M12 Inductive Proximity Sensor NPN DC 6-36V LJ12A3-4-Z/BX 3D Printer M12 Inductive Proximity Sensor NPN DC 6-36V LJ12A3-4-Z/BX 3D Printer features: - This sensor can be configured as Z axis auto level - Inductive proximity sensor detection switch LJ12A3-4-Z / BX - NPN DC6-36V - Often used for 3D printer bed leveling - Typical application: 3D printer bed level sensor - Type of Cylindrical DC cable 3 type of cable (black, brown, blue) - Inductive sensor type - NPN NO (Normal Open) - Detecting Distance 4mm - DC supply voltage 6-36V - 300mA current output - 0.5KHz response frequency - Detects iron / aluminum - Operating temperature -25 ° C to + 55 ° C (Condition non-freezing) - Head diameter 12 mm - Size 6.2 x 2cm - Cable length 100cm Code S0125 Available Price €2.88
Arduino Multifunction shield - Display, LEDs, pushbuttons, buzzer Getting started with Arduino? This multi-function shield for Arduino UNO is ideal for your first Arduino DIY projects. It includes 4 7-segment displays, buzzer, 3 push buttons, 4 LEDs, potentiometer and sockets. Code M0230 Available Price €4.04
ESP8266 5V WiFi Relay Module AP Remote Control + STA You can easily control any device over the Internet through your phone, computer, etc. The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point). In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters). In STA mode, the relay module is connected to the access point (router) that supplies the network. Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers). You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off. Code W0067 Available Price €7.84
4-Channel 5V 10A Relay Module Characteristic: - Channels: 4 (independent protected by Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - Indicator LED: For each channel - Dimensions: 54x 72mm - 5V Optocoupled 4-Channel Relay Module - This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for the remote control + 4-channel 315 MHz IC2262 receiver: - Relay Module Programming 5V 10A 4 Channel with remote control + 4 channel receiver Code RL007 Available Price €3.30
Resistor 150R Ohm 5% 0,25W 1/4W Resistor 150R Ohm 5% 0,25W 1/4W features:-150R Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0006 Available Price €0.07
40x Male to male cables 10cm 40x Male to male cables 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont male connectors on both ends - Compatible with 2.54mm female connectors - High quality and good working condition - Easy to install and use Code K0107 Available Price €1.64
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo. Control of voltage and current.Use a multimeter to check the output voltage and adjust the potentiometer. Code A0132 Available Price €2.88
HX711 Module Weighing Pressure Sensor 24 Bits The module uses a 24-bit high precision A/D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. HX711 Module Weighing Pressure Sensor 24 Bits features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0118 Available Regular price €2.31 -€0.39 Price €1.92
Mosfet 24V 5A IRF520 PWM controller Mosfet 24V 5A IRF520 PWM controller features: - The IRF520 controller module can control the PWM signal from the Arduino module and adjust the DC voltage of So that we can control the speed of the DC motor, the brightness of the bulb, the LEDs, the heater. - The built-in IRF520 N-MOSFET transistor - Operating voltage: 3.3V -5V ( compatible with ARDUINO Raspberry PI) - Charging voltage: 0-24V - Charging current: up to 5A (more than 1A, the system must be equipped with a heat sink point) - 60W max power (more than 10W must be equipped with a heat sink) - Terminalblock connectors - LED indicating the presence of power - Dimensions: 33x24mm Code A0022 Available Regular price €2.06 -€0.50 Price €1.56
