Infrared LED Flame Sensor 5mm module

Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 10m. DS18B20 Digital Temperature Sensor Probe 10m features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 °C to 125 °C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
      - Vcc red
      - Yellow digital output
- Inocidable steel
- Cable length: 10m

The BME280 is an environmental sensor (SEN0236) integrating a temperature sensor, a humidity sensor and a barometer. Powered from 3.3 V to 5 V with I2C and SPI interface. Measuring range: temperature: -40 °C to 85 °C, humidity: 0 %RH to 100 %RH, pressure: 300 hPa to 1100 hPa.

Also available with waterproof casing and 100cm cable and 200cm. DS18B20 Temperature Sensor TO-92 0.5ºC Precision 5V Integrated features:
- Device function: Temperature sensor
- Type of output: Digital
- Supply voltage: 3V to 5.5V
- Accuracy: ± 0.5ºC
- Temperature threshold: Programmable
- Operating temperature: -55ºC to + 125ºC
- Encapsulated: TO-92
- Supply current: 1.5mA

The GY-906 BCC is a plate-mounted temperature sensor, based on an integrated 3 V infrared thermometer, single zone, medical precision, compensated gradient, accuracy within 5 cm is approximately 0.5 degrees higher

The DS18B20 is a digital temperature sensor from Dallas Semi Conductors, used to measure ambient temperature or to carry out tests. It supports multipoint readings of the mesh networking type, being able to be deployed in three lines, in order to achieve these readings, it has a built-in pull-up resistance. Dallas Temperature Sensor Module DS18B20 features:
- Operating voltage: 3 - 5.5 VDC
- Measurement operating temperature: -55 ° C - 125 ° C
- Output current: 5 μA
- Accuracy of ± 0.5 ° C between -10 ° C and + 85 ° C
- Storage temperature: -55 ° C - + 125 ° C
- 100% new and high quality
- Module DS18B20 temperature measurement sensor
- The DS18B20 sensor has a pull-up resistor
- Power indicator LED on the module

NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance.   Thermistor NTC 10.0K 5% MF52A epoxy resin coating resistor features:

Size: 3mm
Rated resistance: R25 = 10.0k
B value 25/85 = 3950°K
Rated power: ‰¤ 50mW
Tolerance:± 5%
Operating temperature: from -40°C to +125°C  Tinned steel wire 25mm

The SNZB-02D sensor will monitor temperature and humidity in real time remotely in the application or on the display, with a range of up to 120 metres. The sensor has a built-in intelligent Swiss hygrometer sensor that provides more precise readings, maintaining an accuracy of ±0.2°C/±0.4°F in temperature and ±2% relative humidity in humidity, updating the readings every 5 seconds.

NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance.   Thermistor NTC 100.0K 5% MF52A epoxy resin coating resistor features:

Size: 3mm
Rated resistance: R25 = 100.0k
B value 25/85 = 3950°K
Rated power: ‰¤ 50mW
Tolerance:± 5%
Operating temperature: from -40°C to +125°C  Tinned steel wire 25mm

The solar power management module with the CN3065 chip is ideal for IoT (Internet of Things) projects with renewable energy. Compared to the previous version of the module, improvements have been made to the energy management of the connected battery.

ZPHS01B is an all-in-one air quality module, which integrates laser dust sensor, infrared CO2 sensor, electrochemical formaldehyde, ozone and carbon monoxide sensors, VOC sensor, NO2 sensor, temperature and humidity sensor.