Pulley GT2 16 Teeth 6mm Aluminium Pulley 3D Printer Reprap Pulley GT2 16 Teeth 6mm Aluminium Pulley 3D Printer Reprap features: - Number of teeth: 16 - Pitch: 2mm - Material: aluminum alloy - Outside diameter: 13mm - Inner hole: 5mm - Use with strap: 6mm - Quantity: 1 unit of 16 teeth GT2 pulley, 6mm wide and 2 studs - Ideal for fix on the axis of the motors of your 3D printer Code I0004 Available Price €1.94
BC557B 50V PNP Transistor 100mA 0.1A TO-92 Product Category: Bipolar Transistor, PNP BC557B 50V PNP Transistor 100mA 0.1A TO-92 features: - Package / Case: TO-92 - Quantity: 25 units - Collector-base voltage VCBO: 50V - Collector-emitter voltage VCEO: 45V - VEBO emitter-base voltage: 6V - Continuous collector current: 100mA - DC MAX collector current: 200mA - Maximum power dissipation: 500mW Code T0044 Available Price €0.04
Arduino compatible UNO R3 board - It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features: - Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal - Microprocessor: ATmega328 - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6-20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328 - SRAM 2 KB - Atmega328 Code B0009 Backorder Price €12.95
Arduino Uno R3 Arduino UNO is the best board to start your experience with electronics and programming. If this is your first experience with the platform, UNO is the most robust board you can start with. UNO is the most widely used and documented board in the entire Arduino family. Its power ensures ATmega 328p microcontroller, the board is equipped with 14 digital pins, and 6 analog Code BAR66 Available Price €23.99
2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino 2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino features:- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator: For each channel- Dimensions: 40x 50mm- Has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL004 Available Price €3.15
Heat Shrinkable Tube 5 Colors 3 Meters Package Heat Shrinkable Tube 5 Colors 3 Meters Package features: - Heat shrink tubing is used to connect electrical cables, isolate resistor and capacitor points, mark and protect cables Electrical, protect metal bars or tubes against corrosion and protect antennas. - These heat shrink tubes are very flexible and of high quality. Made in EU - Different sizes of 20 cm each are delivered: * 1,6mm: black, brown, red, yellow, orange * 2,4mm: black, brown , red, yellow, blue * 3,2mm: black, brown, red, yellow, blue - Quantity: 15 units - Material: polyolefin - Shrinkage ratio: 2: 1 (maximum reduce to 1/2 of its supplied diameter) - Minimum shrinkage temperature: 115 ° C maximum 200 ° C Code K0047 Available Price €1.95
MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V High power digital servo, better precision than the MG995. MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V features: - Operating voltage: 4.8 V to 7.2 V- Consumption: 100mA- Torque max.: 12kg / cm (6V)- Operating speed: 0.22sec / 60degree (4.8V), 0.19sec/60degree (6V)- Max. Radio: 180ºC- Temperature range: 0-55 degrees- Weight: 55 g- Cable length: 29cm- Dimensions: 54 x38x 20 mm- Servo connector: JR (JR and Futaba adaptable) Code R0016 Available Price €8.95
M3 Nylon Separator set 120pcs 120x M3 Nylon Separator features: - Hexagonal M3 made of nylon for screws and fastenings on PCB boards, model aircraft, DIY projects - Can be used in prototyping and robotics projects - Box dimension: 128x 66x 24mm - Quantity: 120 units - Color: white Code H0049 Available Price €7.95
A4988 + Stepstick Radiator Stepper Motor Reprap Stepstick A4988 controller Driver for stepper motors Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield A4988 + Stepstick Radiator Stepper Motor Reprap features: - Minimum operating voltage: 8 V - Operating voltage maximum: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0014 Available Price €2.25
Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features: - Superior performance of MOSFET- Maximum current - up to 30A (heat sink)- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series- To control - 5-24V digital signal Code I0093 Available Price €10.49
IRL3803 Mosfet Transistor TO 220 N-Channel 30V 140A IRL3803 Mosfet Transistor TO 220 N-Channel 30V 140A features: - For Hot Bed Ramps- Package: TO-220- Quantity: 1 unit with heatsink and screw Code I0092 Available Price €2.44
Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 features: - 100% brand new and high quality - Optical detector: TCST2103 - Length cable: 50cm - Size: 32mm x 10mm Code I0024 Available Price €1.49
Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Last items in stock Price €5.10
Printer Heating Controller MKS Mos25 for Heatbed Extruder MOS Module MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply. Code I0181 Available Regular price €8.49 -10% Price €7.64
