Mini precision polishing drill 12V with accessories + Power supply unit 12V electric drill, with ON/OFF switch with 2 grinding tips, 2 burrs, 4 nozzles Code H0244 Last items in stock Regular price €17.95 -€2.50 Price €15.45
10x Electrolytic Capacitor 470uF 16V 105ºC 10x Electrolytic Capacitor 470uF 16V 105ºC PIC Arduino features:-Type: Electrolytic Capacitor-Assembly: intern-Value: 470uF-Maximum tension: 16V-Maximum temperature 105º C-Dimensions: 8x12mm-Quantity: 10 units Code D0047 Available Price €0.13
Laminated Copper Clad Prototype PCB Circuit Board 30x19cm Laminated Copper Clad Prototype PCB Circuit Board 30x19cm. Code PB033 Backorder Price €5.69
Momentary Switch Push Button Red N/O 7mm Momentary Switch Push Button Red N/O 7mm features: - Momentary pushbutton N/O (normally open)- Red button- Dimensions approx. 7 mm x 27 mm- Recessed with nut and washer- Load current (supported): 1A to 230V / 2A to 125V- Drill to embed: 7 mm +/- 0.2- Operating temperature: -55º to +85ºC Code K0156 Available Price €0.45
Plate UNO CH340 + Arduino compatible switches It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader. The Uno R3 module has all connectors than the Arduino Uno R3 and is compatible with all Arduino shields. Plate UNO R3 CH340 + Arduino compatible switches features: - ATmega328P chip at 16MHz with crystal external quartz - ATmega328P microprocessor with socket - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6- 20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader -Atmega328 - SRAM 2 KB - Atmega328 Code B0023 ✗ Out-of-Stock Price €10.99
5S BMS 25A 21V 18650 PCM PCB Circuit Charging Module In the case of a battery pack, the BMS (Battery Management System) balancing protection circuit allows charging and discharging to be individually controlled. That is, the circuit controls that all cells are charged and discharged at approximately the same voltage. The current during charging should be limited, because the cell will "absorb" the current given to it, but a higher current than the one established by the manufacturer (generally a safe current is 1C ) can cause the cell to overheat and, in extreme cases, explode. The same relationship also applies to discharge. Code A0108 Available Price €4.69
Resistor 1K Ohm 5% 0,25W 1/4W Resistor 1K Ohm 5% 0,25W 1/4W features:-1 unit - 1K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0076 Available Price €0.09
Microcontroller ATMEGA8A-PU ATMEGA8 DIP-28 Atmel Microcontroller ATMEGA8A-PU ATMEGA8 DIP-28 Atmel features: - Series: AVR® ATmega- Core processor: AVR- Package / box: 28-DIP (0.300 ", 7.62 mm)- Core size: 8 bits- Speed: 16MHz- Connectivity: I²C, SPI, UART / USART- I / O Number: 23- Type of memory of the program: FLASH 8kB- EEPROM size: 512B- RAM size: 1kB- Voltage - Supply (Vcc / Vdd): 2.7 V ~ 5.5 V- Data converters: 10bit A / D- Type of oscillator: internal- Operating temperature: -40 ° C ~ 85 ° C- RoHS: Yes- Quantity: 1 unit Code T0007 Available Price €4.99
Battery holder 2x CR2032 Switch Characteristic: - Button cell battery - For 20mm diameter battery type CR2032 - ON / OFF switch - Dimension: 50mm (L) x 23mm (W) x 6mm (D) Code PP23 Backorder Price €1.19
Battery holder 2x 18650 PCB mount Base of two 18650 batteries to solder on PCB. Characteristic: - Measurements 78x 40x 21mm - Weight: 10 gr . (approx.) - Stack length max 67mm Code PP052 Available Regular price €2.49 -€0.40 Price €2.09
Adapter Battery 9V 6F22 Jack Connector DC Ideal to power your Arduino board through the power input.Adapter Battery 9V 6F22 Jack Connector DC features:- Cable 7cm long- Battery connector 9V, 6F22- Male connector DC 5.5 / 2.5 Code PP011 Available Price €0.75
Battery holder 2x AA Battery holder with switch Includes a switch to output the voltage built into the case itself. It has a cover to protect the batteries. The cover has perforation in case you want to secure it with a screw (not included). Battery holder 2x AA Battery holder with switch features: - Cable 15cm long - Measurements 68x 32x 18mm - Battery length max 50mm - Compatible batteries (LR06, R06, MN1500, AM3, UM3 , HP7) Code PP005 Available Price €1.39
