A4988 + Stepstick Radiator Stepper Motor Reprap

Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.
Run easily with Arduino. Router TB6600 1 Axis 5A Stepper Motor Driver Board features:
- Minimum operating voltage: 12 V
- Maximum operating voltage: 48 V
- Maximum current: ± 5 A
- Maximum power: 240W
- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23
- Control inputs optically isolated
- Step resolution: 200, 400, 1600, 3200
- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 adjustable by interruptor DIP
- Current control: 0.2A/0.6A/1.2A/1.8A/2.5A/3.3A/4.2A/>

The output current of this controller is infinitely adjustable to meet the various requirements of your application.
It has an automatic half-current function and a semi-automatic flow switch is also available, easy to use.
Its 6N137 high speed optical coupling ensures high speed without losing step printed on the rear panel subdividing the configuration instructions.
Its large heat sink allows good quality cooling.
The output is protected against short circuits. TB6600 4.5A Single Axis CNC Controller features:
  - Operating voltage DC 10V-45V
- Maximum nominal output: 4.5 A
- DC32V switching power is recommended
- 6N137 high speed optical coupling, ensure high speed without losing step

TMC2208 V2.0 Silent Stepstick Stepper, Motor Controller Module + Heatsink

Compared to the TMC2100 module, the TMC2208 controller module emits less heat.

MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply.

Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.
Run easily with Arduino. Router TB6600 1 Axis 3.5A Stepper Motor Driver Board features:
- Minimum operating voltage: 9 V
- Maximum operating voltage: 40 V
- Maximum current: ± 3.5 A
- Maximum power: 160W
- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23
- Control inputs 5V optically isolated
- Step resolution: 200, 400, 400, 800, 1600, 3200, 6400
- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 y 1/32 adjustable by interruptor DIP
- Current control: 0.5A/>0A/>

CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer Arduino kit features:
- Content:
* 1x UNO R3 CH340 Compatible with Arduino
* 1x CNC Shield V3
* 4x A4988 Drivers
* 4x Heatsinks for A4988
* Jumpers

The controller creates step-by-step motor control functions preset with the latest imported high-speed chip and uses a combination of software and hardware methods to ensure superior anti-jam performance of the controller.
It also has reverse polarity protection, overvoltage protection, overcurrent protection, absolute guarantee of safe operation of the controller in a variety of hostile factory environments.
Applies to stepper motor control switches, round-trip motion control, fixed speed control. Industrial DKC-1A stepper motor controller features:
- Operating voltage: 5-32 VDC
- Signal entry point for the lower level entry
- Optimization of the acceleration of the S curve
- The maximum output frequency can reach 20 KHz

CNC shield for arduino works as a controller for CNC type milling machines,
3D printers, laser cutters .
CNC Shield Expansion Plate V3 Engraver 3D Printer features:

• 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible
• 4 support axes X, Y, Z, A
• 2 limit switches for each axis (6 in total)

5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine features:
- Compatible with MACH3, Linux CNC (EMC2) etc. CNC parallel control software.
- Designed for single axis CNC single phase stepper controller controller:
M542, MA860H, 2M542, DM860 etc.
- Stepper motor controller drivers 5 axis maximum support.
- Wide input voltage range: 12-24V and with anti-reverse function.
- USB power supply and peripheral power phase are separated to protect computer security
- All signals are opto-isolated, which can protect the security of your computer.
- 5 input interface to define limit, emergency stop, cutter alignment, etc.
- A relay output control interface, accessed by spindle motor or air pump, water pump, etc.

A CNC expansion board kit and 4 stepsticks A4988 for 3D printer. See each component in the product description for details.