1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino

Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:
- Model: GL5539
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 100mW
- Resistance with light (10lux): 50-100KΩ
- Resistance with darkness (0lux): 5MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC

Raspberry Pi HD Pi NoIR V2 camera board Raspberry Pi HD Pi NoIR camera board connects to any Raspberry Pi or Compute Module to create HD photos and video. The Pi NoIR (without infrared) is the same as the standard camera module but without an infrared filter. Therefore, it is excellent for photography and video in the dark.
The module uses Sony's IMX219PQ image sensor that offers high-speed, high-sensitivity video images.
The Pi NoIR module offers contamination from Reduced image such as fixed pattern noise and smudges. It also has automatic control functions such as exposure control, white balance and luminance detection. Raspberry Pi NoIR Camera Board, Sony IMX219 8 Megapixel Sensor features:
and benefits: No infrared filter
High quality images

High-quality membrane keyboard, with 16-key matrix, ultra-thin, less than 1mm thick, with adhesive system on the reverse side.
Ideal for your Arduino projects, but can also be used with other microcontrollers.
Matrix Membrane Keyboard 4x4 Modulo features:

- Rating circuit, Max: DC 35V 100 mA
- Cable length: 85 mm
- Dupont 8 pin connector
- Specific insulation: 100 M Ohm, 100V
- Useful life: + 1 million uses
- Contact parting:

This module is an active buzzer for Arduino and emits different sounds at various frequencies.
It does not accept oscillation source, it only receives square waves for drive sound. 

Phillips blue Phillips screwdriver made of steel and plastic suitable for screws with 2.0mm head for electronic applications. Phillips screwdriver 45x2.0mm cross head features:
- Head type: Star
- Specification of the screwdriver: 45x2.0mm
- Material: Steel and plastic
- Screw driver size: 4.5x0.6x0.6cm / 1.77x0.24x0.24 "

Ideal for building a car with obstacle detector, light follower.
Includes battery compartment for 4 AA batteries and ignition switch. (batteries not included). 4WD Robot Smart Car Chassis 4x Wheels DIY features:
- Voltage: 3 to 6Vdc
- Speed without load: 100 RPM to 6Vdc
- No-load current: 90mA to 3Vdc - 180mA to 6Vdc
- Dimensions of the wheel: diameter 65mm - width 26 mm

The optical module (reflective) sensor with CMOS Schmitt inverter 74HC14D, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of an object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver.
The sensor allows the detection of an object at a distance of up to 15 mm. TCRT5000 IR Infrared Sensor Module features:
- The module has an output: digital
- CMOS Schmitt inverter 74HC14D
- Power supply: 5V - Range: 0.2 mm - 15 mm

15x Electrolytic Capacitor 1uF 50V 105º C PIC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 1uF
-Maximum tension: 50V
-Maximum temperature: 105º C
-Dimensions: 5x11mm
-Quantity: 15 units