Joystick Breakout Board for BBC Micro:Bit The joystick board can be used to simulate the mouse keyboard. The 3V, G, P0 and P1 are connected to a card micro: bit to imitate the serial port. This board consists of 6 buttons and joystick. Connect the joystick and buttons to the micro: bit pins. Code RA040 Available Price €9.95
TRRS jack adapter 3.5mm female audio with PCB board 3.5mm Audio Jack Breakout Headphone Video Audio MP3 Jack Module. This female jack connector adapter 3.5mm audio soldered on a PCB board, it is ideal to use in our projects. TRRS connectors are the audio-style connectors seen on some phones, MP3 players and development boards. TRRS stands for "Tip, Ring, Ring, Sleeve", reflecting the fact that unlike a standard stereo connector, this one actually has three conductors and a ground. Code M0195 Available Price €0.95
Resistor 330 Ohm 5% 0,25W 1/4W Resistor 330 Ohm 5% 0,25W 1/4W features:-330 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0009 Available Price €0.08
NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA - This module includes PA preamplifier and LNA (Low-noise amplifier)- Comes with the SMA antenna for 2.4GHz (2dB)- Outdoor - transmission up to 250kbps and a distance of up to 1 kilometer- Works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripherals control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA features: * Based on chip NRF24L01 +* Free band: 2.4GHz ISM* Speed: 250kbps, 1Mbps, 2Mbps* Work current- Reception: 45 mA- Transmission: 115 mA (4.2uA -sleep mode)* Receiving sensitivity:-104dB 250kbps- 95dB 1Mbps- 92dB 2Mbps* SPI interface Code W0063 Last items in stock Price €6.95
Rechargeable Battery Samsung INR18650 2500mAh Li-ion Rechargeable Battery Samsung INR18650 2500mAh Li-ion 3.7V 20A unprotected features: IMPORTANT: This battery does not have a protection circuit. Use it at your own risk. Do not charge over 4.2V Do not discharge below 3V Do not change polarity Do not heat the battery, or expose it to high temperatures Do not wet or expose to environments of High humidity For long periods of storage it should be stored below 45 ° C After long periods of storage you will probably need to do some charging cycles to increase the capacity again. Quantity: 1 unit Nominal capacity: 2500mAh (0.2C, 2.75V discharge) Minimum capacity: 2450mAh (0.2C, 2.75V discharge) Charging voltage: 4.2 ± 0.05 V Code PP030 ✗ Out-of-Stock Price €6.59
Prototype Breadboard Protoboard 840 points for Arduino Prototype Breadboard Protoboard 840 points Arduino features: - 840 Connections - Linkable with other Boards - Base with adhesive to attach it to the work surface - Measures 165x55x8mm Code PB008 Available Price €3.29
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development Mini ESP8266 ESP12E CH340 WiFi Development NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC It works as a standard WiFi 802.11 b / g / n 2.4 GHz Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features: - Compatible with Arduino, programming with the Arduino IDE - Power supply voltage: 5V - LOGICAL LEVELS: 3.3V - 11 input / output pins - 1 ADC (input: 0-3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and power management units Integrated Code W0061 Available Price €3.49
Sensor Module Infrared Obstacle Detector Car Robot Ideal for projects with ARDUINO, Smart Car. Sensor Module Infrared Obstacle Detector Car Robot features: - Power supply: 3.3 - 5V DC - OUT level 0/1 output - Sensitivity adjustment - Power LED - Distance from detection: 2 - 30cm (max60cm) - detection angle: 35º - LED output status indicator - Dimensions: 40x13x8mm Code S0011 Available Price €1.49
L293D Motor Drive Shield Expansion Board It allows controlling many different types of engines: - Up to 4 bidirectional current motors- Up to 2 stepper motors (unipolar or bipolar) In addition it is provided with two connectors for servos. L293D Motor Drive Shield Expansion Board features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A (650mA)- Logic voltage: 5V- Controller L293D- Measures: 70x55x20 mm L293D controller consists of 4 H bridges with 650 mA current with thermal protection.Pull-down resistors keep the motors off during startup. Code R0001 Available Price €2.95
MyoWare Cable Shield This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person. Code SP072 Backorder Price €6.49
Extension Board Shield Nano V3.0 ATmega328P Extension Board Shield for Arduino Nano V3.0. Code B0025 Available Price €2.95
Shield for Arduino Mega2560 Prototype PCB shield board with screw terminal block for Arduino. A very convenient solution for first experiments with Arduino Mega board. To assemble your projects in a comfortable and tidy way, access to all Arduino Mega2560 pins, universal board area, 5V and Gnd buses, reset button. Shield is supplied assembled. Code B0151 Available Regular price €11.95 -€1.00 Price €10.95
MyoWare Power Shield MyoWare Power Shield is designed to use two standard CR2032 coin cell batteries to power the MyoWare muscle sensor. These will be connected in parallel for extended capacity at a nominal 3.0V. Code SP071 Backorder Price €6.49
