Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM
  • Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM
  • Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM
  • Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM
  • Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM

Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM

M0136

This module, which uses the exclusive L298P chip for driving high-power motors, can directly control two DC motors, with a drive current up to 2A. The motor output uses eight-speed Schottky diodes as protection.
The design of the letter allows you to connect directly to the Arduino UNO R3 for easier use. Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM features:
- 1 logical step of the input voltage VD: 5 VDC
- Control of the input voltage VS and control by pulse width modulation:
      - VIN input: 6 - 12 VDC
      - PWRIN input: 4.8 - 35 VDC
- Logic current flow: Iss <36m A
- Operation current management: Io <2 A
- Maximum power dissipation 25W (T = 75 ° C)
- Input of the control signal:

OEM
5905323237469
Add to wish list

Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM description


This module, which uses the exclusive L298P chip for driving high-power motors, can directly control two DC motors, with a drive current up to 2A. The motor output uses eight-speed Schottky diodes as protection.
The design of the letter allows you to connect directly to the Arduino UNO R3 for easier use.

Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM features:


- 1 logical step of the input voltage VD: 5 VDC
- Control of the input voltage VS and control by pulse width modulation:
      - VIN input: 6 - 12 VDC
      - PWRIN input: 4.8 - 35 VDC
- Logic current flow: Iss <36m A
- Operation current management: Io <2 A
- Maximum power dissipation 25W (T = 75 ° C)
- Input of the control signal:
      - High voltage level: 2.3V
      - Low voltage level: -0.3V
- Material interface (Hardware): pin terminal 5.00 mm
- Belt clip and can be controlled through the access signal of the front row
- Driver type: L298 dual-power H bridge controller
- Pins D1-D7: direct drive motor
- Compatible with engine speed control in PWM / PLL mode
- Arduino UNO R3 compatible
- Operating temperature: -25 - 130 ° C
- Size: 68x58 mm

Customers who bought this product also bought

W1209 12V DC Thermostat Digital Temperature Controller Switch

W1209 12V DC Thermostat Digital Temperature Controller Switch features:
- Model: W1209
- Supply voltage: DC 12V
- Temperature control mode: ON / OFF
- Temperature range: -50 -110 ° C
- Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C
- Measurement accuracy: 0.1 ° C
- Refresh rate: 0.5 s
- Temperature protection 0-110 ° C
- Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA
- Power of output: 10A relay
- Sensor probe: NTC waterproof sensor (10K 0.5%)
- Environmental requirements: -10 ~ 60 ° C Humidity 20% -85%
- Dimensions: 48 x 40 mm

M0102

Price €3.13

ESP8266 5V WiFi Relay Module AP Remote Control + STA

You can easily control any device over the Internet through your phone, computer, etc.
The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point).
In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters).
In STA mode, the relay module is connected to the access point (router) that supplies the network.
Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers).
You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off.

W0067

Price €7.84

Cable 1x0.35 Flexible single-pole 0.35mm red 3m

Characteristic:
-Low-voltage electric cables
-Standard: EN 50525-2-31
-Number of conductors: 1x0.35mm2
-Service voltage: 300 / 500V
-Service temperature: at 70ºC
-Resistance at 20ºC: 55.0 Ohm / Km
-Weight (Kg / Km): 7
-Outer diameter: 2.4mm

K0033

Price €0.37

LDR Module Motor Resistance KY-018

This module adapted for the arduino is a light sensor. The resistance of the LDR cell decreases as the light intensity increases.
On the contrary in a dark environment, the resistance of the LDR cell increases accordingly. Characteristic: - 3-pin connector: 1- GND
2- VCC
3- analog output - the voltage depending on the light
- Supply voltage: 3.3 V-5VDC
- PCB size: 19x15x8 mm

S0122

Price €1.15
€9.50
Save €1.51 €7.99

7,99 tax excl.

1
13 items
Regular price €9.50 Price €7.99

Order until 4pm we will send today
30 days return