Battery holder 2x 18650 PCB mount Base of two 18650 batteries to solder on PCB. Characteristic: - Measurements 78x 40x 21mm - Weight: 10 gr . (approx.) - Stack length max 67mm Code PP052 Available Price €2.49
Prototype Board Transparent 400 points It can be used to work with AVR, ARM, PIC microcontrollers, Arduino modules and to work with self-designed prototypes. Prototype Board Transparent 400 points features: - Linkable with other plates - Base with adhesive - 400 contacts without welding (300 contacts for components and 100 contacts for power rails ) - Transparent ABS - Measurements 82x 55x 8 mm Code PB003 Available Price €1.90
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €3.09
40x Male to male cables 10cm 40x Male to male cables 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont male connectors on both ends - Compatible with 2.54mm female connectors - High quality and good working condition - Easy to install and use Code K0107 Backorder Price €1.99
2 Double Side Prototype PCB Board 3x7cm 2 Double Side Prototype PCB Board 3x7cm features: -Thickness of PCB: 1.6mm-Material: high quality FR-4 glass fiber PCB-Presented and numbered on both sides-Top and bottom are identical copper layers-Pads grid (pitch) 2.54mm/0.1", hole diameter 0.9mm Code PB025 Available Price €0.69
MH-Z19C Infrared Sensor module 5000ppm CO2 monitor HVAC PWM output UART CO2 sensor model MH-Z19C. High precision working voltage 5.0±0.1V DC. The measuring range is between 0 and 5000 ppm. It has a low power consumption. UART and PWM output. Code S0044 Available Price €29.49
Bluetooth Transceiver Module HC-05 Wireless - HC-05 Bluetooth transceiver module with base- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.Bluetooth Transceiver Module HC-05 Wireless features:- Chipset CSR BC417- 3.6 to 6 Vdc power supply- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps Code W0004 Available Price €5.39
RFID PN532 NFC Module with Card and Pendant NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module with Card and Pendant features: - Support i2C, SPI, High Speed UART - Support RFID reading and writing - Support P2P communication with peers - Support NFC with phone - Work in NFC Mode or RFID reader/writer Mode - RFID reader/writer supports: - 1k, 4k, Ultralight, and DesFire cards ISO/> Code W0091 Available Price €9.99
NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA - This module includes PA preamplifier and LNA (Low-noise amplifier)- Comes with the SMA antenna for 2.4GHz (2dB)- Outdoor - transmission up to 250kbps and a distance of up to 1 kilometer- Works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripherals control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA features: * Based on chip NRF24L01 +* Free band: 2.4GHz ISM* Speed: 250kbps, 1Mbps, 2Mbps* Work current- Reception: 45 mA- Transmission: 115 mA (4.2uA -sleep mode)* Receiving sensitivity:-104dB 250kbps- 95dB 1Mbps- 92dB 2Mbps* SPI interface Code W0063 Available Price €6.95
2km radius SI4463 433MHz RF Telemetry Arduino compatible A compact, low-power Bottom Effect System Transceiver. Transceiver based on the SI4463 Silicon Labs chip. Industry standard model. In full power operating conditions, open the communication distance up to 2000 km. Much more than the SI4432. Si4463 is a high performance 433 MHz transceiver. and low current consumption of the EZRadioPRO series, which includes a complete transmitter and receiver. Higher sensitivity -126dBm. The maximum output power of + 20dBm, support (G) FSK, 4 (G) FSK, (G) MSK, OOK and ASK modulation. The data rate in the range of 100bps ~ 1Mbps. Operating voltage of 1.8V ~ 3.6V. FCC approval / IC. 2km radius SI4463 433MHz RF Arduino Telemetry features: - Supply voltage: 1.8 ~ 3.6VDC Code W0077 Available Price €7.24
NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0023 Available Price €1.49
NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface features: - Operating voltage: 5V- Wait time of the module receives the data: more than 2S- The waiting time of the module sends data: more than 300- Transfer speed: 50 Byte / S (theoretical value)- I2C / TWI address: 0 x 47 (decimal 35)- Address NRF24L01: 0 x 34, 0 x 43, 0 x 10, 0 x 10, 0 x 01 (from lowest to highest)- Size: 44 x 23 mm Code W0066 Available Price €4.46
Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features: - Transceiver based on the SI4432 Silicon Labs chip - Ultrathin ultra small (16.5 × 17 mm) - Good harmonics: easy for FCC / CE certification - Penetration capacity (measured through 8 floors) - Frequency range: 433.92MHz - Sensitivity down to -121 dBm - Maximum output power: 20dBm - Data transfer rate: 0.123-256 kbps - FSK, GFSK and OOK modulation - Power supply: 1.8-3.6 V - Ultra low power shutdown mode - Digital indication of received signal strength (RSSI) - Time to wake up - Bidirectional antenna switch control and automatic adjustment - Configurable packet structure - Preamble detection Code W0075 Available Price €4.99