5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine 5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine features: - Compatible with MACH3, Linux CNC (EMC2) etc. CNC parallel control software. - Designed for single axis CNC single phase stepper controller controller: M542, MA860H, 2M542, DM860 etc. - Stepper motor controller drivers 5 axis maximum support. - Wide input voltage range: 12-24V and with anti-reverse function. - USB power supply and peripheral power phase are separated to protect computer security - All signals are opto-isolated, which can protect the security of your computer. - 5 input interface to define limit, emergency stop, cutter alignment, etc. - A relay output control interface, accessed by spindle motor or air pump, water pump, etc. Code I0124 Available Price €9.49
TB6600 4.5A Single Axis CNC Controller The output current of this controller is infinitely adjustable to meet the various requirements of your application.It has an automatic half-current function and a semi-automatic flow switch is also available, easy to use.Its 6N137 high speed optical coupling ensures high speed without losing step printed on the rear panel subdividing the configuration instructions.Its large heat sink allows good quality cooling.The output is protected against short circuits. TB6600 4.5A Single Axis CNC Controller features: - Operating voltage DC 10V-45V- Maximum nominal output: 4.5 A- DC32V switching power is recommended- 6N137 high speed optical coupling, ensure high speed without losing step Code I0151 Available Price €13.90
A4988 + RepRap Radiator A4988 + RepRap Radiator features: - Minimum operating voltage: 8 V - Maximum operating voltage: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0023 Available Price €2.25
UNO R3 Atmega 328P + CNC Shield + 4x A4988 Stepstick Contented:- 1x UNO R3 Atmega 328P 16U2 Compatible with Arduino- 1x CNC Shield V3- 4x A4988 Drivers- 4x Heatsinks for A4988- USB Cable- Jumpers Code I0002 Backorder Regular price €24.94 -€2.80 Price €22.14
A4988 + Stepstick Radiator Stepper Motor Reprap Stepstick A4988 controller Driver for stepper motors Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield A4988 + Stepstick Radiator Stepper Motor Reprap features: - Minimum operating voltage: 8 V - Operating voltage maximum: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0014 Available Price €2.25
Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features: - Superior performance of MOSFET- Maximum current - up to 30A (heat sink)- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series- To control - 5-24V digital signal Code I0093 Available Price €10.49
IRL3803 Mosfet Transistor TO 220 N-Channel 30V 140A IRL3803 Mosfet Transistor TO 220 N-Channel 30V 140A features: - For Hot Bed Ramps- Package: TO-220- Quantity: 1 unit with heatsink and screw Code I0092 Available Price €2.44
Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 features: - 100% brand new and high quality - Optical detector: TCST2103 - Length cable: 50cm - Size: 32mm x 10mm Code I0024 Available Price €1.49
Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Last items in stock Price €5.10
Printer Heating Controller MKS Mos25 for Heatbed Extruder MOS Module MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply. Code I0181 Available Regular price €8.49 -10% Price €7.64
5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine 5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine features: - Compatible with MACH3, Linux CNC (EMC2) etc. CNC parallel control software. - Designed for single axis CNC single phase stepper controller controller: M542, MA860H, 2M542, DM860 etc. - Stepper motor controller drivers 5 axis maximum support. - Wide input voltage range: 12-24V and with anti-reverse function. - USB power supply and peripheral power phase are separated to protect computer security - All signals are opto-isolated, which can protect the security of your computer. - 5 input interface to define limit, emergency stop, cutter alignment, etc. - A relay output control interface, accessed by spindle motor or air pump, water pump, etc. Code I0124 Available Price €9.49
TB6600 4.5A Single Axis CNC Controller The output current of this controller is infinitely adjustable to meet the various requirements of your application.It has an automatic half-current function and a semi-automatic flow switch is also available, easy to use.Its 6N137 high speed optical coupling ensures high speed without losing step printed on the rear panel subdividing the configuration instructions.Its large heat sink allows good quality cooling.The output is protected against short circuits. TB6600 4.5A Single Axis CNC Controller features: - Operating voltage DC 10V-45V- Maximum nominal output: 4.5 A- DC32V switching power is recommended- 6N137 high speed optical coupling, ensure high speed without losing step Code I0151 Available Price €13.90
A4988 + RepRap Radiator A4988 + RepRap Radiator features: - Minimum operating voltage: 8 V - Maximum operating voltage: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0023 Available Price €2.25
UNO R3 Atmega 328P + CNC Shield + 4x A4988 Stepstick Contented:- 1x UNO R3 Atmega 328P 16U2 Compatible with Arduino- 1x CNC Shield V3- 4x A4988 Drivers- 4x Heatsinks for A4988- USB Cable- Jumpers Code I0002 Backorder Regular price €24.94 -€2.80 Price €22.14