Controller Super SNES USB 1.5m

USB A to Mini USB B cable 50cm features:
- Color: Blue or black
- Length: 50cm

Desoldering iron for the removal of excess tin. You can quickly and effectively remove solder from a plate or circuit.
Replaceable antistatic nozzle.
Manufactured in Aluminum.
Aluminum Desoldering Pump Tin Antistatic Suction features:
- Length: 190mm
- Desoldering pump
- High suction power
- Replaceable long-life silicone tip
- Light weight
- Easy use with one hand, light and resistant
- Vacuum Solder Aluminum Desoldering Pump Solder Remover Pump Tool
- A good quality product for fast and efficient removal of excess solder, ideal for PCB repair
- High-capacity spring-loaded plunger quickly eliminates welding in one action. The Pumping tool easily
- Disassemble for a quick clean

Driver DRV8833 can control up to two DC motors or one stepper motor with a constant current of 1.5 A (peak 4A ). The motors are controlled, independently by means of PWM signals the direction of rotation of the motors can be controlled, neutral or stop with a frequency of up to 100 kHz. Two input signals (IN1 and IN2) can be used to control one motor (connected to OUT1 and OUT2) and the other two input signals (IN3 and IN4) to control the second motor (connected to OUT3 and OUT4). NOTE: This DRV8833 dual-bridge motor controller is the replacement for the TB6612FNG dual-channel motor controller. The pins come unsoldered. If the motor draws currents above 0.6A, the use of a heat sink may be required. DRV8833 Controller DC Motor PAP features:

Thermally Conductive Silicone Paste H facilitates the transfer of calories between the electronic components and the radiator.
It is necessary for the correct operation of any type of temperature sensors.

This set will make your project look like take out of 80s! Box and two controllers imitate a game console only for 25 EUR. Do you miss old times of Nintendo? You won´t anymore with this great set. It is perfect for a gift as well. Check out product characteristics for further information

Mini ESP8266 ESP12E CH340 WiFi Development
NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features:

- Compatible with Arduino, programming with the Arduino IDE
- Power supply voltage: 5V
- LOGICAL LEVELS: 3.3V
- 11 input / output pins
- 1 ADC (input: 0-3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz - Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and power management units Integrated

1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:
- Channel: 1 (protected with Optocoupler)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator
- Dimensions: 30x 54mm
- Has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

Ethernet Patchcord UTP 5e 1m features:
- For Raspberry Pi 2 and Pi 3, B and B +
- HDMI V1.3b cable and full 1080P (category 2) resolution
- Type A male at both ends
- High quality gold shielded connectors
- Manufactured with high quality copper conductors (OFC-Oxygen Free Copper- 99.99%) that guarantees the highest transmission quality
- Refresh rates up to 120Hz
- Length: 50cm
- Quantity: 1 unit