Motor Support for Arduino Smart Car the robot car motor holder and assembly accessories Code R0050 Available Price €0.79
M18 Inductive Proximity Sensor M18 Inductive Proximity Sensor features: - Inductive proximity sensor detection switch LJ18A3-8-Z / BX - NPN DC6-36V - A Often used for 3D printer bed leveling - Cylindrical cable type DC 3 cable type (black, brown, blue) - Inductive sensor type - NPN NO (Normal Open ) - Detecting distance 8mm - DC supply voltage 6-36V - Current output 300mA - Response frequency 0.5KHz - Detects iron / aluminum - Operating temperature -25 ° C to + 70 ° C (Non-freezing condition) - Head diameter 18 mm - Size 6.9 x 2cm - Cable length 90cm Code S0042 Available Price €2.88
Breadboard Power Supply Protoboard 830/400 Points MB102 Ideal for your electronic projects, arduino, but can also be used with other microcontrollers. Breadboard Power Supply Protoboard 830/400 Points MB102 features:- Input voltage supports up to 12V- Selectable 3.3V or 5V- USB input or standard DC 2.1 x5.5mm connector- Maximum current 700mA- It fits perfectly on the MB-102 breadboard feeding the two lateral buses- Weight: 15 gr. (approx.) Compatible only with MB-102 type plates Code A0003 Available Price €1.61
Protoboard Breadboard 5x7cm Protoboard Breadboard 5x7cm features: -PCB dimension: 5x7cm-Hole diameter: 1mm -Pitch: 2.54mm-Bakelite with copper fields Code PB021 Available Price €0.49
Resistor 10K Ohm 5% 0,25W 1/4W Resistor 10K Ohm 5% 0,25W 1/4W features:-10K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0021 Available Price €0.07
2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino 2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino features:- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator: For each channel- Dimensions: 40x 50mm- Has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL004 Available Regular price €2.60 -€0.50 Price €2.10
10x Female-Male Cables 20cm Jumpers Dupont 10x Female-Male Cables 20cm Jumpers Dupont features: -Length: 20cm-Quantity: 10 cables-Connectors have male and female header contacts at either end-Compatible with male and female connectors 2,54mm-High quality and good working conditions-Easy to install and use Code K0009 Available Price €1.40
10x Photoresistor GL5539 LDR 50k - 100k Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:- Model: GL5539- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 50-100KΩ- Resistance with darkness (0lux): 5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0013 Available Price €0.12
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Available Price €6.53
Arduino Pro PORTENTA H7 The Arduino Portenta H7 represents a new family of chips designed for IoT applications. The board uses the STM32H747 microcontroller equipped with Cortex-M7 and Cortex-M4 cores, which allows it to run programs written in Arduino®, MicroPython or JavaScript. In addition, the Arduino Portent H7 is characterised by high performance and at the same time energy efficiency. Code ABX42 Available Price €104.12
Screw Shield V1 for Arduino UNO y MEGA Screw Shield V1- Arduino ScrewShield UNO y MEGA features: Screw Shield V1 allows: - Being punctured directly to an Arduino Uno, Mega, Leonardo plate- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more. Code M0173 Available Price €3.26
USB Host Shield Google Android ADK UNO Mega 2560 USB Host Shield Google Android ADK UNO Mega 2560 features: Shield ADK USB allows: - Communication with other USB devices, to build their own mobile accessories- Create projects that require USB Host functionality- Supports USB 2.0, Android ADK- It can also be used with any device equipped with SPI interface- Compatible with Android devices: v2.3.4 and above- USB Host with support for HUB protocol Code M0005 Last items in stock Price €16.12
MyoWare Shield - Mini protoboard for MyoWare sensor Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid. Code SP070 Last items in stock Price €2.72
SparkFun WiFi Shield - ESP8266 The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on. Code SP006 Last items in stock Price €18.17
MyoWare Power Shield MyoWare Power Shield is designed to use two standard CR2032 coin cell batteries to power the MyoWare muscle sensor. These will be connected in parallel for extended capacity at a nominal 3.0V. Code SP071 Backorder Price €5.36
Sensor Cable - Electrode Pads (3 connector) This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads. Code SP075 Available Price €7.43
CNC Shield Expansion Plate + 4x A4988 Stepstick 3D Printer A CNC expansion board kit and 4 stepsticks A4988 for 3D printer. See each component in the product description for details. Code I0105 Available Price €8.55
L293D STM Module Expansion Board 2 Motors - 25V/0.6A The L293D motor controller allows you to control two DC motors or one stepper motor using Arduino kits. The system allows you to adjust the direction and rotational speed of motors with a current consumption of up to 600 mA and a supply voltage from 4.5 V to 25 V. Code M0108 Available Price €3.79
TFT LCD Expansion Board Adapter 34pins V3.0 3.2" 4.3" 5.0" Shield Mega 2560 TFT LCD 34pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0006 Available Price €6.53
Arduino Pro PORTENTA H7 The Arduino Portenta H7 represents a new family of chips designed for IoT applications. The board uses the STM32H747 microcontroller equipped with Cortex-M7 and Cortex-M4 cores, which allows it to run programs written in Arduino®, MicroPython or JavaScript. In addition, the Arduino Portent H7 is characterised by high performance and at the same time energy efficiency. Code ABX42 Available Price €104.12
Screw Shield V1 for Arduino UNO y MEGA Screw Shield V1- Arduino ScrewShield UNO y MEGA features: Screw Shield V1 allows: - Being punctured directly to an Arduino Uno, Mega, Leonardo plate- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more. Code M0173 Available Price €3.26
USB Host Shield Google Android ADK UNO Mega 2560 USB Host Shield Google Android ADK UNO Mega 2560 features: Shield ADK USB allows: - Communication with other USB devices, to build their own mobile accessories- Create projects that require USB Host functionality- Supports USB 2.0, Android ADK- It can also be used with any device equipped with SPI interface- Compatible with Android devices: v2.3.4 and above- USB Host with support for HUB protocol Code M0005 Last items in stock Price €16.12
MyoWare Shield - Mini protoboard for MyoWare sensor Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid. Code SP070 Last items in stock Price €2.72
SparkFun WiFi Shield - ESP8266 The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on. Code SP006 Last items in stock Price €18.17
MyoWare Power Shield MyoWare Power Shield is designed to use two standard CR2032 coin cell batteries to power the MyoWare muscle sensor. These will be connected in parallel for extended capacity at a nominal 3.0V. Code SP071 Backorder Price €5.36
Sensor Cable - Electrode Pads (3 connector) This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads. Code SP075 Available Price €7.43
CNC Shield Expansion Plate + 4x A4988 Stepstick 3D Printer A CNC expansion board kit and 4 stepsticks A4988 for 3D printer. See each component in the product description for details. Code I0105 Available Price €8.55
L293D STM Module Expansion Board 2 Motors - 25V/0.6A The L293D motor controller allows you to control two DC motors or one stepper motor using Arduino kits. The system allows you to adjust the direction and rotational speed of motors with a current consumption of up to 600 mA and a supply voltage from 4.5 V to 25 V. Code M0108 Available Price €3.79