Mclon Car Chassis 2x DIY Wheels

Led module infrared sensor for Arduino
Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nm
Particularly sensitive to the flame spectrum.
This optical flame sensor is a device that detects the existence of combustion by the light emitted by it.
Infrared LED Flame Sensor 5mm module features:
- 4 Pins Output:
    - A0: analog output
    - D0: digital output
    - GND: ground connection
    - VCC: 5V module power
- Range of light, Distance of 80 cm.
- Angle detection of about 60 degrees,
- This light can be detected by an optical sensor,
- Can be captured by digital inputs and analog inputs of Arduino.

Metal casing with Internal magnet Characteristic: - Power 2-3W
- Impedance: 4 Ohm - Shape: Round - Thickness: 5.3mm / 0.21 " - Diameter: 40mm / 1.6" - Quantity: 1 unit

10x Linear Potentiometers 10k OHM kΩ features:
- Horizontal variable resistance PCB
- 10k Ohm kΩ Linear
- Quantity: 10 units

It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
L298N Motor Drive Controller Board Module Dual H Bridge DC features:
- Minimum operating voltage: 5 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A
- Logic voltage: 5V
- PWM signal inputs for speed control
- Outputs: for 2 DC motors or for a bipolar stepper motor
- Measures: 43x43x24 mm
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles

Rechargeable Battery Samsung INR18650 2500mAh Li-ion 3.7V 20A unprotected features:
IMPORTANT: This battery does not have a protection circuit.
Use it at your own risk.
Do not charge over 4.2V
Do not discharge below 3V
Do not change polarity
Do not heat the battery, or expose it to high temperatures
Do not wet or expose to environments of High humidity
For long periods of storage it should be stored below 45 ° C
After long periods of storage you will probably need to do some charging cycles to increase the capacity again.
Quantity: 1 unit
Nominal capacity: 2500mAh (0.2C, 2.75V discharge)
Minimum capacity: 2450mAh (0.2C, 2.75V discharge)
Charging voltage: 4.2 ± 0.05 V

Quartz Crystal Oscillator 16 MHz features:
- Low Profile Crystal Oscillator
- Type: Quartz Crystal 16 MHz
- Frequency: 16 MHz
- Format: Low profile
- Assembly: Intern

The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel
We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit. The module is supplied in a soldered version.

M12 Inductive Proximity Sensor NPN DC 6-36V LJ12A3-4-Z/BX 3D Printer features:
- This sensor can be configured as Z axis auto level
- Inductive proximity sensor detection switch LJ12A3-4-Z / BX
- NPN DC6-36V
- Often used for 3D printer bed leveling
- Typical application: 3D printer bed level sensor
- Type of Cylindrical DC cable 3 type of cable (black, brown, blue)
- Inductive sensor type
- NPN NO (Normal Open)
- Detecting Distance 4mm
- DC supply voltage 6-36V
- 300mA current output
- 0.5KHz response frequency
- Detects iron / aluminum
- Operating temperature -25 ° C to + 55 ° C (Condition non-freezing)
- Head diameter 12 mm
- Size 6.2 x 2cm
- Cable length 100cm