Arduino NICLA Voice Nicla Voice combines a powerful Syntiant® NDP120 Neural Decision Processor™ (NDP), a high-performance IM69D130 microphone, a BMI270 6-axis intelligent motion sensor, a BMM150 3-axis magnetometer and Bluetooth® Low Energy connectivity. Code ABX00061 Last items in stock Price €95.59
SparkFun WiFi Shield - ESP8266 The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on. Code SP006 Last items in stock Price €21.99
ATmega328P Nano V3.0 Adapter Terminal Block Connector ATmega328P Nano V3.0 Adapter Terminal Block Connector features: - Nano V3.0 Atmega328P adapter with loose connectors and solder pins - PCB dimensions: 53mm x 35mm Code B0027 Available Price €2.09
Arduino Edge Control A remote monitoring and control solution, optimised for outdoor environments. Collect real-time data from smart sensors and leverage everything to the edge, in your smart farm management. Code AKX034 Backorder Price €216.59
Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM This module, which uses the exclusive L298P chip for driving high-power motors, can directly control two DC motors, with a drive current up to 2A. The motor output uses eight-speed Schottky diodes as protection.The design of the letter allows you to connect directly to the Arduino UNO R3 for easier use. Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM features: - 1 logical step of the input voltage VD: 5 VDC- Control of the input voltage VS and control by pulse width modulation: - VIN input: 6 - 12 VDC - PWRIN input: 4.8 - 35 VDC- Logic current flow: Iss <36m A- Operation current management: Io <2 A- Maximum power dissipation 25W (T = 75 ° C)- Input of the control signal: Code M0136 Available Regular price €11.50 -€1.51 Price €9.99
ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino UNO V5.0 ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino UNO V5.0 features: - To mount your projects in a comfortable and orderly way, access to all the pins of Arduino Uno R3, it has a universal plate and protoboard zone, 5V and Gnd buses, reset pushbutton, pushbutton and 2 general purpose leds, zones for integrated Soic and Dip- The seamless mini breadboard has 170 connection points.- You can stick on the shield with its self-adhesive back. Code M0016 Available Regular price €2.20 -€0.21 Price €1.99
3D Zum Scan Shield + UNO R3 CH340 + A4988 Stepper Feature of 3D Zum shield: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- Content: - 1x Zum Shield 3D - 1x UNO R3 Compatible Arduino - 1x Controller A4988 - 1x Male pin strip - 1x Heatsink for A4988 - 1x USB cable - Jumpers Code I0057 ✗ Out-of-Stock Price €20.90
Arduino Pro PORTENTA H7 The Arduino Portenta H7 represents a new family of chips designed for IoT applications. The board uses the STM32H747 microcontroller equipped with Cortex-M7 and Cortex-M4 cores, which allows it to run programs written in Arduino®, MicroPython or JavaScript. In addition, the Arduino Portent H7 is characterised by high performance and at the same time energy efficiency. Code ABX42 Available Price €125.99
MyoWare 2.0 Cable Shield This Cable Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare 2.0 muscle sensor without actually connecting it to your person. Code SP045 Available Price €7.49
L293D Motor Drive Shield Expansion Board It allows controlling many different types of engines: - Up to 4 bidirectional current motors- Up to 2 stepper motors (unipolar or bipolar) In addition it is provided with two connectors for servos. L293D Motor Drive Shield Expansion Board features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A (650mA)- Logic voltage: 5V- Controller L293D- Measures: 70x55x20 mm L293D controller consists of 4 H bridges with 650 mA current with thermal protection.Pull-down resistors keep the motors off during startup. Code R0001 Available Price €2.95
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €7.90
Arduino Edge Control A remote monitoring and control solution, optimised for outdoor environments. Collect real-time data from smart sensors and leverage everything to the edge, in your smart farm management. Code AKX034 Backorder Price €216.59
Sensor Shield V5 APC220 Arduino compatible Arduino Sensor Shield V5 APC220 features: Sensor Shield V5.0 allows: - Being punctured directly to an Arduino Uno, Mega, Leonardo plate- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more Code M0001 Available Price €2.89
MyoWare Power Shield MyoWare Power Shield is designed to use two standard CR2032 coin cell batteries to power the MyoWare muscle sensor. These will be connected in parallel for extended capacity at a nominal 3.0V. Code SP071 Backorder Price €6.49
CNC Shield Expansion Plate V3 Engraver 3D Printer CNC shield for arduino works as a controller for CNC type milling machines, 3D printers, laser cutters . CNC Shield Expansion Plate V3 Engraver 3D Printer features: 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible 4 support axes X, Y, Z, A 2 limit switches for each axis (6 in total) Code I0011 Available Price €2.75