Thermistor NTC 100.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 100.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 100.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0092 Available Price €0.29
E18-D80NK Infrared Obstacle Avoidance Sensor Module 3-80cm Smart Car Ideal for projects with ARDUINO, Smart CarDetects transparent and translucent obstaclesE18-D80NK Infrared Obstacle Avoidance Sensor Module 3-80cm Smart Car features:- Current consumption: up to 100 mA- Supply voltage 5V- Current consumption <25mA- Response time of 2 ms- Measured distance: 3-80cm 15st angle- Screw to adjust the sensitivity, the back- Output status led indicator- Operating temperature: -25°C - + 55°C- Material: high-strength plastic- Type of output: normally open, NPN- Dimensions: 18 mm in diameter, Length 45 mm- Cable length 55cm- Departures: - Brown: + - Blue: - - Black: OUT Code S0004 Available Price €5.74
Female DC Power Connector Jack 2.1x5.5mm Jack connectors 2.1mm inside and 5.5mm outside to power devices such as LED strips, CCTV (Cameras), Arduino. Female DC Power Connector Jack 2.1x5.5mm features: - Ideal for connecting without welding- It has two screws in the tip for positive and negative cable screwdriver Code K0050 Available Price €0.40
Battery LIPO 210mAh 3.7V LITHIUM POLYMER BATTERY Battery LIPO 210mAh 3.7V features: -Battery type-lithium polymer. - Type of battery terminals- 3 wires. -Voltage of the battery-3.7 V -Capacity of the battery- 210 mAh. - Embedded PCM security chip (protection against overcharging, over discharge, short circuit) Dimensions: -Length / depth of battery- 25mm -Battery width / diameter- 31 mm It has three cables with a 3-pin connector with a separation of 2 mm. Cables: Red: positive. Black: negative. Yellow: thermistor output. Code PP040 ✗ Out-of-Stock Price €3.13
Fotoboard Pre-Sensitized Photoresist Coated PCB Copper Laminate - One-Sided 10x15cm Fotoboard Pre-Sensitized Photoresist Coated PCB Copper Laminate - One-Sided 10x15cm features:- One side plate for prototype 100x150mm 35um- Fiberglass Code H0164 Available Regular price €3.76 -€0.56 Price €3.20
Flat Cable 1m AWG28 1.27 Gray 10 Pins Flat Cable 1m AWG28 1.27 Gray 10 Pins features: - Length: 100cm - Model AWG28 - Product name: Flat cable - Number of conductors: 10 - Conductive material: Copper - Insulation voltage: 300V - Inner diameter 0.32mm - Pin Pitch: 1.27mm - Temperature: 105 ° C Code K0002 Available Price €2.03
Prototype Breadboard Protoboard 840 points for Arduino Prototype Breadboard Protoboard 840 points Arduino features: - 840 Connections - Linkable with other Boards - Base with adhesive to attach it to the work surface - Measures 165x55x8mm Code PB008 Available Price €2.72
Display OLED 0.96" 128x64 White I2C 4 Pin Display OLED 0.96" 128x64 White I2C 4 Pin features: - Interface: I2C (logical level 3.3V) - Resolution: 128x64 - Angle of view:> 160 degree - Screen color: white - Screen Dimension: 2.43cm / 0.96 " - IC Controller: SSD1306 - Power supply: 3.3V - 5VDC - Operating temperature: -20 ° C - 70 ° C - Size: 2.2x 2.8x 1.2 cm / 0.87x 1.1x 0.47 " - Application: smart watch, MP3, thermometer , instruments, DIY projects, etc ... - It is an OLED display module with white display and with a dot matrix of a resolution 128x64 and an IC2 interface. - The display includes the IC driver SSD1306 128 x 64 OLED / PLED Segment / Common Driver. Code P0091 Available Regular price €5.37 -€2.51 Price €2.86
Timer Relay Module FRM01 The multifunctional relay control module, FRM01, is designed for customers with different synchronization and control needs.The FRM01 is controlled by the STM8S003F3P6 microcontroller and has 18 different functions.Each function can be customized to meet customer needs in a variety of time and power control applications.The FRM01 is equipped with a high-quality power relay, a high-power voltage transistor, red and blue LED indicators, an LED display on a double-sided PCB board.The output of the board is driven by a high quality power relay capable of controlling the AC and DC loads. Timer Relay Module FRM01 features: - Operating voltage: 12 VDC- 4 buttons: SET, SWI, NUM +, NUM-- Operating temperature: -20 °C - + 60 °C Code M0159 Available Regular price €8.22 -€2.00 Price €6.22
WT32-SC01 - ESP32 development board, 3.5 inch LCD touch screen, Wifi Bluetooth WT32-SC01 development board with Esp32 from Espressif. 3.5 inch 480 x 320 TFT LCD touch screen, 4MB SPI Flash and 8MB PSRAM. Code W0129 ✗ Out-of-Stock Price €26.44
USB Type B Female 2.0 Connector Adapter with PCB The USB (Universal Serial Bus), is an industrial standard bus that defines the cables, connectors and protocols used in a bus to connect , communicate and supply power between computers, peripherals and electronic devices. This female type B USB connector adapter soldered on a PCB board is ideal for use in your projects. It has connection points where you can easily solder some pins to connect it directly to a breadboard, or solder a cable over those same connection points. USB Type B Female 2.0 Connector Adapter with PCB features:- Connector type: USB Type B Female, - Internal color: White, - Nominal voltage: 30v DC, - Maximum current: 1A DC, - Insulation resistance: 1000Mohm, - Operating temperature: -25ºC to + 85ºC, Code M0193 Available Regular price €0.83 -€0.10 Price €0.73
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 ✗ Out-of-Stock Price €3.71
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP038 Backorder Price €28.92
