Anti-Static Tweezers ESD 135mm Anti-Static Tweezers ESD 135mm features: - Anti-static tweezers, straight tip, matt black- Length: 135mm- Width: 9mm- High precision, without producing dust, resistant to high temperatures Code H0092 Available Price €1.23
ESP32 WROOM-32 DEVKIT V1 - Board with WiFi and Bluetooth WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins. Code W0103 Available Regular price €5.36 -€1.29 Price €4.07
MQ-135 Air Quality Sensor High sensitivity to Ammonia (NH3), Nitrogen oxides (NOx), Alcohol, Sulphides, Benzene (C6H6), CO2, smoke and other harmful gases. The MQ-135 sensor is to sensible for other gasses in the air so that is not possible to get good values for CO2 from it. MQ-135 Air Quality Sensor features:- Main chip: MQ-135 natural gas sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 10ppm - 300ppm NH3 10ppm - 1000ppm Benzene 10ppm - 300ppm Alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0034 ✗ Out-of-Stock Price €2.02
Infrared Receiver VS 1838 38kHz Ideal for projects with ARDUINO, PIC, AVR, Raspberry The infrared receiver receives the signal of 38kHz for remote control Code W0042 Available Price €0.54
Laminated Copper Clad Prototype PCB Circuit Board 30x19cm Laminated Copper Clad Prototype PCB Circuit Board 30x19cm. Code PB033 Backorder Price €4.70
Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor features: - Operating range: 0.2mm to 15mm - Receiver: Phototransistor - Emitter: Infrared Led - Wavelength: 950 nm Code S0026 Available Price €0.41
Module TCRT5000 Infrared Sensor IR Tracker Line Obstacle The optical module sensor (reflective) with comparator LM393, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of a object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver. By using LM393 comparator the module has a binary output (D0) that is at level 1 (object is detected). The sensor allows the detection of an object at a distance of up to 12 mm. Code S0025 Available Price €1.53
Cable chain 15x20 1m for CNC 3D printer Cable chain 15x20 1m for CNC 3D printer features: - Suitable for movements where cable displacement or twisting is needed, where cable protection is needed - Easy for installation And maintenance; Low noise, high speed wear resistant movement - The cable structure has been widely used in CNC machine tools, electronic equipment, fire fighting machinery and equipment, stone machinery, machinery glass, doors and windows of machines, injection molding machines, robots, overweight transport equipment, automated warehouses. - Internal widths 15x20mm - External measurement 20x28mm - Material: reinforced series polyamide - Length: 1m - Quantity: 1 unit Code I0139 Available Price €9.88
2km radius SI4463 433MHz RF Telemetry Arduino compatible A compact, low-power Bottom Effect System Transceiver. Transceiver based on the SI4463 Silicon Labs chip. Industry standard model. In full power operating conditions, open the communication distance up to 2000 km. Much more than the SI4432. Si4463 is a high performance 433 MHz transceiver. and low current consumption of the EZRadioPRO series, which includes a complete transmitter and receiver. Higher sensitivity -126dBm. The maximum output power of + 20dBm, support (G) FSK, 4 (G) FSK, (G) MSK, OOK and ASK modulation. The data rate in the range of 100bps ~ 1Mbps. Operating voltage of 1.8V ~ 3.6V. FCC approval / IC. 2km radius SI4463 433MHz RF Arduino Telemetry features: - Supply voltage: 1.8 ~ 3.6VDC Code W0077 Available Price €5.98
NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA - This module includes PA preamplifier and LNA (Low-noise amplifier)- Comes with the SMA antenna for 2.4GHz (2dB)- Outdoor - transmission up to 250kbps and a distance of up to 1 kilometer- Works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripherals control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA features: * Based on chip NRF24L01 +* Free band: 2.4GHz ISM* Speed: 250kbps, 1Mbps, 2Mbps* Work current- Reception: 45 mA- Transmission: 115 mA (4.2uA -sleep mode)* Receiving sensitivity:-104dB 250kbps- 95dB 1Mbps- 92dB 2Mbps* SPI interface Code W0063 Available Regular price €5.74 -€1.50 Price €4.24
