Slide Linear Potentiometer 10K OHM kΩ

Protection box for Arduino UNO R3 made of high quality plastic material. Transparent Plastic Housing for Arduino Uno R3 features:
- Compatible with Arduino UNO
- Material: transparent acrylic
- External dimensions: 75x 60x 15mm

This small 10-DOF sensor module GY-91 is more compact than the GY-80 module.
The module uses a unique MPU-9250 chip combination with built-in 3-axis gyroscope, 3-axis accelerometer, digital compass and BMP280 enhanced barometric pressure sensor.
The MPU-9250, delivered in a 3x3x1mm QFN package, is the smallest 9-axis MotionTracking device in the world and incorporates the latest InvenSense design innovations, allowing dramatically reduced chip size and power consumption, while improving the performance and the cost. Enhancements include low-power accelerometer mode support with only 6.4μA of and provides improved 16-bit compass data resolution (0.15 μT per LSB).

Red Laser Module 650nm 5mW Head Point Adjustable Focal Length features:
- Type: red laser diode
- Laser type: point
- Adjustable Focus
- Wavelength: 650nm
- Output power: 5mW
- Operating voltage: 4.5-5V
- Operating intensity: <40mA
- Operating temperature: -30ºC to 60ºC
- Dimensions of the emitter: Φ12x35mm
- Cable length: 130mm

Battery holder 4x AA 6V LR06 features:
- Cable 13cm long
- Measurements 62x56x 16mm
- Battery length max 50mm
- Compatible batteries ( LR06, R06, MN1500, AM3, UM3, HP7)

Fan 12V 2x 3D Printer Cables features:
- Voltage: 12V
- Consumption: 65mA
- Speed: 3800rpm -5600rpm - Noise level: 25dB ± 10%
- Screw diameter: 4.5mm
- Service Life Time: 35000 hours
- Operating temperature: -10 ° C to 65 ° C
- Cable length: 11cm
- Dimensions: 40mm x 40mm x 10mm

Blue 2 pole PCB mount screw terminal 5.08mm pitch Printed Circuit Board Terminal 3 poles 5.08mm pitch features:
Number of Contacts: 3
Pitch: 5.08mm
Number of Rows: 1
Mounting Type: PCB
Gender: Male
Allowable Section: 1.5mm2 (22- 14 AWG)
Termination method: screw
Type: screw terminal block
Nominal current: 16A
Nominal voltage: 250V
Color: blue
Material: Nylon 66
Depth: 10mm
Width: 7.5mm
Length: 10mm

This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos.
It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity.
PCA9685 digital servo motor controller 16 channel PWM features:

- Supply voltage: 3-5 VDC,
- Maximum motor voltage: 6 VDC,
- Number of channels: 16,
- Resolution per channel: 12 bits,
- Interface: I2C,
- Working frequencies: 40-1000 Hz,
- PCB size: 62.3x25.3mm .

Limit Switch with Wheel - 5A 250 Vac - 1 switched - Arduino features:
-Micro KW12-3 on / off switch
-Max Current: 5A -AC voltage: 125-250V
-Operating temperature: -40 to 70 degrees C
-Quantity: 2 units