Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module
  • Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module
  • Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module
  • Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module
  • Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module
  • Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module

Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module

I0093

Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features:
- Superior performance of MOSFET
- Maximum current - up to 30A (heat sink)
- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series
- To control - 5-24V digital signal

Makerbase
5905323237100
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features:


- Superior performance of MOSFET
- Maximum current - up to 30A (heat sink)
- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series
- To control - 5-24V digital signal

Customers who bought this product also bought

HC-SR04 Ultrasonic Sensor Distance Measuring Module

It is very easy to make it work with an Arduino, PIC or any other microcontroller.
In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle.
HC-SR04 Ultrasonic Sensor Distance Measuring Module features:
- Supply voltage: 5V (4.5V- 6V)
- Consumption: 30 mA typical, (35 mA max)
- Interface: VCC , GND, Signal
- Range: 2 cm to 3 meters
- Angle 15º
- LED indicator of measurement in progress
- Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm
- Quantity: 1 unit
Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry:
Automatic robot operation with obstacle detection />

S0007

Price €1.48

5x Push Switch Button B3F Omron Blue Key 12mm

5x Push Switch Button B3F Omron Blue Key 12mm features:

- 5x Push Buttons B3F Omron Key
- Maximum current: 50 mA
- Tension DC: 24V
- Operating force: 1.27N
- Switch terminals: weldable
- Contact: SPST-NO
- Contact resistance: 100M Ohm
- Type of action: Superficial
- Measures: 12x12x7.3mm

K0074

Price €0.17

JST PHR-2 Female 2 PIN 2mm

It is not possible to reverse the polarity by mistake.
JST PHR-2 Female 2 PIN 2mm features:
Manufacturer JST Connector series: PH Connector: plug Connector class: female Type of connector: conduit-board Raster of contactors: 2mm Number of pins: 2 Mechanical mounting: for conduit Voltage Working: 100V Working current: 2A Working temperature: -25 ... 85 ° C Connection version: contactless technical data sheet PH series

K0209

Price €0.23

40x Female-Female Cable 10cm

40x Female-Female Cable 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Dupont female connectors on both ends
- Compatible with 2.54mm male connectors
- High quality and good working conditions
- Easy to install and use

K1005

Price €1.64

Heater Block MK8 NTC 3950 Nozzle 0.4mm 1.75mm

Heater Block MK8 NTC 3950 Nozzle 0.4mm 1.75mm features:
- 3D Printer Extruder
- 0.4mm Nozzle
- 100k 3950 NTC thermistor with cable
- MK8 heater block with 12v / 40W thermal ceramic resistance with cable
- 1.75mm filament stud M6x30mm

I0102

Price €4.54

Adjustable DC Module LM2596 1,25-32V 3A Step Down

3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features:

- Based on the LM2596S-ADJ regulator
- Rectification: Asynchronous
- Output Voltage: 1.25v - 32v DC (adjustable)
- Voltage of Input: 3.2v - 35v DC
- Max Output Current: 3A (with heat sink)
- Ripple at output voltage: 30mV
- Frequency: 150KHz
- Max Conversion Efficiency: 92%
- Load Regulation: ± 0.5%
- Voltage Regulation: ± 2.5%
- Operating Temperature: -40ºC to + 85ºC
- Measurements 43x 21x 14 mm

A0004

Price €1.64

ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino UNO V5.0

ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino UNO V5.0 features:
- To mount your projects in a comfortable and orderly way, access to all the pins of Arduino Uno R3, it has a universal plate and protoboard zone, 5V and Gnd buses, reset pushbutton, pushbutton and 2 general purpose leds, zones for integrated Soic and Dip
- The seamless mini breadboard has 170 connection points.
- You can stick on the shield with its self-adhesive back.

M0016

Regular price €1.82 -€0.21 Price €1.61
€7.84

7,84 tax excl.

1
10 items
Price €7.84

Order until 4pm we will send today
30 days return