10A DC-DC Converter Adjustable Downstream 8V-40V to 1.25V-36V This power supply delivers an output voltage lower than that of the input and allows power loads up to 10A. It has its heat sink, it is Recommended to use it for loads up to 8A for optimal cooling. Includes its foot protection kit, which greatly facilitates heat dissipation and use. 10A DC-DC Converter Adjustable Downstream 8V-40V to 1.25V-36V features: - Input voltage: DC 8V-40V - Output voltage: DC 1.25V-36V adjustable with potentiometer (can only be used as a reducing module, the input must be higher than 1.25V output) - Output current: 8A (Max 10A for a short time), adjustable with potentiometer. Below 5A it can cool naturally - Output power: Max 150W - Key components: - Electrolytic capacitors 470µF - 50V Code A0074 ✗ Out-of-Stock Price €11.15
Resistor 330K Ohm 5% 0,25W 1/4W Resistor 330K Ohm 5% 0,25W 1/4W features:-330 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0028 Available Price €0.07
Battery holder 4x AA 6V LR06 Battery holder 4x AA 6V LR06 features: - Cable 13cm long - Measurements 62x56x 16mm - Battery length max 50mm - Compatible batteries ( LR06, R06, MN1500, AM3, UM3, HP7) Code PP003 Available Price €1.23
MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V High power digital servo, better precision than the MG995. MG996R Metal Gears Digital Servo High Power Equivalent 12Kg 6V features: - Operating voltage: 4.8 V to 7.2 V- Consumption: 100mA- Torque max.: 12kg / cm (6V)- Operating speed: 0.22sec / 60degree (4.8V), 0.19sec/60degree (6V)- Max. Radio: 180ºC- Temperature range: 0-55 degrees- Weight: 55 g- Cable length: 29cm- Dimensions: 54 x38x 20 mm- Servo connector: JR (JR and Futaba adaptable) Code R0016 Available Regular price €7.40 -€1.00 Price €6.40
Resistor 220K Ohm 5% 0,25W 1/4W Resistor 220K Ohm 5% 0,25W 1/4W features:-220 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0027 Available Price €0.07
Gear Reducer Motor 6V DC 200RPM for Smart Car Gear Reducer Motor 6V DC 200RPM for Smart Car features: - Voltage: 3 to 6V DC- Speed without load: 200 RPM to 6V DC Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles - Wiring of the 6V DC 200 RPM motor with the L298N double bridge H controller module Code R0045 Available Price €1.98
12V Momentary LED Pushbutton Blue 22mm N/A NO Momentary LED Pushbutton Blue 22mm N/A NO features:- Type of operation: momentary (automatic return)- Contact switch: 1 NA (normally open)- Max Switch Classification: 2A / 12VDC-24VDC- Body material: Stainless steel- Button Material: Stainless steel- Protection Classification: IP67 / IK08- Operating temperature: -20C + 55C- Color: Blue Code K0310 Available Price €6.40
USB Cable for Arduino Type A-B USB Cable for Arduino Type A-B features: - Length: 50cm- Color: Blue Code K0158 Available Price €1.23
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.64
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of voltage and current.DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo features:- Input voltage: 4-38V- Output voltage: 1.25-36V- Current output: adjustable, 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 26mm x 14mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0014 Available Price €2.88
XL4015 DC-DC 5A Digital Step-down LED Converter with Voltmeter, Ammeter and USB Output This Step-down voltage converter includes 5 functions in one module. It can be used as a voltmeter, ammeter and measurements can be recovered through its USB port. The output voltage and voltage can be adjusted thanks to two potentiometers present in the module. It has an efficiency Very high, it has a display screen for voltage, current and two buttons to configure what you want to see. Characteristic: - Voltage of input: 5.5 - 36 V - Output voltage: 1.25-32 V continuously adjustable - Output current: 4.5 A (Max 5A for a short time) adjustable with potentiometer, - Power output: 75 W maximum (recommended to use 50 W, large pressure difference, please reduce power) - Operating temperature: -40 ° C - + 150 ° C Code A0077 ✗ Out-of-Stock Regular price €6.52 -€1.00 Price €5.52
DC Step Down Converter 3.3V 2A 3.4-6V DC Step Down Converter 3.3V 2A 3.4-6V features: - Voltage drop module- Input voltage: 3.4-6V- Output voltage: 3.3V- Current output: adjustable, max 2A- Operating temperature: -40 to + 85 ºC- Operating frequency: 1.5MHz- Efficiency conversion: up to 95%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 12 x 15 mm- Full charge output ripple: Vpp <50 mV- Output accuracy: ± 0.1V- Current IQ without load: 0.2mA- Stop current (EN) <10uA Code A0068 Available Price €2.79
