Mini VNH3SP30 Stepper Motor Driver Module 30A Mini VNH3SP30 Stepper Motor Driver Modules capable of handling a high consumption motor. Code R0020 ✗ Out-of-Stock Price €4.01
10x Photoresistor GL5539 LDR 50k - 100k Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:- Model: GL5539- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 50-100KΩ- Resistance with darkness (0lux): 5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0013 Available Price €0.12
CNC Shield Expansion Plate V3 Engraver 3D Printer CNC shield for arduino works as a controller for CNC type milling machines, 3D printers, laser cutters . CNC Shield Expansion Plate V3 Engraver 3D Printer features: 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible 4 support axes X, Y, Z, A 2 limit switches for each axis (6 in total) Code I0011 Available Price €2.27
Boost Buck Step Up-Down Automatic Converter Descripción:This is a powerful, efficient step-up (boost) and step-down (buck) switching voltage converter. It will automatically change between boosting and bucking to maintain a stable output voltage, regardless of the input.The output is set with a multi-turn potentiometer.Boost Buck Step Up-Down Automatic Converter features:- IC Chip: LM2577S-ADJ and LM2596S-ADJ - Module Properties: non-isolated Boost Buck constant current, constant voltage module (CC CV) charging module- Scope: High-power constant current LED driver.- Battery charger (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charger, solar panels, wind generators. Code A0017 Available Price €7.84
40x Female Male 10cm 40x Female Male 10cm features: - Length: 10cm - Quantity: 40 cables - Compatible with 2.54mm male connectors - High quality and good working conditions - Easy to install and use Code K0106 Available Price €1.64
Battery charger BMS 3,7-96V 10A - Automatic charge controller module This 3.7-96V 10A battery charger is an automatic charge controller module that prevents the battery from dropping below a voltage level, the value of which is adjustable. It is suitable for 1.5 to 120V batteries, as using it will save time and energy. Code A0130 Available Price €9.01
USB 2.0 A Serial Port Cable Adapter DB9 RS232 Series An RS232 serial port to your PC through the USB port USB 2.0 A Serial Port Cable Adapter DB9 RS232 Series features: - CH341 driver- Supported OS: WinME, Win2003, Win XP, Vista, Win 7, Linux, MAC OS9.0/OSX- High quality, shielded cable- Power and data in the same cable, does not require more adapters- Compatible USB interface 1.1 and 2.0- Support up to 1 mega data transfer- Length 73cm The adapter allows you to connect a computer with: - Electric meters- Decoders, programmers- Cash registers- Satellite TV- Control panels- Mobile phones- Diagnostic interfaces for cars- The administration of Cisco routers Code C0010 Available Price €2.72
L9110 Fan Motor Propeller Module 5V The module for DIY Arduino hobbyMotor driver L9110 for Arduino, Smart Car, RoboticsSmall magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features: - Operating voltage: 5V- PCB dimension: 3.5 x 2.6cm- Double red propeller- Blade length 75mm- Weight: 6 g- Quantity: 1x DC motor 1x double helix Code M0132 Available Regular price €2.44 -€0.50 Price €1.94
IRL3803 Mosfet Transistor TO 220 N-Channel 30V 140A IRL3803 Mosfet Transistor TO 220 N-Channel 30V 140A features: - For Hot Bed Ramps- Package: TO-220- Quantity: 1 unit with heatsink and screw Code I0092 Last items in stock Price €2.06
Printer Heating Controller MKS Mos25 for Heatbed Extruder MOS Module MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply. Code I0181 Available Regular price €6.90 -10% Price €6.21
Ramps 1.6 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0194 ✗ Out-of-Stock Price €8.18
Zum Scanner Expansion Board 3D DIY Zum Scanner Expansion Board 3D DIY features: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- 3D Scanner Ciclop is an open source project created by bq- Zum shield DIY 3D scanner, which used to control the stepper motors, the LDR sensor and the laser- The complete electronic package that includes a ZUM Scan Shield, an A4988 Stepper Driver and an Arduino UNO R3 Board Code I0056 ✗ Out-of-Stock Price €10.32
