TB6600 4.5A Single Axis CNC Controller

The controller creates step-by-step motor control functions preset with the latest imported high-speed chip and uses a combination of software and hardware methods to ensure superior anti-jam performance of the controller.
It also has reverse polarity protection, overvoltage protection, overcurrent protection, absolute guarantee of safe operation of the controller in a variety of hostile factory environments.
Applies to stepper motor control switches, round-trip motion control, fixed speed control. Industrial DKC-1A stepper motor controller features:
- Operating voltage: 5-32 VDC
- Signal entry point for the lower level entry
- Optimization of the acceleration of the S curve
- The maximum output frequency can reach 20 KHz

The DM556 low-voltage digital stepper motor controller, which uses the latest 32-bit DSP technology, is suitable for driving the 57 and 86 series motors Nema23, with excellent low-speed performance to meet the application needs of small and medium-sized equipment.

Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 features:
- 100% brand new and high quality
- Optical detector: TCST2103
- Length cable: 50cm
- Size: 32mm x 10mm

Feature of 3D Zum shield: - Input voltage 8-16 V
- 2 connectors for stepper motors
- 4 connectors for laser
- Analog connectors for LDR sensors
- Power jack connector
- Reset button
- Protection fuse for stepper motors
- Compatible with Arduino UNO
- Dimensions of PCB 67 x 54 mm
- Content:
       - 1x Zum Shield 3D
       - 1x UNO R3 Compatible Arduino
       - 1x Controller A4988
       - 1x Male pin strip
       - 1x Heatsink for A4988
       - 1x USB cable
       - Jumpers

Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.
Run easily with Arduino. Router TB6600 1 Axis 3.5A Stepper Motor Driver Board features:
- Minimum operating voltage: 9 V
- Maximum operating voltage: 40 V
- Maximum current: ± 3.5 A
- Maximum power: 160W
- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23
- Control inputs 5V optically isolated
- Step resolution: 200, 400, 400, 800, 1600, 3200, 6400
- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 y 1/32 adjustable by interruptor DIP
- Current control: 0.5A/>0A/>

Mechanical Ender 3 5 CR 10 20 X Pro 3D Printer features:
- Mechanical limit switch, Endstop
- 100% brand new and high quality
- 1A 125V AC switch - Compatible with Ender-3 series, CR-10 series, etc.
- PCB dimensions: 18mm x 18mm

RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825.

Router TB6560 1 Axis 3A Stepper Motor Driver Board features:
- Minimum operating voltage: 10 V
- Maximum operating voltage: 35 V (24V recommended)
- Maximum current: ± 3 A
- Stepper motor · two phases · four phases
- Resolution of microsteps: full, 1/2, 1/8, and 1/16
- PCB measurements: 75x50 mm
- CNC Router 1 Axis Controller Stepper motor controllers TB6560 3A driver board
- Operating voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply
- 6N137 high speed optical coupling guarantees high speed without losing steps
- Use of TB6560AHQ chip with low voltage shutdown, overheat stop and overcurrent
- Protection circuit to ensure optimal performance
- Maximum nominal output: 3 A, peak 3.5A

CNC shield for arduino works as a controller for CNC type milling machines,
3D printers, laser cutters .
CNC Shield Expansion Plate V3 Engraver 3D Printer features:

• 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible
• 4 support axes X, Y, Z, A
• 2 limit switches for each axis (6 in total)

Contented:
- 1x UNO R3 Atmega 328P 16U2 Compatible with Arduino
- 1x CNC Shield V3
- 4x A4988 Drivers
- 4x Heatsinks for A4988
- USB Cable
- Jumpers