SparkFun DataLogger IoT - 9DoF SparkFun DataLogger IoT - 9DoF is a pre-programmed data logger to automatically log IMU, GPS and various pressure, humidity and distance sensors - all without having to write a single line of code! DataLogger automatically detects, configures and logs Qwiic sensors. It is specifically designed for users who only need to capture a large amount of data in a CSV or JSON file and return it to their larger project. Code SP099 Last items in stock Price €77.15
PAM8610 2X10W Dual Channel Amplifier The amplifier with high efficiency, in case of 12 V power supply can output 10 W + 10 W power. Code M0209 Available Price €2.93
16-bit I2C ADS1115 module, 4-channel ADC with professional gain amplifier PGA The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden. Code M0226 Available Price €4.92
W1209 12V DC Thermostat Digital Temperature Controller Switch W1209 12V DC Thermostat Digital Temperature Controller Switch features: - Model: W1209 - Supply voltage: DC 12V - Temperature control mode: ON / OFF - Temperature range: -50 -110 ° C - Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C - Measurement accuracy: 0.1 ° C - Refresh rate: 0.5 s - Temperature protection 0-110 ° C - Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA - Power of output: 10A relay - Sensor probe: NTC waterproof sensor (10K 0.5%) - Environmental requirements: -10 ~ 60 ° C Humidity 20% -85% - Dimensions: 48 x 40 mm Code M0102 Available Price €3.13
Wireless communication module APC220 RF kit APC220 433 MHz long range wireless modules with USB programming interface. The set provides wireless communication with a range of up to 1000 metres. Easy to configure solution for remote control of e.g. a robot. Code W0117 Available Price €35.12
Timer Relay Module FRM01 The multifunctional relay control module, FRM01, is designed for customers with different synchronization and control needs.The FRM01 is controlled by the STM8S003F3P6 microcontroller and has 18 different functions.Each function can be customized to meet customer needs in a variety of time and power control applications.The FRM01 is equipped with a high-quality power relay, a high-power voltage transistor, red and blue LED indicators, an LED display on a double-sided PCB board.The output of the board is driven by a high quality power relay capable of controlling the AC and DC loads. Timer Relay Module FRM01 features: - Operating voltage: 12 VDC- 4 buttons: SET, SWI, NUM +, NUM-- Operating temperature: -20 °C - + 60 °C Code M0159 Available Regular price €8.22 -€2.00 Price €6.22
WT32-SC01 - ESP32 development board, 3.5 inch LCD touch screen, Wifi Bluetooth WT32-SC01 development board with Esp32 from Espressif. 3.5 inch 480 x 320 TFT LCD touch screen, 4MB SPI Flash and 8MB PSRAM. Code W0129 ✗ Out-of-Stock Price €26.44
USB Type B Female 2.0 Connector Adapter with PCB The USB (Universal Serial Bus), is an industrial standard bus that defines the cables, connectors and protocols used in a bus to connect , communicate and supply power between computers, peripherals and electronic devices. This female type B USB connector adapter soldered on a PCB board is ideal for use in your projects. It has connection points where you can easily solder some pins to connect it directly to a breadboard, or solder a cable over those same connection points. USB Type B Female 2.0 Connector Adapter with PCB features:- Connector type: USB Type B Female, - Internal color: White, - Nominal voltage: 30v DC, - Maximum current: 1A DC, - Insulation resistance: 1000Mohm, - Operating temperature: -25ºC to + 85ºC, Code M0193 Available Regular price €0.83 -€0.10 Price €0.73
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 ✗ Out-of-Stock Price €3.71
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP038 Backorder Price €28.92
SparkFun DataLogger IoT - 9DoF SparkFun DataLogger IoT - 9DoF is a pre-programmed data logger to automatically log IMU, GPS and various pressure, humidity and distance sensors - all without having to write a single line of code! DataLogger automatically detects, configures and logs Qwiic sensors. It is specifically designed for users who only need to capture a large amount of data in a CSV or JSON file and return it to their larger project. Code SP099 Last items in stock Price €77.15
PAM8610 2X10W Dual Channel Amplifier The amplifier with high efficiency, in case of 12 V power supply can output 10 W + 10 W power. Code M0209 Available Price €2.93
16-bit I2C ADS1115 module, 4-channel ADC with professional gain amplifier PGA The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden. Code M0226 Available Price €4.92
W1209 12V DC Thermostat Digital Temperature Controller Switch W1209 12V DC Thermostat Digital Temperature Controller Switch features: - Model: W1209 - Supply voltage: DC 12V - Temperature control mode: ON / OFF - Temperature range: -50 -110 ° C - Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C - Measurement accuracy: 0.1 ° C - Refresh rate: 0.5 s - Temperature protection 0-110 ° C - Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA - Power of output: 10A relay - Sensor probe: NTC waterproof sensor (10K 0.5%) - Environmental requirements: -10 ~ 60 ° C Humidity 20% -85% - Dimensions: 48 x 40 mm Code M0102 Available Price €3.13
Wireless communication module APC220 RF kit APC220 433 MHz long range wireless modules with USB programming interface. The set provides wireless communication with a range of up to 1000 metres. Easy to configure solution for remote control of e.g. a robot. Code W0117 Available Price €35.12