Module Relay 5V Light sensor LDR photoresistor This module is a three way switch ( COM, NO and NC ) that uses the intensity of the ambient light to control directly the load at the output. Its adjustment potentiometer allows changing the sensitivity and setting the start threshold of the relay. The relay is energized when it is darker than the threshold. Code RL016 Available Price €1.98
DHT11 Temperature and Humidity Sensor The humidity sensor DHT11 comes in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. DHT11 Temperature and Humidity Sensor features: - Operating voltage: 3 to 5 VDC- Humidity measurement range: 20-95% ± 5% accuracy- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy- Maximum sampling rate: 2 seconds- Working current 2.5mA- Iterfaz 1-wire- Dimensions: 2.3 x1.2x 0.5cm- Quantity: 1 unit Code S0010 ✗ Out-of-Stock Price €2.06
A4988 + RepRap Radiator A4988 + RepRap Radiator features: - Minimum operating voltage: 8 V - Maximum operating voltage: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0023 Available Price €1.57
Side Cutting Pliers 110mm Side Cutting Pliers 110mm features: - This model is not isolated, please use it without current- The tool has an opening spring for greater comfort.- Use to cut soft materials, electronic components, cables, plastic card- Can also be used for welding work Code H0115 ✗ Out-of-Stock Price €4.04
ESP8266 5V WiFi Relay Module AP Remote Control + STA You can easily control any device over the Internet through your phone, computer, etc. The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point). In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters). In STA mode, the relay module is connected to the access point (router) that supplies the network. Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers). You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off. Code W0067 Available Price €7.84
2 Double Side Prototype PCB Board 6x8cm 2 Double Side Prototype PCB Board 6x8cm features: -Thickness of PCB: 1.6mm-Material: high quality FR-4 glass fiber PCB-Presented and numbered on both sides-Top and bottom are identical copper layers-Pads grid (pitch) 2.54mm/0.1", hole diameter 0.9mm Code PB026 Available Price €0.82
Multiplexer 16 Channels CD74HC4067 MUX/DEMUX A multiplexer of this type actually only acts as a switch 16 to a 1.The 4 digital pins are used to set high or low, (binary Y0-Y15) to determine which input pin is connected to pin "Z".The control input S0-S3 is set to low "logic level 0", the signal C0 is connected to the output Z. Multiplexer 16 Channels CD74HC4067 MUX/DEMUX features: - Based on chip CD74HC4067- Analog signal input: Y0-Y15, 16 channels- Analog signal output: Z pin- Digital input, channel control: S0-S3- Module size: approx. 4 x 1.8cm- Package includes:* 1 x CD74HC4067 MUX connection module* 2 x row of soldering pins Code C0006 Available Price €2.88
Push button 6x6x4mm Push button 6x6x4mm features: -Touch Push Tact Switch mini electronic Arduino push button -Measures: 6x6x4.3mm -Quantity: 1 unit Code K0201 Available Price €0.17
L9110 Fan Motor Propeller Module 5V The module for DIY Arduino hobbyMotor driver L9110 for Arduino, Smart Car, RoboticsSmall magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features: - Operating voltage: 5V- PCB dimension: 3.5 x 2.6cm- Double red propeller- Blade length 75mm- Weight: 6 g- Quantity: 1x DC motor 1x double helix Code M0132 Available Regular price €2.44 -€0.50 Price €1.94
Servo Driver for micro:bit, 16-Channel, 12-bit The micro:bit servo driver module, 16 channel, 12 bit, I2C interface. Have you ever had the problem of not having enough micro:bit PWM outputs when trying to create a robotic arm or other robot that requires multiple servos? At times like this a great solution comes to your aid. This servo controller will be the perfect choice. Code WV007 Available Price €18.14
Router TB6560 1 Axis 3A Stepper Motor Driver Board Router TB6560 1 Axis 3A Stepper Motor Driver Board features: - Minimum operating voltage: 10 V- Maximum operating voltage: 35 V (24V recommended)- Maximum current: ± 3 A- Stepper motor · two phases · four phases- Resolution of microsteps: full, 1/2, 1/8, and 1/16- PCB measurements: 75x50 mm- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply- 6N137 high speed optical coupling guarantees high speed without losing steps- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent- Protection circuit to ensure optimal performance- Maximum nominal output: 3 A, peak 3.5A Code I0106 Available Price €6.57
