M12 Inductive Proximity Sensor NPN DC 6-36V LJ12A3-4-Z/BX 3D Printer

The 28BYJ-48 has everything you need to start using stepper motors in your project
A stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller card
Can control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mA
Equipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features:
- Engine model: 28BYJ-48
- Phases engine: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per round: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm

5 meter LED strip easily installed for use with Sonoff controllers via WiFi and RF. Great lights to create any ambience in any room. Change their colour and rhythm from your mobile or controller. Dance to the rhythm of the lights, copy the colour from your mobile or control the lighting with your voice assistant like Alexa or Google Home. Decorate your home with an infinite number of possible scenes. (Controller and adapter not included)

Liquid Flux 50ml Solder Colophony Alcohol Base features:
- Liquid Flux alcohol-based for electronic welding
- Type of flux: Colophony
- No Clean, Lead Free, Non-conductive
- Form: liquid
- Type of packaging: bottle
- Use of welding equipment to tin elements coated with polyurethane varnishes
- Properties of welding equipment can be washed with alcohol-based agents
- Content of solid bodies: 24%
- Density (at a temperature of 20 ° C): 0.86g / cm3 The flux cleans and prepares the surfaces and components to be welded, it facilitates the adherence and fluidity of the tin thanks to the rest of the components.
It cleans easily with alcohol.

Resistor 150R Ohm 5% 0,25W 1/4W features:
-150R Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

A3967 controller, double H-bridge controller driver.
Allows to control up to 2 DC motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. A3967 DC Motor PAP Driver Stepper - Easy driver features:

- Minimum operating voltage: 7.00 V
- Voltage maximum operating: 30 V

It has an Atmega2560 chip running at 16Mhz with a factory loaded bootloader with 54 digital input / output pins (from which 14 can be used as PWM outputs) and 16 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, an ICSP port, a reset button and some status LEDs. Atmega16U2 programmed as a USB-to-serial converter. Simply connect it to a computer with a USB cable or power with a power adapter and DC connector.

Module for Arduino, Raspberry Pi 2 and Pi 3, B and B +.
The display module 4-digit LED with TM1637.
The unit can be controlled with just two DIO and CLK control lines.
TM1637 4-Digit Digital Display Module features:

- 3V-5V supply voltage
- Current consumption 250 mA
- 7-segment display 4 digits common anode
- Digit size: 0.36 inches
- Dimensions: 42x24x11mm

Speed sensor module for Arduino motors features:
- Slot-type optocoupler sensor, slot width: 10 mm.
- The encoder module is a device that can help you in the creation of your robotics and automation project, whether you want to know the speed of a motor or the exact position of it.
- Output Out - Emits a low level when there is no block in the slot, otherwise it produces a high level. The operating mode: - When the sensor is blocked the OUT output is high
- Power supply: 3.3-5V - Current consumption 15 mA max.
- PCB dimensions: 25 x 20 mm