USB Cable for Arduino Type A-B

High power digital servo, better precision than the MG995. MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V features:
- Operating voltage: 4.8 V to 7.2 V
- Consumption: 100mA
- Torque max.: 12kg / cm (6V)
- Operating speed: 0.22sec / 60degree (4.8V), 0.19sec/60degree (6V)
- Max. Radio: 180ºC
- Temperature range: 0-55 degrees
- Weight: 55 g
- Cable length: 29cm
- Dimensions: 54 x38x 20 mm
- Servo connector: JR (JR and Futaba adaptable)

The Raspberry Pi 4 Model B is the latest product in the Raspberry Pi family of computers. This product is in the 4GB RAM version, with 2GB (B0068) and 1GB (B0067) versions also on offer.

This Reed switch module uses a small device called a reed switch.
When the device is exposed to a magnetic field, the two ferrous materials inside the switch come together and the switch closes. When the magnetic field is removed the switch opens. The operating mode: - When exposed to a magnetic field the DO output is high
- Power supply: 3.3-5V
- Contact type: SPST-NO (normally open)
- Use temperature: -20ºC to + 80ºC
- Type Output: Digital (1 - 0)
- PCB dimensions: 32 x 14 mm

Characteristic: - Lithium Battery WITHOUT Protection
- Nominal capacity: 2600mAh (discharge of 0.2C, 2.75V)
- Minimum capacity: 2550mAh (0.2C, 2.75V discharge)
- Charging voltage: 4.2 ± 0.05 V
- Nominal voltage: 3.63V
- Charging method: DC-CV (constant voltage with current limited)
- Charging current: standard charge: 1300mA, fast charge: 2600mA
- Charging time: standard charge: 3 hours, fast charge: 2.5 hours
- Max. Charging current: 2600mA (ambient temperature 25 °)
- Max. Discharge current: 5200mA (ambient temperature 25 °)
- Discharge cut-off voltage: 2.75V
- Cell weight: 47.0g maximum
- Cell dimension: Height: 65.00 mm max., Diameter: 18.40 mm max.

The module is based on a touch sensitive IC capacitive touch switch module (TTP223B).
In the normal state, the module produces Low power consumption. When a finger touches the corresponding position, the module output is high, if not touched for 12 seconds, it switches to low power mode. Digital Touch Sensor B21 features:
- Low power consumption
- Input voltage: 2 - 5.5VDC
- Can replace the traditional touch of a button - Four M2 screws diameter 2.2 mm that position the holes for easy installation
- 3-pin control interface:
1- GND
2- VCC
3- Control signal (output pin)
- Power indicators: Bright green LED when the sensor is on

This connector can be used in most modeling projects.
It is ideal for small Lipo and NiMH connection. JST Male Connector 15cm AWG18 features:
- Type: JST male connector for RC BEC Lipo
- Color:
- Black: low power polarity
- Red: high power polarity
- Length: 20cm

This module, which uses the exclusive L298P chip for driving high-power motors, can directly control two DC motors, with a drive current up to 2A. The motor output uses eight-speed Schottky diodes as protection.
The design of the letter allows you to connect directly to the Arduino UNO R3 for easier use. Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM features:
- 1 logical step of the input voltage VD: 5 VDC
- Control of the input voltage VS and control by pulse width modulation:
      - VIN input: 6 - 12 VDC
      - PWRIN input: 4.8 - 35 VDC
- Logic current flow: Iss <36m A
- Operation current management: Io <2 A
- Maximum power dissipation 25W (T = 75 ° C)
- Input of the control signal:

Grove - Wrapper is a kind of wrapper for repairing and protecting Grove modules. It will save you a lot of work in aligning your modules and make it easy for you to display your project.