Battery holder 2x 18650 3,7V Serial Battery holder for 18650 batteries connected in series. Code PP057 Available Regular price €2.09 -€0.30 Price €1.79
5x 9v Battery Adapter Connector 6F22 with Cable Ideal to power your Arduino board through the power input. 5x 9v Battery Adapter Connector 6F22 with Cable features: - Cable 15cm long - Battery connector 9V, 6F22 Code PP013 Available Price €0.55
Battery holder 4x AAA 6V Characteristic: - Cable 13cm long - Measurements 49x 52x 13mm - Battery length max 44mm - Compatible batteries (LR03, 24A, R03, RX03, MN2400, AM4, UM4) Code PP001 Available Price €1.19
Battery Holder 6x AA with DC Connector 9V LR06 Ideal to power your Arduino board.Battery Holder 6x AA with DC Connector 9V LR06 features:- Cable 12cm long,- Measures 90x 55x 15mm,- Max 50mm pile length,- Compatible batteries (LR06, R06, MN1500, AM3, UM3, HP7). Code PP008 Available Price €1.85
Battery holder 2x AA 3V Battery holder 2x AA 3V features: - Cable 15cm long - Measurements 59x 33x 16mm - Compatible batteries (LR06, R06, MN1500, AM3, UM3 , HP7) Code PP002 Available Price €0.99
Battery holder 2x 18650 3,7V Parallel Lithium Battery Instruction: - The drawing of the polarities is not correct, it is wrong - Put the batteries in parallel Characteristic: - Cable 15cm long - Measures 74x42x 20mm - Weight: 10 gr. (Approx.) - Stack length max 67mm Code PP016 Available Price €1.85
Battery holder 1x 18650 3.7V Power cable Characteristic: - Cable 15cm long - Measurements 74x21x 19mm - Weight: 8 gr. (approx.) - Stack length max 67mm Code PP014 Available Price €0.99
Battery holder 4x AA 6V LR06 Battery holder 4x AA 6V LR06 features: - Cable 13cm long - Measurements 62x56x 16mm - Battery length max 50mm - Compatible batteries ( LR06, R06, MN1500, AM3, UM3, HP7) Code PP003 Available Price €1.49
Battery holder 2x 18650 3,7V Parallel Lithium Battery Instruction: - The drawing of the polarities is not correct, it is wrong - Put the batteries in parallel Characteristic: - Cable 15cm long - Measures 74x42x 20mm - Weight: 10 gr. (Approx.) - Stack length max 67mm Code PP016 Available Price €1.85
4x 18650 3.7V Parallel Lithium Battery 4x 18650 3.7V Parallel Lithium Battery features: - Cable 10cm long - Measures 80x76x 20mm - Stack length max 67mm Code PP017 Available Price €2.89
Battery Holder 6x AA LR06 Ideal to power your Arduino board.Battery Holder 6x AA LR06 features:- Cable 12cm long,- Measures 90x 55x 15mm,- Max 50mm pile length,- Compatible batteries (LR06, R06, MN1500, AM3, UM3, HP7). Code PP007 Available Price €1.75
2x AAA 3V battery holder for Micro:bit Weight: 12.7g Box size: 62 * 25 * 10 mm Code PP037 Available Price €1.99
Lithium Battery Holder Button 3V CR1220 THT PCB Lithium Battery Holder Button 3V CR1220 THT PCB features: - Material: - Contact: Phosphor Bronze- Electric: - Type: THT - Contact Resistance: 30 Milliohms Max - Insulation Resistance: 1000 Mega Ohms Min - Dielectric Voltage: 500V AC one sec level - Operating Temperature: -25 „ƒ - 85 „ƒ- Suitable for Computer Memory, Power transfer, Communications Power System, PC Application, Armamentarium, Motherboard Code PP033 Available Regular price €1.19 -€0.20 Price €0.99
5x 9v Battery Adapter Connector 6F22 with Cable Ideal to power your Arduino board through the power input. 5x 9v Battery Adapter Connector 6F22 with Cable features: - Cable 15cm long - Battery connector 9V, 6F22 Code PP013 Available Price €0.55
Battery Holder 6x AA with DC Connector 9V LR06 Ideal to power your Arduino board.Battery Holder 6x AA with DC Connector 9V LR06 features:- Cable 12cm long,- Measures 90x 55x 15mm,- Max 50mm pile length,- Compatible batteries (LR06, R06, MN1500, AM3, UM3, HP7). Code PP008 Available Price €1.85
Battery holder 1x 18650 PCB mount 18650 battery base for soldering to PCB. Characteristic: - Measurements 78x 20x 21mm - Weight: 10 gr. ( approx.) - Stack length max 67mm Code PP053 Available Regular price €1.99 -€0.30 Price €1.69