LSC-16 Digital Servo Motor Controller 16 channels LSC-16 Digital Servo Motor Controller 16 channels features: - With current limiting protection. The servo output is isolated from the CPU to prevent increased servo current causing damage to the CPU. - CPU using high performance STM32 single chip microcomputer with ARM Cortex-M3 corer, control High precision 16-channel servo movement, adjustable speed. - 16M high capacity memory, enough for your use! It can contain 230 action groups! Each action group can hold up to 510 actions! - Supports online debugging, no need to install any driver by yourself (Install Drivers Automatically). - 0 ~ 3rd and 12th - 15th servo interface have over current protection! Greatly reducing the risk of burned servo due to locked rotor. Code R0046 Available Regular price €21.32 -€2.00 Price €19.32
VNH3SP30 Stepper Motor Driver Module 30A Driver capable of handling up to two high consumption motors.We can weld 5mm screw terminals (not included), making it easy to connect other gauge cables. Code R0010 ✗ Out-of-Stock Regular price €12.88 -€2.50 Price €10.38
PCA9685 digital servo motor controller 16 channel PWM This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos. It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity. PCA9685 digital servo motor controller 16 channel PWM features: - Supply voltage: 3-5 VDC, - Maximum motor voltage: 6 VDC, - Number of channels: 16, - Resolution per channel: 12 bits, - Interface: I2C, - Working frequencies: 40-1000 Hz, - PCB size: 62.3x25.3mm . Code R0074 Available Price €4.21
SparkFun Ardumoto - Motor Driver Shield The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased. Code SP011 Available Price €19.83
Servo Driver for micro:bit, 16-Channel, 12-bit The micro:bit servo driver module, 16 channel, 12 bit, I2C interface. Have you ever had the problem of not having enough micro:bit PWM outputs when trying to create a robotic arm or other robot that requires multiple servos? At times like this a great solution comes to your aid. This servo controller will be the perfect choice. Code WV007 Available Price €18.14
A3967 DC Motor PAP Driver Stepper - Easy driver A3967 controller, double H-bridge controller driver. Allows to control up to 2 DC motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. A3967 DC Motor PAP Driver Stepper - Easy driver features: - Minimum operating voltage: 7.00 V - Voltage maximum operating: 30 V Code R0049 Available Price €2.44
DRV8833 Controller DC Motor PAP Driver DRV8833 can control up to two DC motors or one stepper motor with a constant current of 1.5 A (peak 4A ). The motors are controlled, independently by means of PWM signals the direction of rotation of the motors can be controlled, neutral or stop with a frequency of up to 100 kHz. Two input signals (IN1 and IN2) can be used to control one motor (connected to OUT1 and OUT2) and the other two input signals (IN3 and IN4) to control the second motor (connected to OUT3 and OUT4). NOTE: This DRV8833 dual-bridge motor controller is the replacement for the TB6612FNG dual-channel motor controller. The pins come unsoldered. If the motor draws currents above 0.6A, the use of a heat sink may be required. DRV8833 Controller DC Motor PAP features: Code R0082 ✗ Out-of-Stock Price €2.02
L298N Motor Drive Controller Board Module Dual H Bridge DC It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. L298N Motor Drive Controller Board Module Dual H Bridge DC features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles Code M0100 Available Price €2.31
L9110 Fan Motor Propeller Module 5V The module for DIY Arduino hobbyMotor driver L9110 for Arduino, Smart Car, RoboticsSmall magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features: - Operating voltage: 5V- PCB dimension: 3.5 x 2.6cm- Double red propeller- Blade length 75mm- Weight: 6 g- Quantity: 1x DC motor 1x double helix Code M0132 Available Regular price €2.44 -€0.50 Price €1.94
Mosfet 24V 5A IRF520 PWM controller Mosfet 24V 5A IRF520 PWM controller features: - The IRF520 controller module can control the PWM signal from the Arduino module and adjust the DC voltage of So that we can control the speed of the DC motor, the brightness of the bulb, the LEDs, the heater. - The built-in IRF520 N-MOSFET transistor - Operating voltage: 3.3V -5V ( compatible with ARDUINO Raspberry PI) - Charging voltage: 0-24V - Charging current: up to 5A (more than 1A, the system must be equipped with a heat sink point) - 60W max power (more than 10W must be equipped with a heat sink) - Terminalblock connectors - LED indicating the presence of power - Dimensions: 33x24mm Code A0022 Available Regular price €2.06 -€0.50 Price €1.56
