pitch: 10.5mm, Code S0131 Available Price €9.05