1.5km radius SI4432 433MHz RF Telemetry

It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
L298N Motor Drive Controller Board Module Dual H Bridge DC features:
- Minimum operating voltage: 5 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A
- Logic voltage: 5V
- PWM signal inputs for speed control
- Outputs: for 2 DC motors or for a bipolar stepper motor
- Measures: 43x43x24 mm
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles

NodeMcu module based on ESP8266 controller and programming in Lua language.
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC.
ESP8266-12E is an improved version of ESP8266-12.
It works as a standard WiFi 802.11 b / g / n 2.4 GHz.
USB communication - the CH340 chip. Characteristics of ESP 12E:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- TCP Stack / Integrated IP
- PLLs, Regulators and Integrated Power Management Units
- Output Power: 0.15 (W); + 19.5dBm in 802.11b mode

Driver DRV8833 can control up to two DC motors or one stepper motor with a constant current of 1.5 A (peak 4A ). The motors are controlled, independently by means of PWM signals the direction of rotation of the motors can be controlled, neutral or stop with a frequency of up to 100 kHz. Two input signals (IN1 and IN2) can be used to control one motor (connected to OUT1 and OUT2) and the other two input signals (IN3 and IN4) to control the second motor (connected to OUT3 and OUT4). NOTE: This DRV8833 dual-bridge motor controller is the replacement for the TB6612FNG dual-channel motor controller. The pins come unsoldered. If the motor draws currents above 0.6A, the use of a heat sink may be required. DRV8833 Controller DC Motor PAP features:

High sensitivity to Ammonia (NH3), Nitrogen oxides (NOx), Alcohol, Sulphides, Benzene (C6H6), CO2, smoke and other harmful gases.  The MQ-135 sensor is to sensible for other gasses in the air so that is not possible to get good values for CO2 from it.
MQ-135 Air Quality Sensor features:
- Main chip: MQ-135 natural gas sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
   10ppm - 300ppm NH3
   10ppm - 1000ppm Benzene
   10ppm - 300ppm Alcohol
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

Led Matrix 8x8 MAX7219 Soldier features:
- MAX7219 controller module with 8x8 led matrix + cables
- 8X8 LED matrix controlled by MAX7219 chip
- Led 3mm red color
- SPI communication
- Voltage: 4.7 - 5.3V DC
- Interfaces to manage multiple modules in cascade
- Matrix dimensions: 32mm x 32mm x 8mm
- PCB dimensions: 32mm x 50mm

- The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values ​​and measures tenths of a degree
Characteristic:
- Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy
- Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy
- Maximum sampling rate: 2 seconds
Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards:
Write texts on the OLED 0.96 '' screen
- Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen
Send />

The bluetooth HC-05 module is one of the best options for projects where you need wireless communications.
The transceiver module (transmission / reception) allows bluetooth wireless connections as master or slave, works transparently as if making a wired RS-232 TTL serial connection. Arduino Wireless Module HC-05 HC05 Bluetooth features:
- CSR BC417 Chipset
- Power: 3.3.
- Bluetooth version V2.0 + EDR
- Frequency: 2.4GHz ISM band
- Modulation: GFSK
- Approximate range: 10m
- Security: Authentication and encryption
- Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps
- Supports AT commands for configuration through a serial port
temperature: -20 ºC to +75 ºC

- WIFI module based on the ESP8266 controller
- ESP8266-12F is an improved version of ESP8266-12E
- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated
ESP-12F ESP8266 12F WiFi Board Module features:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP Stack.
- PLL, regulators and integrated energy management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low energy mode: <10 uA
- Integrated 32-bit processor