433MHz RF Wireless Receiver + Transmitter Transmitter and receiver kit for radio control and data transmission, compatible with Arduino. 433MHz RF Wireless Receiver + Transmitter features: Specifications of the emitter module: - Power supply: 3V ~ 12V - Working intensity: max = 40mA (at 12V), min = 9mA (at 3V) - AM ASK / OOK modulation - SAW filter - Working frequency: 315MHz-433.92MHz - Transmission power: 25mW (315MHz at 12V) - Range: 20 to 200 meters (different voltages can give different results) - Transfer speed: 4 kB / S - Dimensions: 19x 19x 7mm Receiver module specifications: - Power supply: 5.0VDC + 0.5V - Work intensity: 5.5mA (at 5.0VDC) - Work frequency: 315MHz-433.92MHz - Receiver sensitivity: -100dBm Code W0010 Available Price €0.90
Wireless Transceiver Module with Antenna CC1101 This external wireless antenna module CC1101 is suitable for Funduino and Arduino projects.The CC1101 module of 1.2K baud consists of a domestic R & Lotes unit to improve the effective communication distance.This is a significant improvement over the CC1100 module.It allows to adjust the speed of the bits for different uses, thus allowing a higher transmission speed.Supports 2-FSK, GFSK and msk modulations. It also has a high sensitivity (1.2kbps @> Code W0083 Available Price €7.02
NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino compatible NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0065 ✗ Out-of-Stock Price €1.23
1.5km radius SI4432 433MHz RF Telemetry Transceiver based on the SI4432 Silicon Labs chip Industry standard model Capacitive components manufactured by Murata with 10ppm high precision glass Outdoors - a distance of up to 1.5 km 1.5km radius SI4432 433MHz RF Telemetry features:- Supply voltage: 1.8 ~ 3.6VDC (Note: a voltage higher than 3.6 V will cause permanent damage to the module) - Communication level: 0.7VDC ~ 3.6V (VCC refers to the module supply voltage) - Working frequency: 425M ~ 525MHz (via software setting, the module uses 30M glass) - Measured distance: 1500m (clear and open, maximum power, height 1.5m, air speed 1k) - Transmission power: up to 20dBm (about 100mW) - Air rate: 0.123k ~ 256Kbps (software adjustable, low airspeed recommended) Code W0080 ✗ Out-of-Stock Price €4.12
Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features: - Transceiver based on the SI4432 Silicon Labs chip - Ultrathin ultra small (16.5 × 17 mm) - Good harmonics: easy for FCC / CE certification - Penetration capacity (measured through 8 floors) - Frequency range: 433.92MHz - Sensitivity down to -121 dBm - Maximum output power: 20dBm - Data transfer rate: 0.123-256 kbps - FSK, GFSK and OOK modulation - Power supply: 1.8-3.6 V - Ultra low power shutdown mode - Digital indication of received signal strength (RSSI) - Time to wake up - Bidirectional antenna switch control and automatic adjustment - Configurable packet structure - Preamble detection Code W0075 Available Price €4.12
NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0023 Available Price €1.23
Wireless communication module APC220 RF kit APC220 433 MHz long range wireless modules with USB programming interface. The set provides wireless communication with a range of up to 1000 metres. Easy to configure solution for remote control of e.g. a robot. Code W0117 ✗ Out-of-Stock Price €35.12
NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface features: - Operating voltage: 5V- Wait time of the module receives the data: more than 2S- The waiting time of the module sends data: more than 300- Transfer speed: 50 Byte / S (theoretical value)- I2C / TWI address: 0 x 47 (decimal 35)- Address NRF24L01: 0 x 34, 0 x 43, 0 x 10, 0 x 10, 0 x 01 (from lowest to highest)- Size: 44 x 23 mm Code W0066 Available Price €3.69
2km radius SI4463 433MHz RF Telemetry Arduino compatible A compact, low-power Bottom Effect System Transceiver. Transceiver based on the SI4463 Silicon Labs chip. Industry standard model. In full power operating conditions, open the communication distance up to 2000 km. Much more than the SI4432. Si4463 is a high performance 433 MHz transceiver. and low current consumption of the EZRadioPRO series, which includes a complete transmitter and receiver. Higher sensitivity -126dBm. The maximum output power of + 20dBm, support (G) FSK, 4 (G) FSK, (G) MSK, OOK and ASK modulation. The data rate in the range of 100bps ~ 1Mbps. Operating voltage of 1.8V ~ 3.6V. FCC approval / IC. 2km radius SI4463 433MHz RF Arduino Telemetry features: - Supply voltage: 1.8 ~ 3.6VDC Code W0077 Available Price €5.98
NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA - This module includes PA preamplifier and LNA (Low-noise amplifier)- Comes with the SMA antenna for 2.4GHz (2dB)- Outdoor - transmission up to 250kbps and a distance of up to 1 kilometer- Works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripherals control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA features: * Based on chip NRF24L01 +* Free band: 2.4GHz ISM* Speed: 250kbps, 1Mbps, 2Mbps* Work current- Reception: 45 mA- Transmission: 115 mA (4.2uA -sleep mode)* Receiving sensitivity:-104dB 250kbps- 95dB 1Mbps- 92dB 2Mbps* SPI interface Code W0063 Available Regular price €5.74 -€1.50 Price €4.24
433MHz RF Wireless Receiver + Transmitter Transmitter and receiver kit for radio control and data transmission, compatible with Arduino. 433MHz RF Wireless Receiver + Transmitter features: Specifications of the emitter module: - Power supply: 3V ~ 12V - Working intensity: max = 40mA (at 12V), min = 9mA (at 3V) - AM ASK / OOK modulation - SAW filter - Working frequency: 315MHz-433.92MHz - Transmission power: 25mW (315MHz at 12V) - Range: 20 to 200 meters (different voltages can give different results) - Transfer speed: 4 kB / S - Dimensions: 19x 19x 7mm Receiver module specifications: - Power supply: 5.0VDC + 0.5V - Work intensity: 5.5mA (at 5.0VDC) - Work frequency: 315MHz-433.92MHz - Receiver sensitivity: -100dBm Code W0010 Available Price €0.90
Wireless Transceiver Module with Antenna CC1101 This external wireless antenna module CC1101 is suitable for Funduino and Arduino projects.The CC1101 module of 1.2K baud consists of a domestic R & Lotes unit to improve the effective communication distance.This is a significant improvement over the CC1100 module.It allows to adjust the speed of the bits for different uses, thus allowing a higher transmission speed.Supports 2-FSK, GFSK and msk modulations. It also has a high sensitivity (1.2kbps @> Code W0083 Available Price €7.02
NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino compatible NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0065 ✗ Out-of-Stock Price €1.23
1.5km radius SI4432 433MHz RF Telemetry Transceiver based on the SI4432 Silicon Labs chip Industry standard model Capacitive components manufactured by Murata with 10ppm high precision glass Outdoors - a distance of up to 1.5 km 1.5km radius SI4432 433MHz RF Telemetry features:- Supply voltage: 1.8 ~ 3.6VDC (Note: a voltage higher than 3.6 V will cause permanent damage to the module) - Communication level: 0.7VDC ~ 3.6V (VCC refers to the module supply voltage) - Working frequency: 425M ~ 525MHz (via software setting, the module uses 30M glass) - Measured distance: 1500m (clear and open, maximum power, height 1.5m, air speed 1k) - Transmission power: up to 20dBm (about 100mW) - Air rate: 0.123k ~ 256Kbps (software adjustable, low airspeed recommended) Code W0080 ✗ Out-of-Stock Price €4.12
Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features: - Transceiver based on the SI4432 Silicon Labs chip - Ultrathin ultra small (16.5 × 17 mm) - Good harmonics: easy for FCC / CE certification - Penetration capacity (measured through 8 floors) - Frequency range: 433.92MHz - Sensitivity down to -121 dBm - Maximum output power: 20dBm - Data transfer rate: 0.123-256 kbps - FSK, GFSK and OOK modulation - Power supply: 1.8-3.6 V - Ultra low power shutdown mode - Digital indication of received signal strength (RSSI) - Time to wake up - Bidirectional antenna switch control and automatic adjustment - Configurable packet structure - Preamble detection Code W0075 Available Price €4.12
NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0023 Available Price €1.23
Wireless communication module APC220 RF kit APC220 433 MHz long range wireless modules with USB programming interface. The set provides wireless communication with a range of up to 1000 metres. Easy to configure solution for remote control of e.g. a robot. Code W0117 ✗ Out-of-Stock Price €35.12
NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface features: - Operating voltage: 5V- Wait time of the module receives the data: more than 2S- The waiting time of the module sends data: more than 300- Transfer speed: 50 Byte / S (theoretical value)- I2C / TWI address: 0 x 47 (decimal 35)- Address NRF24L01: 0 x 34, 0 x 43, 0 x 10, 0 x 10, 0 x 01 (from lowest to highest)- Size: 44 x 23 mm Code W0066 Available Price €3.69