Analogical Acoustic Sensor 4-Pin Microphone Sound Detector Module Sound detection module for Arduino projects, smart cars. Analogical Acoustic Sensor 4-Pin Microphone Sound Detector Module features: - Adjustable High Sensitivity Acoustic Sensor - LM393 comparator chip - Integrated indicator LED - AO analog output, output voltage signal in time real microphone - DO digital output, sensitivity adjustable through potentiometer - Frequency Range between 30 and 15000 Hz - Power 4 ~ 6V - Measurements 36x16x15mm Code S0017 Available Price €1.79
Mini VNH3SP30 Stepper Motor Driver Module 30A Mini VNH3SP30 Stepper Motor Driver Modules capable of handling a high consumption motor. Code R0020 ✗ Out-of-Stock Price €4.85
Prototype Protoboard Breadboard 170 points for Arduino Prototype Protoboard Breadboard 170 points Arduino features:- 170 connections- Base with adhesive to attach it to the work surface- Measurements: 45x35x9mm- Various colors Code PB001 Available Price €1.15
HCF4017BE DIP16 Counters/Dividers ST Microelectronics Integrated Circuit HCF4017BE DIP16 Counters/Dividers ST Microelectronics Integrated Circuit features: - Blister: DIP16- Number of pins: 16- Step between pins: 2.54 mm- Manufacturer: ST Microelectronics - VDD power supply voltage: 3 - 15 VDC- Input voltage: VDD- High output voltage level V (OH): 4.95 - 14.95 VDC- Output voltage low level V (OL): 0.05 VDC- High input voltage level V (IH): 3.5 - 11 VDC- Input voltage low level V (IL): 1.5 - 4 VDC - Inactive state current: 0.04 - 600 μA- Output drive current I (OH): -2.4 - 0.36 mA- Output leakage current I (OL): 0.36 - 2.4 mA- Input leakage current I (IH), I (IL): ± 1 μA - Operating temperature: -40 ° C to 85 ° C- Storage temperature: -65 ° C to 150 ° C Code T0062 Available Price €1.10
16-bit I2C ADS1115 module, 4-channel ADC with professional gain amplifier PGA The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden. Code M0226 Available Price €5.95
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €11.99
Power supply 5V 3A 15W USB-C Mobile Charger 5V 3A 3100mA with connector USB-C. This power supply has an additional USB-A connector. Code RA066 ✗ Out-of-Stock Price €10.90
Controller Super SNES USB 1.5m Super SNES Classic Controller Super SNES USB Controller is compatible with operating system: Windows 98 / ME / Vista / 2000/2003 / XP / 7/7/8 / 8.1 / 10; Mac OS X and beyond, arcade emulator, nintendo emulator, Raspberry pi and pi Model 2B, Retro Pi OS The SNES controller works with any emulator you want to download and use (Google SNES emulator, then the same for ROMs e.g. Joystick Mapper / OpenEMU for Mac OS; Virtuans for Windows OS, etc.). Code RA049 Available Price €3.99
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €7.90
USB Host Shield Google Android ADK UNO Mega 2560 USB Host Shield Google Android ADK UNO Mega 2560 features: Shield ADK USB allows: - Communication with other USB devices, to build their own mobile accessories- Create projects that require USB Host functionality- Supports USB 2.0, Android ADK- It can also be used with any device equipped with SPI interface- Compatible with Android devices: v2.3.4 and above- USB Host with support for HUB protocol Code M0005 Last items in stock Price €19.50
Dipole Pentaband waterpoof Antenna A waterproof pentaband antenna X000016 for all your wireless projects with Arduino and development boards Code X0016R Available Price €5.95
3D Zum Scan Shield + UNO R3 CH340 + A4988 Stepper Feature of 3D Zum shield: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- Content: - 1x Zum Shield 3D - 1x UNO R3 Compatible Arduino - 1x Controller A4988 - 1x Male pin strip - 1x Heatsink for A4988 - 1x USB cable - Jumpers Code I0057 ✗ Out-of-Stock Price €20.90
Sensor Cable - Electrode Pads (3 connector) This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads. Code SP075 Available Price €8.99
LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 features:- Shield LCD TFT 2.4 "Touch 3V expansion board for Uno R3- Facilitates connections between the TFT LCD 2.4 "Touch 3V with SD card reader and the Arduino UNO board- Put the screen on the shield and you can connect it directly to the Arduino UNO- UNO R3 2.4 "TFT LCD shield TFT LCD PCB Adapter for Arduino UNO STM32- The TFT01 LCD screen operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top- The TFT LCD PCB adapter for UNO is compatible with the Arduino pins, the user can plug directly the TFT LCD PCB adapter into the shield and placed on the Arduino board. - Can be used with a UNO and LCD screen Code P0004 Available Price €6.90
Qwiic cable 50mm It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 50mm long Code SP040 Available Price €1.19
Arduino NICLA Sense ME Nicla Sense ME is the smallest Arduino-developed board equipped with a range of the latest Bosch environmental and motion sensors. The module is based on the nRF52832 ARM Cortex M4 chip clocked at 64 MHz with 512 kB of Flash, 64 kB of RAM and 2 MB of SPI Flash and 2 MB of QSPI embedded memory. The Nicla Sense ME features the Bosch BHI260AP, BMP390, BMM150 and BME688 embedded sensors. Code ABX00050 Last items in stock Price €95.59
Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM This module, which uses the exclusive L298P chip for driving high-power motors, can directly control two DC motors, with a drive current up to 2A. The motor output uses eight-speed Schottky diodes as protection.The design of the letter allows you to connect directly to the Arduino UNO R3 for easier use. Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM features: - 1 logical step of the input voltage VD: 5 VDC- Control of the input voltage VS and control by pulse width modulation: - VIN input: 6 - 12 VDC - PWRIN input: 4.8 - 35 VDC- Logic current flow: Iss <36m A- Operation current management: Io <2 A- Maximum power dissipation 25W (T = 75 ° C)- Input of the control signal: Code M0136 Available Regular price €11.50 -€1.51 Price €9.99
Joystick Shield compatible with Arduino UNO Mega Shield allows you to be directly punched to an Arduino Uno, Mega board and convert your Arduino board into a controller like the game console system. Joystick Shield compatible with Arduino UNO Mega features: - 3.3V / 5V voltage- 4 large buttons ABCD- 2 small EF buttons- 1 button on the joystick)- 2-axis joystick (x, y)- Nokia 5110 LCD screen interface- Interface nRF24L01 +- Dimensions of PCB: 87 x54 mm Code M0021 Available Price €4.95
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €7.90
USB Host Shield Google Android ADK UNO Mega 2560 USB Host Shield Google Android ADK UNO Mega 2560 features: Shield ADK USB allows: - Communication with other USB devices, to build their own mobile accessories- Create projects that require USB Host functionality- Supports USB 2.0, Android ADK- It can also be used with any device equipped with SPI interface- Compatible with Android devices: v2.3.4 and above- USB Host with support for HUB protocol Code M0005 Last items in stock Price €19.50
Dipole Pentaband waterpoof Antenna A waterproof pentaband antenna X000016 for all your wireless projects with Arduino and development boards Code X0016R Available Price €5.95
3D Zum Scan Shield + UNO R3 CH340 + A4988 Stepper Feature of 3D Zum shield: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- Content: - 1x Zum Shield 3D - 1x UNO R3 Compatible Arduino - 1x Controller A4988 - 1x Male pin strip - 1x Heatsink for A4988 - 1x USB cable - Jumpers Code I0057 ✗ Out-of-Stock Price €20.90
Sensor Cable - Electrode Pads (3 connector) This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads. Code SP075 Available Price €8.99
LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 features:- Shield LCD TFT 2.4 "Touch 3V expansion board for Uno R3- Facilitates connections between the TFT LCD 2.4 "Touch 3V with SD card reader and the Arduino UNO board- Put the screen on the shield and you can connect it directly to the Arduino UNO- UNO R3 2.4 "TFT LCD shield TFT LCD PCB Adapter for Arduino UNO STM32- The TFT01 LCD screen operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top- The TFT LCD PCB adapter for UNO is compatible with the Arduino pins, the user can plug directly the TFT LCD PCB adapter into the shield and placed on the Arduino board. - Can be used with a UNO and LCD screen Code P0004 Available Price €6.90
Qwiic cable 50mm It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 50mm long Code SP040 Available Price €1.19
Arduino NICLA Sense ME Nicla Sense ME is the smallest Arduino-developed board equipped with a range of the latest Bosch environmental and motion sensors. The module is based on the nRF52832 ARM Cortex M4 chip clocked at 64 MHz with 512 kB of Flash, 64 kB of RAM and 2 MB of SPI Flash and 2 MB of QSPI embedded memory. The Nicla Sense ME features the Bosch BHI260AP, BMP390, BMM150 and BME688 embedded sensors. Code ABX00050 Last items in stock Price €95.59
Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM This module, which uses the exclusive L298P chip for driving high-power motors, can directly control two DC motors, with a drive current up to 2A. The motor output uses eight-speed Schottky diodes as protection.The design of the letter allows you to connect directly to the Arduino UNO R3 for easier use. Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM features: - 1 logical step of the input voltage VD: 5 VDC- Control of the input voltage VS and control by pulse width modulation: - VIN input: 6 - 12 VDC - PWRIN input: 4.8 - 35 VDC- Logic current flow: Iss <36m A- Operation current management: Io <2 A- Maximum power dissipation 25W (T = 75 ° C)- Input of the control signal: Code M0136 Available Regular price €11.50 -€1.51 Price €9.99
Joystick Shield compatible with Arduino UNO Mega Shield allows you to be directly punched to an Arduino Uno, Mega board and convert your Arduino board into a controller like the game console system. Joystick Shield compatible with Arduino UNO Mega features: - 3.3V / 5V voltage- 4 large buttons ABCD- 2 small EF buttons- 1 button on the joystick)- 2-axis joystick (x, y)- Nokia 5110 LCD screen interface- Interface nRF24L01 +- Dimensions of PCB: 87 x54 mm Code M0021 Available Price €4.95