A4988 + RepRap Radiator A4988 + RepRap Radiator features: - Minimum operating voltage: 8 V - Maximum operating voltage: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0023 Available Price €1.57
Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features: - Superior performance of MOSFET- Maximum current - up to 30A (heat sink)- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series- To control - 5-24V digital signal Code I0093 Available Price €7.84
Mechanical End of Career CNC Ramps1.4 3D Printer Mechanical End of Career CNC Ramps1.4 3D Printer features: - Mechanical limit switch, Endstop - 100% brand new and high quality - 1A 125V AC switch - Cable length: 70cm - PCB dimensions: 40mm x 15mm Code I0029 Available Price €1.23
3D Zum Scan Shield + UNO R3 CH340 + A4988 Stepper Feature of 3D Zum shield: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- Content: - 1x Zum Shield 3D - 1x UNO R3 Compatible Arduino - 1x Controller A4988 - 1x Male pin strip - 1x Heatsink for A4988 - 1x USB cable - Jumpers Code I0057 ✗ Out-of-Stock Price €17.27
A4988 + Stepstick Radiator Stepper Motor Reprap Stepstick A4988 controller Driver for stepper motors Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield A4988 + Stepstick Radiator Stepper Motor Reprap features: - Minimum operating voltage: 8 V - Operating voltage maximum: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0014 Available Price €1.57
Ramps 1.5 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.5 for 3D printer. Includes jumpers. RAMPS plate is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0193 Available Price €4.95
IRL3803 Mosfet Transistor TO 220 N-Channel 30V 140A IRL3803 Mosfet Transistor TO 220 N-Channel 30V 140A features: - For Hot Bed Ramps- Package: TO-220- Quantity: 1 unit with heatsink and screw Code I0092 Last items in stock Price €2.06
Printer Heating Controller MKS Mos25 for Heatbed Extruder MOS Module MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply. Code I0181 Available Regular price €6.90 -10% Price €6.21
Ramps 1.6 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0194 ✗ Out-of-Stock Price €8.18
Zum Scanner Expansion Board 3D DIY Zum Scanner Expansion Board 3D DIY features: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- 3D Scanner Ciclop is an open source project created by bq- Zum shield DIY 3D scanner, which used to control the stepper motors, the LDR sensor and the laser- The complete electronic package that includes a ZUM Scan Shield, an A4988 Stepper Driver and an Arduino UNO R3 Board Code I0056 ✗ Out-of-Stock Price €10.32
A4988 + RepRap Radiator A4988 + RepRap Radiator features: - Minimum operating voltage: 8 V - Maximum operating voltage: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0023 Available Price €1.57
Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features: - Superior performance of MOSFET- Maximum current - up to 30A (heat sink)- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series- To control - 5-24V digital signal Code I0093 Available Price €7.84
Mechanical End of Career CNC Ramps1.4 3D Printer Mechanical End of Career CNC Ramps1.4 3D Printer features: - Mechanical limit switch, Endstop - 100% brand new and high quality - 1A 125V AC switch - Cable length: 70cm - PCB dimensions: 40mm x 15mm Code I0029 Available Price €1.23
3D Zum Scan Shield + UNO R3 CH340 + A4988 Stepper Feature of 3D Zum shield: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- Content: - 1x Zum Shield 3D - 1x UNO R3 Compatible Arduino - 1x Controller A4988 - 1x Male pin strip - 1x Heatsink for A4988 - 1x USB cable - Jumpers Code I0057 ✗ Out-of-Stock Price €17.27
A4988 + Stepstick Radiator Stepper Motor Reprap Stepstick A4988 controller Driver for stepper motors Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield A4988 + Stepstick Radiator Stepper Motor Reprap features: - Minimum operating voltage: 8 V - Operating voltage maximum: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0014 Available Price €1.57
Ramps 1.5 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.5 for 3D printer. Includes jumpers. RAMPS plate is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0193 Available Price €4.95