3A DC Converter 4-53V Adjustable LM2596H Step Down Source Wide range of voltages, improved version. Drop module. They will use a multimeter to Check the output voltage and adjust the potentiometer. 3A DC Converter 4-53V Adjustable LM2596H Step Down Source features: - Based on the LM2596HVS-ADJ regulator - Rectification: Asynchronous - Output Voltage: 3v ~ 40v DC (adjustable) - Input Voltage: 4.5v - 53v DC - Max Output Current: 3A (with heat sink) - Ripple in output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2,5% - Operating temperature: -40ºC to + 85ºC - Measurements: 43x 21x 14 mm Code A0018 Available Price €2.31
8A DC Step-down Converter 8-40V to 1.25-35V Current Control XL4016 A high-performance regulator-booster. 24V battery charger - DC / CV method. Power supply of the laptop from a 12V car battery. A high-performance dimmer-regulator. Charger for Li-Ion, Li-Po batteries etc. - CC / CV method. LED Constant current driver for LED diodes. Characteristic: - Input voltage: 6V -40V - Output voltage: 1.25-35V (adjustable) - Output current: 8A, (10A maximum) - Output power: 300W maximum - Efficiency of Conversion: up to 95% - Wiring: Solderless terminal - Operating frequency: 300kHz - Ambient temperature exceeds 40 ° C, increase heat dissipation - LED indicator two-color; - Charge red - Fully charged light green - No charge green Code A0011 ✗ Out-of-Stock Price €6.57
Boost Buck Step Up-Down Automatic Converter Descripción:This is a powerful, efficient step-up (boost) and step-down (buck) switching voltage converter. It will automatically change between boosting and bucking to maintain a stable output voltage, regardless of the input.The output is set with a multi-turn potentiometer.Boost Buck Step Up-Down Automatic Converter features:- IC Chip: LM2577S-ADJ and LM2596S-ADJ - Module Properties: non-isolated Boost Buck constant current, constant voltage module (CC CV) charging module- Scope: High-power constant current LED driver.- Battery charger (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charger, solar panels, wind generators. Code A0017 Available Price €7.84
Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V features: - Voltage Drop Module - Use a multimeter to check the output voltage and adjust the potentiometer - Small size: 17mm x 11mm - Input voltage: 4.75-23V - Output voltage: 1.0-17V - Current output: 1.8A (peak max. 3A) - Operating temperature: -40 to + 85 ºC - Operating frequency: 240kHz - Conversion efficiency: up to 96% - Output ripple: 30mV (no-load) - Voltage regulation: ± 2.5% Code A0024 Available Price €2.06
Converter DC USB Step Down 7V-24V to 5V 3A Converter DC USB Step Down 7V-24V to 5V 3A features:- Voltage reduction module with USB connector- DIY mobile power supply, to achieve the 5v output to charge the phone, mp3, mp4, psp, etc. can not charge for the ipad- The USB output converter module has short circuit protection 5A current automatic protection- Based on the monolithic MP2307 controller- Rectification: not synchronous- Input voltage: DC 7v to 24v- Output voltage: DC 5v- Output current: 3A (Little time 4A)- Output connection: USB Type A female connector- Input connection: Terminal with screws- Efficiency of transformation: 96%- Switching frequency: 340KHz- Output ripple: 30mV (max.)- Load regulation: ± 0.5% Code A0016 Available Price €3.30
XL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 Descripción:Chip XL4015 - Upgrade of the LM2596Drop moduleUse a multimeter to check the output voltage and adjust the potentiometerVoltage controlXL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 features:- Input voltage: 4.5V-38V- Output voltage: 1.25-36.5V- Current output: 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0012 Available Price €4.09
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.64
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of voltage and current.DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo features:- Input voltage: 4-38V- Output voltage: 1.25-36V- Current output: adjustable, 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 26mm x 14mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0014 Available Price €2.88
XL4015 DC-DC 5A Digital Step-down LED Converter with Voltmeter, Ammeter and USB Output This Step-down voltage converter includes 5 functions in one module. It can be used as a voltmeter, ammeter and measurements can be recovered through its USB port. The output voltage and voltage can be adjusted thanks to two potentiometers present in the module. It has an efficiency Very high, it has a display screen for voltage, current and two buttons to configure what you want to see. Characteristic: - Voltage of input: 5.5 - 36 V - Output voltage: 1.25-32 V continuously adjustable - Output current: 4.5 A (Max 5A for a short time) adjustable with potentiometer, - Power output: 75 W maximum (recommended to use 50 W, large pressure difference, please reduce power) - Operating temperature: -40 ° C - + 150 ° C Code A0077 ✗ Out-of-Stock Regular price €6.52 -€1.00 Price €5.52
