ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.61
LM35DZ Temperature Sensor TO-92 LM35 Temperature Sensor LM35DZ TO92 features:- The output is linear and each degree Celsius equals 10 mV- Power supply from 4 to 30 Vdc- Connection through analog input- Temperature range from 0ºC to 100ºC- Linearity +10 mV / ºC- Quantity: 1 unit Code S0016 Available Price €2.06
BME280 Digital Temperature Humidity Barometric Pressure Module This module includes the component BME280 that is translated into a digital signal.The equipment uses the two I2C and SPI interfaces. The BME280 does not allow the module to be used as an altimeter as opposed to its successor BMP280.Its 5-pin straight connector allows easy connection to other electronic boards. BME280 Digital Temperature Humidity Barometric Pressure Module features: - Interfaces:- I2C (up to 3.4 MHz)- SPI (up to 10 MHz)- Supply voltage: 1.8-5VDC- Module operating range:- Temperature: -40ºC to + 85ºC- Humidity: 0-100%- Pressure: 300-1100 hPa- Resolution of the measures:- Temperature: 0.01ºC- Humidity: 0.008%- Pressure: 0. 18Pa- Accuracy of the measures:- Temperature: +/> Code M0135 ✗ Out-of-Stock Regular price €9.88 -€5.00 Price €4.88
10x Electrolytic Capacitor 470uF 16V 105ºC 10x Electrolytic Capacitor 470uF 16V 105ºC PIC Arduino features:-Type: Electrolytic Capacitor-Assembly: intern-Value: 470uF-Maximum tension: 16V-Maximum temperature 105º C-Dimensions: 8x12mm-Quantity: 10 units Code D0047 Available Price €0.11
VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features: > - Input voltage 2.5V-3V - Operating power 60mW / 15fps VGA YUV - Resolution VGA 640x480 pixels (30fps) - Maximum frame rate 30fps VGA - Flicker 50Hz / 60Hz automatic detection - Lens size 1/6 " - Angle of view 25 ° - Sensitivity 1.3V / (lux- seg) - SCCB (Serial Camera Control Bus) interface - Output format · 8 Bits - YUV / YCbCr 4: 2: 2 - RGB 565/555/444 - GRB 4: 2: 2 - RAW RGB data - High sensitivity Light operation - Automatic adjustment - Color level saturation - Edge enhancement - Noise level Code M0103 Available Regular price €4.79 -€1.00 Price €3.79
Solder Wire Tin Sn60Pb40 Lead 2.5% Flux 0.56mm 100g Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 0.56mm features: - 100gr. 0.56mm diameter welding wire. 60% tin and 40% lead- Fusing temperature 183 „ƒ / 190 „ƒ- Alloy Sn60 Pb40- Flux 2.5%- Quantity: 1 unit Code Q0103 Available Price €7.40
16x2 LCD screen 1602 Blue welded pins It consists of a 16-character, 2-row display The display is compatible with the HD44780 controller Ideal for projects with Arduino You can use it with PIC, AVR, STM32 16x2 LCD screen 1602 Blue welded pins features: - LCD screen, 16 characters and 2 lines - 5V power supply - HD44780 compatible controller - Backlit blue background, white letters - Includes an adjustable contrast pin - It has soldered pins and is ready to connect - Dimensions (mm): 80 x 36 x 19 Code P0154 Available Price €3.26
GPS Mini Station NEO-6M-0-001 with EEPROM SMA IPEX Ports It is a mini GPS module including a NEO-6M chip and an EEPROM memory chip. The SMA antenna port is On-board IPEX and cell phone button battery ensure robust positioning efficiency and fast satellite discovery speed. Serial port provides simple initial knowledge to stay in touch with the most compatible Arduino-compatible MCU STM32. Characteristic: - Supply voltage: 3.3 - 5 VDC - Operating current: 45 mA - Communication speed: 9600 Bauds configurable from 4800 to 115200 Bauds - Navigation update: 5 Hz max. (1 Hz default) - Capture time: at the start 27s, in operation 1s - Operating temperature: -40 ° C - + 85 ° C - separate GPS antenna (not included ): 18x18 mm - Size: 22x30x13 mm Code M0070 ✗ Out-of-Stock Price €12.31
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 ✗ Out-of-Stock Price €3.71
ESP32-CAM WiFi Camera + Bluetooth Module The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot. Code W0100 ✗ Out-of-Stock Price €7.81
A6 GSM GPRS Four Band GPRS Module with MCU Antenna GSM A6 Four Band GPRS Module with MCU Antenna features: - GSM / GPRS module / development board / shield based on GPRS A6 - Supports GSM / Dual band GPRS, available for remote GPRS and SMS data transmission - Compact size and low current consumption - With energy saving technique, current consumption is as low as 5mA (sleep mode) - Communicates with the microcontroller through the UART port, supports the command including GSM 07.07, GSM 07.05 and Ai-Thinker Enhanced AT Commands - Working frequency: four-band network, 850 / 900/1800 / 1900MHz - Operating voltage: 4.8-9VDC (Supply power of the on-board regulator circuit for the A6 module) - Working current: 2A maximum - Current Sleep: 5mA Code W0062 Available Price €11.98
RFID PN532 NFC Module with Card and Pendant NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module with Card and Pendant features: - Support i2C, SPI, High Speed UART - Support RFID reading and writing - Support P2P communication with peers - Support NFC with phone - Work in NFC Mode or RFID reader/writer Mode - RFID reader/writer supports: - 1k, 4k, Ultralight, and DesFire cards ISO/> Code W0091 Available Price €8.26
ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu Allows control: - Up to 2 bidirectional current motors- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A- Logic voltage: - 2.3V <= HIV <= VIN (high) - 0.3V <= VIL <= 1.5V (low)- Controller L293D- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA- D2, D4 - motorB Code W0015 Available Price €2.88
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP038 Backorder Price €28.92
WT32-SC01 - ESP32 development board, 3.5 inch LCD touch screen, Wifi Bluetooth WT32-SC01 development board with Esp32 from Espressif. 3.5 inch 480 x 320 TFT LCD touch screen, 4MB SPI Flash and 8MB PSRAM. Code W0129 ✗ Out-of-Stock Price €26.44
Adapter SMA Female GPS GSM IPEX 2.4 Ghz RF ESP8266 1.13mm 50 Ohm Can be connected with the ESP8266 module with IPEXCompatible with Hirose U.FL and IPEX MHF1 Adapter SMA Female GPS GSM IPEX 2.4 Ghz RF ESP8266 1.13mm 50 Ohm features: - Frequency range: 0 ~ 6000MHz- Interface: SMA female connector- IPEX female connector- Cable length: 15cm- Coaxial cable: 1,13mm- V.S.W.R.: <1.5- Impedance (ohm): 50- Maximum input power (W): 50W- Operating temperature: -40ºC ~ + 70ºC Code W0071 Available Price €1.81
ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0014 Available Price €4.09
Low Loss Coax Cable H-155 2.4GHz WiFi LTE GSM Low Loss Coax Cable H-155 2.4GHz WiFi LTE GSM features:- The cable is used for system transmissions2.4 [GHz] (WiFi, LTE, 3G, GPS)- It is also suitable for the lower frequencies (CB, GSM, PMR)- It has less loss than the type RG-58 cable- Type of coaxial cable- H155 cable series- 50Ω wave impedance- Stranded core structure- Core type Cu- Structure of the laminated Al-PET shield, tinned copper braid- PVC external insulation material- Gray insulation color- Outer cable dimensions Ø5.4mm- Operating temperature -15 ... 70 ° C- Resistance to weather conditions- Installation of 2.4 GHz antenna cable, outdoor- Attenuations [dB / 100m]:* 50 [MHz] - 6.5* 100 [MHz] - 9.3 Code K0056 Available Price €2.31
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 ✗ Out-of-Stock Price €3.71
ESP32-CAM WiFi Camera + Bluetooth Module The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot. Code W0100 ✗ Out-of-Stock Price €7.81
A6 GSM GPRS Four Band GPRS Module with MCU Antenna GSM A6 Four Band GPRS Module with MCU Antenna features: - GSM / GPRS module / development board / shield based on GPRS A6 - Supports GSM / Dual band GPRS, available for remote GPRS and SMS data transmission - Compact size and low current consumption - With energy saving technique, current consumption is as low as 5mA (sleep mode) - Communicates with the microcontroller through the UART port, supports the command including GSM 07.07, GSM 07.05 and Ai-Thinker Enhanced AT Commands - Working frequency: four-band network, 850 / 900/1800 / 1900MHz - Operating voltage: 4.8-9VDC (Supply power of the on-board regulator circuit for the A6 module) - Working current: 2A maximum - Current Sleep: 5mA Code W0062 Available Price €11.98
RFID PN532 NFC Module with Card and Pendant NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module with Card and Pendant features: - Support i2C, SPI, High Speed UART - Support RFID reading and writing - Support P2P communication with peers - Support NFC with phone - Work in NFC Mode or RFID reader/writer Mode - RFID reader/writer supports: - 1k, 4k, Ultralight, and DesFire cards ISO/> Code W0091 Available Price €8.26
ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu Allows control: - Up to 2 bidirectional current motors- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A- Logic voltage: - 2.3V <= HIV <= VIN (high) - 0.3V <= VIL <= 1.5V (low)- Controller L293D- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA- D2, D4 - motorB Code W0015 Available Price €2.88
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP038 Backorder Price €28.92
WT32-SC01 - ESP32 development board, 3.5 inch LCD touch screen, Wifi Bluetooth WT32-SC01 development board with Esp32 from Espressif. 3.5 inch 480 x 320 TFT LCD touch screen, 4MB SPI Flash and 8MB PSRAM. Code W0129 ✗ Out-of-Stock Price €26.44
Adapter SMA Female GPS GSM IPEX 2.4 Ghz RF ESP8266 1.13mm 50 Ohm Can be connected with the ESP8266 module with IPEXCompatible with Hirose U.FL and IPEX MHF1 Adapter SMA Female GPS GSM IPEX 2.4 Ghz RF ESP8266 1.13mm 50 Ohm features: - Frequency range: 0 ~ 6000MHz- Interface: SMA female connector- IPEX female connector- Cable length: 15cm- Coaxial cable: 1,13mm- V.S.W.R.: <1.5- Impedance (ohm): 50- Maximum input power (W): 50W- Operating temperature: -40ºC ~ + 70ºC Code W0071 Available Price €1.81
ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0014 Available Price €4.09
Low Loss Coax Cable H-155 2.4GHz WiFi LTE GSM Low Loss Coax Cable H-155 2.4GHz WiFi LTE GSM features:- The cable is used for system transmissions2.4 [GHz] (WiFi, LTE, 3G, GPS)- It is also suitable for the lower frequencies (CB, GSM, PMR)- It has less loss than the type RG-58 cable- Type of coaxial cable- H155 cable series- 50Ω wave impedance- Stranded core structure- Core type Cu- Structure of the laminated Al-PET shield, tinned copper braid- PVC external insulation material- Gray insulation color- Outer cable dimensions Ø5.4mm- Operating temperature -15 ... 70 ° C- Resistance to weather conditions- Installation of 2.4 GHz antenna cable, outdoor- Attenuations [dB / 100m]:* 50 [MHz] - 6.5* 100 [MHz] - 9.3 Code K0056 Available Price €2.31