LSC-16 Digital Servo Motor Controller 16 channels LSC-16 Digital Servo Motor Controller 16 channels features: - With current limiting protection. The servo output is isolated from the CPU to prevent increased servo current causing damage to the CPU. - CPU using high performance STM32 single chip microcomputer with ARM Cortex-M3 corer, control High precision 16-channel servo movement, adjustable speed. - 16M high capacity memory, enough for your use! It can contain 230 action groups! Each action group can hold up to 510 actions! - Supports online debugging, no need to install any driver by yourself (Install Drivers Automatically). - 0 ~ 3rd and 12th - 15th servo interface have over current protection! Greatly reducing the risk of burned servo due to locked rotor. Code R0046 Available Regular price €21.32 -€2.00 Price €19.32
VNH3SP30 Stepper Motor Driver Module 30A Driver capable of handling up to two high consumption motors.We can weld 5mm screw terminals (not included), making it easy to connect other gauge cables. Code R0010 ✗ Out-of-Stock Regular price €12.88 -€2.50 Price €10.38
PCA9685 digital servo motor controller 16 channel PWM This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos. It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity. PCA9685 digital servo motor controller 16 channel PWM features: - Supply voltage: 3-5 VDC, - Maximum motor voltage: 6 VDC, - Number of channels: 16, - Resolution per channel: 12 bits, - Interface: I2C, - Working frequencies: 40-1000 Hz, - PCB size: 62.3x25.3mm . Code R0074 Available Price €4.21
SparkFun Ardumoto - Motor Driver Shield The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased. Code SP011 Available Price €19.83
Servo Driver for micro:bit, 16-Channel, 12-bit The micro:bit servo driver module, 16 channel, 12 bit, I2C interface. Have you ever had the problem of not having enough micro:bit PWM outputs when trying to create a robotic arm or other robot that requires multiple servos? At times like this a great solution comes to your aid. This servo controller will be the perfect choice. Code WV007 Available Price €18.14
A3967 DC Motor PAP Driver Stepper - Easy driver A3967 controller, double H-bridge controller driver. Allows to control up to 2 DC motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32. A3967 DC Motor PAP Driver Stepper - Easy driver features: - Minimum operating voltage: 7.00 V - Voltage maximum operating: 30 V Code R0049 Available Price €2.44
DRV8833 Controller DC Motor PAP Driver DRV8833 can control up to two DC motors or one stepper motor with a constant current of 1.5 A (peak 4A ). The motors are controlled, independently by means of PWM signals the direction of rotation of the motors can be controlled, neutral or stop with a frequency of up to 100 kHz. Two input signals (IN1 and IN2) can be used to control one motor (connected to OUT1 and OUT2) and the other two input signals (IN3 and IN4) to control the second motor (connected to OUT3 and OUT4). NOTE: This DRV8833 dual-bridge motor controller is the replacement for the TB6612FNG dual-channel motor controller. The pins come unsoldered. If the motor draws currents above 0.6A, the use of a heat sink may be required. DRV8833 Controller DC Motor PAP features: Code R0082 ✗ Out-of-Stock Price €2.02
L298N Motor Drive Controller Board Module Dual H Bridge DC It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. L298N Motor Drive Controller Board Module Dual H Bridge DC features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles Code M0100 Available Price €2.31
L9110 Fan Motor Propeller Module 5V The module for DIY Arduino hobbyMotor driver L9110 for Arduino, Smart Car, RoboticsSmall magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features: - Operating voltage: 5V- PCB dimension: 3.5 x 2.6cm- Double red propeller- Blade length 75mm- Weight: 6 g- Quantity: 1x DC motor 1x double helix Code M0132 Available Regular price €2.44 -€0.50 Price €1.94