LM35DZ Temperature Sensor TO-92 LM35 Temperature Sensor LM35DZ TO92 features:- The output is linear and each degree Celsius equals 10 mV- Power supply from 4 to 30 Vdc- Connection through analog input- Temperature range from 0ºC to 100ºC- Linearity +10 mV / ºC- Quantity: 1 unit Code S0016 Available Price €3.39
Electric Paint Tube of 10ml Draw circuits, sensors or simply replace wires with this electrically conductive paint. Stimulate children's creativity and manual skills, with the assembly of simple and safe circuits, thanks to this conductive paint. This Electric Paint is a conductive paint that can be used mainly for repairing breaks, cold welding or drawing circuits on a small scale. It is as easy as squeezing the tube, drawing a line of paint on a surface, connecting components and power, and you have an electric circuit in a totally original way. Code RA118 Available Regular price €19.99 -€1.00 Price €18.99
Motor Nema 17 4.28kg 17HS4401 It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 4.28 kg/cm. It comes with a 1m cable. We have the best stepper motors at the best prices! Code I0020 Available Price €13.50
Rechargeable battery 9V 6F22 Ni-MH 250 mAh Ready to Use Rechargeable battery 9V 6F22 Ni-MH 250 mAh Ready to Use features: Code PP049 Available Price €5.99
SW-520D Vibration Metal Tilt Sensor Detects changes in the sensor angle and returns to the digital value. 5x SW-520D Vibration Metal Tilt Sensor features: - Contact resistance: Code S0020 Available Price €0.45
Resistor 1M Ohm 5% 0,25W 1/4W Resistor 1M Ohm 5% 0,25W 1/4W features:-1M Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0031 Available Price €0.08
Adhesive Thermal Paste Glue 10g CPU Totally new and of high quality.Dissipate the heat of the computer by refrigerating it effectively.It is used to attach passive dissipaters to graphic memories and chip plates and LED diodes.Make sure to put the components correctly, once it has dried it will not be able to detach. Adhesive Thermal Paste Glue 10g CPU features: - Color white- Surface drying time [25 ° C, min]: 2- 8- Hardness: 45 -75- Tensile strenght (Mpa): 2.0- Elongation (%): 100- Thermal Conductivity W / mk:> 1,0- Volume Resistance (c-in / W): <2.0 x 10 * 15- Dielectric strength (KV / mm): 20- Dielectric Constant: 3.0- Dielectric loss factor (60Hz): 0.003- Operating temperature (max): 200 ° C Code Q0006 Available Price €3.95
BD137 Plastic Medium-Power Silicon NPN Transistors pack 5ps BD137 Plastic Medium-Power Silicon NPN Transistors pack 5ps features: Material: Silicon Polarity: N-P-N Encapsulated: TO 126 Audio amplifier, driver VCBO collector-base voltage: 60V VCEO collector-emitter voltage: 60V VEBO emitter-base voltage: 5V Collector continuous current: 1.5A Typical gain of direct current. hfe: 40-160Maximum power dissipation: 12.5 Watt if T <= 25ºC Working frequency: 250 MHzTypical gain of direct current. hfe: 40-160 Code T0074 Available Price €0.99
A4988 + Stepstick Radiator Stepper Motor Reprap Stepstick A4988 controller Driver for stepper motors Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield A4988 + Stepstick Radiator Stepper Motor Reprap features: - Minimum operating voltage: 8 V - Operating voltage maximum: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0014 Available Price €2.25
Ramps 1.6 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0194 Last items in stock Price €9.90
TB6600 4.5A Single Axis CNC Controller The output current of this controller is infinitely adjustable to meet the various requirements of your application.It has an automatic half-current function and a semi-automatic flow switch is also available, easy to use.Its 6N137 high speed optical coupling ensures high speed without losing step printed on the rear panel subdividing the configuration instructions.Its large heat sink allows good quality cooling.The output is protected against short circuits. TB6600 4.5A Single Axis CNC Controller features: - Operating voltage DC 10V-45V- Maximum nominal output: 4.5 A- DC32V switching power is recommended- 6N137 high speed optical coupling, ensure high speed without losing step Code I0151 Available Price €13.90
Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Last items in stock Price €5.10
Printer Heating Controller MKS Mos25 for Heatbed Extruder MOS Module MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply. Code I0181 Available Regular price €8.49 -10% Price €7.64
MKS TMC2208 V2.0 + Heatsink Stepstick Stepper Driver Motor for 3D Printer TMC2208 V2.0 Silent Stepstick Stepper, Motor Controller Module + Heatsink Compared to the TMC2100 module, the TMC2208 controller module emits less heat. Code I0180 Available Price €4.95