PCA9685 digital servo motor controller 16 channel PWM This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos. It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity. PCA9685 digital servo motor controller 16 channel PWM features: - Supply voltage: 3-5 VDC, - Maximum motor voltage: 6 VDC, - Number of channels: 16, - Resolution per channel: 12 bits, - Interface: I2C, - Working frequencies: 40-1000 Hz, - PCB size: 62.3x25.3mm . Code R0074 Available Price €4.21
Mini VNH3SP30 Stepper Motor Driver Module 30A Mini VNH3SP30 Stepper Motor Driver Modules capable of handling a high consumption motor. Code R0020 ✗ Out-of-Stock Price €4.01
LSC-16 Digital Servo Motor Controller 16 channels LSC-16 Digital Servo Motor Controller 16 channels features: - With current limiting protection. The servo output is isolated from the CPU to prevent increased servo current causing damage to the CPU. - CPU using high performance STM32 single chip microcomputer with ARM Cortex-M3 corer, control High precision 16-channel servo movement, adjustable speed. - 16M high capacity memory, enough for your use! It can contain 230 action groups! Each action group can hold up to 510 actions! - Supports online debugging, no need to install any driver by yourself (Install Drivers Automatically). - 0 ~ 3rd and 12th - 15th servo interface have over current protection! Greatly reducing the risk of burned servo due to locked rotor. Code R0046 Available Regular price €21.32 -€2.00 Price €19.32
Controller TB6612FNG DC PAP motor TB6612FNG controller, double H-bridge controller driver. Allows to control up to 2 current motors continuous or bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. An improved version of the L298N. H-bridges are made up of MOSFET transistors, rather than BJT transistors as in the L298N. The TB6612FNG has better efficiency and smaller dimensions than the L298N. Controller TB6612FNG DC PAP motor features: - Minimum operating voltage: 4.5 V - Maximum operating voltage: 13.5 V (15V max) - Maximum current: ± 3A per channel (1.2 A direct current per channel) - Logic voltage: 5V Code R0002 ✗ Out-of-Stock Price €4.95
L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.It incorporates a switch for the connection and disconnection of the entire module. L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth /> Code M0183 Available Price €3.13
VNH3SP30 Stepper Motor Driver Module 30A Driver capable of handling up to two high consumption motors.We can weld 5mm screw terminals (not included), making it easy to connect other gauge cables. Code R0010 ✗ Out-of-Stock Regular price €12.88 -€2.50 Price €10.38
Mosfet 24V 5A IRF520 PWM controller Mosfet 24V 5A IRF520 PWM controller features: - The IRF520 controller module can control the PWM signal from the Arduino module and adjust the DC voltage of So that we can control the speed of the DC motor, the brightness of the bulb, the LEDs, the heater. - The built-in IRF520 N-MOSFET transistor - Operating voltage: 3.3V -5V ( compatible with ARDUINO Raspberry PI) - Charging voltage: 0-24V - Charging current: up to 5A (more than 1A, the system must be equipped with a heat sink point) - 60W max power (more than 10W must be equipped with a heat sink) - Terminalblock connectors - LED indicating the presence of power - Dimensions: 33x24mm Code A0022 Available Regular price €2.06 -€0.50 Price €1.56
L9110 Fan Motor Propeller Module 5V The module for DIY Arduino hobbyMotor driver L9110 for Arduino, Smart Car, RoboticsSmall magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features: - Operating voltage: 5V- PCB dimension: 3.5 x 2.6cm- Double red propeller- Blade length 75mm- Weight: 6 g- Quantity: 1x DC motor 1x double helix Code M0132 Available Regular price €2.44 -€0.50 Price €1.94
Servo Driver for micro:bit, 16-Channel, 12-bit The micro:bit servo driver module, 16 channel, 12 bit, I2C interface. Have you ever had the problem of not having enough micro:bit PWM outputs when trying to create a robotic arm or other robot that requires multiple servos? At times like this a great solution comes to your aid. This servo controller will be the perfect choice. Code WV007 Available Price €18.14