DC Step Down Converter 3.3V 2A 3.4-6V DC Step Down Converter 3.3V 2A 3.4-6V features: - Voltage drop module- Input voltage: 3.4-6V- Output voltage: 3.3V- Current output: adjustable, max 2A- Operating temperature: -40 to + 85 ºC- Operating frequency: 1.5MHz- Efficiency conversion: up to 95%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 12 x 15 mm- Full charge output ripple: Vpp <50 mV- Output accuracy: ± 0.1V- Current IQ without load: 0.2mA- Stop current (EN) <10uA Code A0068 Available Price €2.79
3A DC Converter 4-53V Adjustable LM2596H Step Down Source Wide range of voltages, improved version. Drop module. They will use a multimeter to Check the output voltage and adjust the potentiometer. 3A DC Converter 4-53V Adjustable LM2596H Step Down Source features: - Based on the LM2596HVS-ADJ regulator - Rectification: Asynchronous - Output Voltage: 3v ~ 40v DC (adjustable) - Input Voltage: 4.5v - 53v DC - Max Output Current: 3A (with heat sink) - Ripple in output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2,5% - Operating temperature: -40ºC to + 85ºC - Measurements: 43x 21x 14 mm Code A0018 Available Price €2.31
8A DC Step-down Converter 8-40V to 1.25-35V Current Control XL4016 A high-performance regulator-booster. 24V battery charger - DC / CV method. Power supply of the laptop from a 12V car battery. A high-performance dimmer-regulator. Charger for Li-Ion, Li-Po batteries etc. - CC / CV method. LED Constant current driver for LED diodes. Characteristic: - Input voltage: 6V -40V - Output voltage: 1.25-35V (adjustable) - Output current: 8A, (10A maximum) - Output power: 300W maximum - Efficiency of Conversion: up to 95% - Wiring: Solderless terminal - Operating frequency: 300kHz - Ambient temperature exceeds 40 ° C, increase heat dissipation - LED indicator two-color; - Charge red - Fully charged light green - No charge green Code A0011 ✗ Out-of-Stock Price €6.57
Boost Buck Step Up-Down Automatic Converter Descripción:This is a powerful, efficient step-up (boost) and step-down (buck) switching voltage converter. It will automatically change between boosting and bucking to maintain a stable output voltage, regardless of the input.The output is set with a multi-turn potentiometer.Boost Buck Step Up-Down Automatic Converter features:- IC Chip: LM2577S-ADJ and LM2596S-ADJ - Module Properties: non-isolated Boost Buck constant current, constant voltage module (CC CV) charging module- Scope: High-power constant current LED driver.- Battery charger (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charger, solar panels, wind generators. Code A0017 Available Price €7.84
Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V features: - Voltage Drop Module - Use a multimeter to check the output voltage and adjust the potentiometer - Small size: 17mm x 11mm - Input voltage: 4.75-23V - Output voltage: 1.0-17V - Current output: 1.8A (peak max. 3A) - Operating temperature: -40 to + 85 ºC - Operating frequency: 240kHz - Conversion efficiency: up to 96% - Output ripple: 30mV (no-load) - Voltage regulation: ± 2.5% Code A0024 Available Price €2.06
Converter DC USB Step Down 7V-24V to 5V 3A Converter DC USB Step Down 7V-24V to 5V 3A features:- Voltage reduction module with USB connector- DIY mobile power supply, to achieve the 5v output to charge the phone, mp3, mp4, psp, etc. can not charge for the ipad- The USB output converter module has short circuit protection 5A current automatic protection- Based on the monolithic MP2307 controller- Rectification: not synchronous- Input voltage: DC 7v to 24v- Output voltage: DC 5v- Output current: 3A (Little time 4A)- Output connection: USB Type A female connector- Input connection: Terminal with screws- Efficiency of transformation: 96%- Switching frequency: 340KHz- Output ripple: 30mV (max.)- Load regulation: ± 0.5% Code A0016 Available Price €3.30
XL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 Descripción:Chip XL4015 - Upgrade of the LM2596Drop moduleUse a multimeter to check the output voltage and adjust the potentiometerVoltage controlXL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 features:- Input voltage: 4.5V-38V- Output voltage: 1.25-36.5V- Current output: 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0012 Available Price €4.09