Industrial DKC-1A stepper motor controller The controller creates step-by-step motor control functions preset with the latest imported high-speed chip and uses a combination of software and hardware methods to ensure superior anti-jam performance of the controller.It also has reverse polarity protection, overvoltage protection, overcurrent protection, absolute guarantee of safe operation of the controller in a variety of hostile factory environments.Applies to stepper motor control switches, round-trip motion control, fixed speed control. Industrial DKC-1A stepper motor controller features: - Operating voltage: 5-32 VDC- Signal entry point for the lower level entry- Optimization of the acceleration of the S curve- The maximum output frequency can reach 20 KHz Code M0155 Available Price €8.50
Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 features: - 100% brand new and high quality - Optical detector: TCST2103 - Length cable: 50cm - Size: 32mm x 10mm Code I0024 Available Price €1.49
Zum Scanner Expansion Board 3D DIY Zum Scanner Expansion Board 3D DIY features: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- 3D Scanner Ciclop is an open source project created by bq- Zum shield DIY 3D scanner, which used to control the stepper motors, the LDR sensor and the laser- The complete electronic package that includes a ZUM Scan Shield, an A4988 Stepper Driver and an Arduino UNO R3 Board Code I0056 Available Price €12.25
MKS PWC V3.0 power auto-off while finish printing module Auto shut down module for MKS GEN L SKR V1.3 MKS PWC automatically turning off after the printing. It helps in the cases like the unexpected power off or you have to leave during the printing, and other similar issues. Code I0187 Available Regular price €18.49 -€3.00 Price €15.49
A4988 + Stepstick Radiator Stepper Motor Reprap Stepstick A4988 controller Driver for stepper motors Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield A4988 + Stepstick Radiator Stepper Motor Reprap features: - Minimum operating voltage: 8 V - Operating voltage maximum: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0014 Available Price €2.25
Ramps 1.6 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0194 Last items in stock Price €9.90
TB6600 4.5A Single Axis CNC Controller The output current of this controller is infinitely adjustable to meet the various requirements of your application.It has an automatic half-current function and a semi-automatic flow switch is also available, easy to use.Its 6N137 high speed optical coupling ensures high speed without losing step printed on the rear panel subdividing the configuration instructions.Its large heat sink allows good quality cooling.The output is protected against short circuits. TB6600 4.5A Single Axis CNC Controller features: - Operating voltage DC 10V-45V- Maximum nominal output: 4.5 A- DC32V switching power is recommended- 6N137 high speed optical coupling, ensure high speed without losing step Code I0151 Available Price €13.90
Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Last items in stock Price €5.10
Printer Heating Controller MKS Mos25 for Heatbed Extruder MOS Module MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply. Code I0181 Available Regular price €8.49 -10% Price €7.64
MKS TMC2208 V2.0 + Heatsink Stepstick Stepper Driver Motor for 3D Printer TMC2208 V2.0 Silent Stepstick Stepper, Motor Controller Module + Heatsink Compared to the TMC2100 module, the TMC2208 controller module emits less heat. Code I0180 Available Price €4.95
Industrial DKC-1A stepper motor controller The controller creates step-by-step motor control functions preset with the latest imported high-speed chip and uses a combination of software and hardware methods to ensure superior anti-jam performance of the controller.It also has reverse polarity protection, overvoltage protection, overcurrent protection, absolute guarantee of safe operation of the controller in a variety of hostile factory environments.Applies to stepper motor control switches, round-trip motion control, fixed speed control. Industrial DKC-1A stepper motor controller features: - Operating voltage: 5-32 VDC- Signal entry point for the lower level entry- Optimization of the acceleration of the S curve- The maximum output frequency can reach 20 KHz Code M0155 Available Price €8.50
Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 features: - 100% brand new and high quality - Optical detector: TCST2103 - Length cable: 50cm - Size: 32mm x 10mm Code I0024 Available Price €1.49
Zum Scanner Expansion Board 3D DIY Zum Scanner Expansion Board 3D DIY features: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- 3D Scanner Ciclop is an open source project created by bq- Zum shield DIY 3D scanner, which used to control the stepper motors, the LDR sensor and the laser- The complete electronic package that includes a ZUM Scan Shield, an A4988 Stepper Driver and an Arduino UNO R3 Board Code I0056 Available Price €12.25
MKS PWC V3.0 power auto-off while finish printing module Auto shut down module for MKS GEN L SKR V1.3 MKS PWC automatically turning off after the printing. It helps in the cases like the unexpected power off or you have to leave during the printing, and other similar issues. Code I0187 Available Regular price €18.49 -€3.00 Price €15.49