W5500 Ethernet Network Modules SPI 8 sockets

10x Tactile Tact Push Button Switch 6x6x8mm features:

- Tactile Push Tact Switch mini electronic Arduino pushbutton
- Measures: 6x6x8mm
- Quantity: 10 units

This module specially designed for Arduino will allow you to generate a light of any color (RGB) quickly and accurately.
The LED Bulb Module RGB, consisting of an LED capable of creating any color using RGB, has a PWM voltage input with three pins. These are capable of shining in a wide range of colors thanks to the mixture of the three colors. primary (red, green and blue).
These types of diodes are called RGB and are made up of three red, green and blue diodes in the same package.
Thanks to the variation of the intensity of these three diodes, we can create a composition of colors. With this led you can handle more than 16.5 million colors.

It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
L298N Motor Drive Controller Board Module Dual H Bridge DC features:
- Minimum operating voltage: 5 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A
- Logic voltage: 5V
- PWM signal inputs for speed control
- Outputs: for 2 DC motors or for a bipolar stepper motor
- Measures: 43x43x24 mm
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles

The module has two outputs: analog A0 and digital D0.
digital output D0 - signal 0 or 1 appears depending on the configuration of threshold.
The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - digital switching output indicator
- Measurements PCB: 3 x 1.5 cm
- Sensor measurements: 5.4 x 3.9 cm

This external wireless antenna module CC1101 is suitable for Funduino and Arduino projects.
The CC1101 module of 1.2K baud consists of a domestic R & Lotes unit to improve the effective communication distance.
This is a significant improvement over the CC1100 module.
It allows to adjust the speed of the bits for different uses, thus allowing a higher transmission speed.
Supports 2-FSK, GFSK and msk modulations. It also has a high sensitivity (1.2kbps @>

Continous Rotation 360 Degree Servo S3003 features:
- Operating voltage: 4.8 V to 6 V
- Torque max.: 4.1kg / cm (6V)
- Operating speed: 0.23sec / 60degree (4.8V), 0.19sec / 60degree (6V)
- Radio max.: 360º
- Temperature range: -20º + 60ºC degrees
- Weight: 38 g
- Cable length: 26cm
- Dimensions: 40.5 x39x 20 mm
- Servo connector: JR
- Chinese manufacture

- It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader
- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields
Characteristic:
- ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATMega328P
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O pins: 14 (6 with PWM)
- Analog input pins: 6
- DC current for Pin I / O: 20 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P
- SRAM 2 KB - AtMega328P
- EEPROM 1 KB - AtMega328P
- Communication: USB female Type B