Router TB6560 1 Axis 3A Stepper Motor Driver Board Router TB6560 1 Axis 3A Stepper Motor Driver Board features: - Minimum operating voltage: 10 V- Maximum operating voltage: 35 V (24V recommended)- Maximum current: ± 3 A- Stepper motor · two phases · four phases- Resolution of microsteps: full, 1/2, 1/8, and 1/16- PCB measurements: 75x50 mm- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply- 6N137 high speed optical coupling guarantees high speed without losing steps- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent- Protection circuit to ensure optimal performance- Maximum nominal output: 3 A, peak 3.5A Code I0106 Available Price €6.57
PCA9685 digital servo motor controller 16 channel PWM This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos. It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity. PCA9685 digital servo motor controller 16 channel PWM features: - Supply voltage: 3-5 VDC, - Maximum motor voltage: 6 VDC, - Number of channels: 16, - Resolution per channel: 12 bits, - Interface: I2C, - Working frequencies: 40-1000 Hz, - PCB size: 62.3x25.3mm . Code R0074 Available Price €4.21
Mini VNH3SP30 Stepper Motor Driver Module 30A Mini VNH3SP30 Stepper Motor Driver Modules capable of handling a high consumption motor. Code R0020 ✗ Out-of-Stock Price €4.01
LSC-16 Digital Servo Motor Controller 16 channels LSC-16 Digital Servo Motor Controller 16 channels features: - With current limiting protection. The servo output is isolated from the CPU to prevent increased servo current causing damage to the CPU. - CPU using high performance STM32 single chip microcomputer with ARM Cortex-M3 corer, control High precision 16-channel servo movement, adjustable speed. - 16M high capacity memory, enough for your use! It can contain 230 action groups! Each action group can hold up to 510 actions! - Supports online debugging, no need to install any driver by yourself (Install Drivers Automatically). - 0 ~ 3rd and 12th - 15th servo interface have over current protection! Greatly reducing the risk of burned servo due to locked rotor. Code R0046 Available Regular price €21.32 -€2.00 Price €19.32
Controller TB6612FNG DC PAP motor TB6612FNG controller, double H-bridge controller driver. Allows to control up to 2 current motors continuous or bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. An improved version of the L298N. H-bridges are made up of MOSFET transistors, rather than BJT transistors as in the L298N. The TB6612FNG has better efficiency and smaller dimensions than the L298N. Controller TB6612FNG DC PAP motor features: - Minimum operating voltage: 4.5 V - Maximum operating voltage: 13.5 V (15V max) - Maximum current: ± 3A per channel (1.2 A direct current per channel) - Logic voltage: 5V Code R0002 ✗ Out-of-Stock Price €4.95
L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.It incorporates a switch for the connection and disconnection of the entire module. L298N Motor Drive Controller Board Module Dual H Bridge DC with interruptor features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth /> Code M0183 Available Price €3.13
VNH3SP30 Stepper Motor Driver Module 30A Driver capable of handling up to two high consumption motors.We can weld 5mm screw terminals (not included), making it easy to connect other gauge cables. Code R0010 ✗ Out-of-Stock Regular price €12.88 -€2.50 Price €10.38
Mosfet 24V 5A IRF520 PWM controller Mosfet 24V 5A IRF520 PWM controller features: - The IRF520 controller module can control the PWM signal from the Arduino module and adjust the DC voltage of So that we can control the speed of the DC motor, the brightness of the bulb, the LEDs, the heater. - The built-in IRF520 N-MOSFET transistor - Operating voltage: 3.3V -5V ( compatible with ARDUINO Raspberry PI) - Charging voltage: 0-24V - Charging current: up to 5A (more than 1A, the system must be equipped with a heat sink point) - 60W max power (more than 10W must be equipped with a heat sink) - Terminalblock connectors - LED indicating the presence of power - Dimensions: 33x24mm Code A0022 Available Regular price €2.06 -€0.50 Price €1.56