433MHz RF Wireless Receiver + Transmitter Transmitter and receiver kit for radio control and data transmission, compatible with Arduino. 433MHz RF Wireless Receiver + Transmitter features: Specifications of the emitter module: - Power supply: 3V ~ 12V - Working intensity: max = 40mA (at 12V), min = 9mA (at 3V) - AM ASK / OOK modulation - SAW filter - Working frequency: 315MHz-433.92MHz - Transmission power: 25mW (315MHz at 12V) - Range: 20 to 200 meters (different voltages can give different results) - Transfer speed: 4 kB / S - Dimensions: 19x 19x 7mm Receiver module specifications: - Power supply: 5.0VDC + 0.5V - Work intensity: 5.5mA (at 5.0VDC) - Work frequency: 315MHz-433.92MHz - Receiver sensitivity: -100dBm Code W0010 Available Price €1.09
1.5km radius SI4432 433MHz RF Telemetry Transceiver based on the SI4432 Silicon Labs chip Industry standard model Capacitive components manufactured by Murata with 10ppm high precision glass Outdoors - a distance of up to 1.5 km 1.5km radius SI4432 433MHz RF Telemetry features:- Supply voltage: 1.8 ~ 3.6VDC (Note: a voltage higher than 3.6 V will cause permanent damage to the module) - Communication level: 0.7VDC ~ 3.6V (VCC refers to the module supply voltage) - Working frequency: 425M ~ 525MHz (via software setting, the module uses 30M glass) - Measured distance: 1500m (clear and open, maximum power, height 1.5m, air speed 1k) - Transmission power: up to 20dBm (about 100mW) - Air rate: 0.123k ~ 256Kbps (software adjustable, low airspeed recommended) Code W0080 Available Price €4.99
NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino compatible NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0065 Backorder Price €1.49
Wireless communication module APC220 RF kit APC220 433 MHz long range wireless modules with USB programming interface. The set provides wireless communication with a range of up to 1000 metres. Easy to configure solution for remote control of e.g. a robot. Code W0117 Available Price €45.90
NRF24L01 + Wireless Transceiver Module 2.4GHz It is ultra compact and very low consumption. It works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripheral control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Transceiver Module 2.4GHz features: - Based on chip NRF24L01 + Ultra Low Power- Free band: 2.4GHz ISM- Speed: 250kbps, 1Mbps, 2Mbps- Working current - reception: 13 mA- Transmission: 11 mA (900nA -deep sleep mode)- Receiving sensitivity: -94dB 250kbps- Coverage in closed spaces: 15m / 30m- SPI interface- Input voltage: 1.9V- 3.6V- Input / output port voltage: 0V-3.3V / 5V- Coverage in open areas: 100m approx.- Clock frequency: 16MHz Code W0005 Available Price €1.59
NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA - This module includes PA preamplifier and LNA (Low-noise amplifier)- Comes with the SMA antenna for 2.4GHz (2dB)- Outdoor - transmission up to 250kbps and a distance of up to 1 kilometer- Works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripherals control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA features: * Based on chip NRF24L01 +* Free band: 2.4GHz ISM* Speed: 250kbps, 1Mbps, 2Mbps* Work current- Reception: 45 mA- Transmission: 115 mA (4.2uA -sleep mode)* Receiving sensitivity:-104dB 250kbps- 95dB 1Mbps- 92dB 2Mbps* SPI interface Code W0063 Available Price €6.95
2km radius SI4463 433MHz RF Telemetry Arduino compatible A compact, low-power Bottom Effect System Transceiver. Transceiver based on the SI4463 Silicon Labs chip. Industry standard model. In full power operating conditions, open the communication distance up to 2000 km. Much more than the SI4432. Si4463 is a high performance 433 MHz transceiver. and low current consumption of the EZRadioPRO series, which includes a complete transmitter and receiver. Higher sensitivity -126dBm. The maximum output power of + 20dBm, support (G) FSK, 4 (G) FSK, (G) MSK, OOK and ASK modulation. The data rate in the range of 100bps ~ 1Mbps. Operating voltage of 1.8V ~ 3.6V. FCC approval / IC. 2km radius SI4463 433MHz RF Arduino Telemetry features: - Supply voltage: 1.8 ~ 3.6VDC Code W0077 Available Price €7.24
NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0023 Available Price €1.49
NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface features: - Operating voltage: 5V- Wait time of the module receives the data: more than 2S- The waiting time of the module sends data: more than 300- Transfer speed: 50 Byte / S (theoretical value)- I2C / TWI address: 0 x 47 (decimal 35)- Address NRF24L01: 0 x 34, 0 x 43, 0 x 10, 0 x 10, 0 x 01 (from lowest to highest)- Size: 44 x 23 mm Code W0066 Available Price €4.46
Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features: - Transceiver based on the SI4432 Silicon Labs chip - Ultrathin ultra small (16.5 × 17 mm) - Good harmonics: easy for FCC / CE certification - Penetration capacity (measured through 8 floors) - Frequency range: 433.92MHz - Sensitivity down to -121 dBm - Maximum output power: 20dBm - Data transfer rate: 0.123-256 kbps - FSK, GFSK and OOK modulation - Power supply: 1.8-3.6 V - Ultra low power shutdown mode - Digital indication of received signal strength (RSSI) - Time to wake up - Bidirectional antenna switch control and automatic adjustment - Configurable packet structure - Preamble detection Code W0075 Available Price €4.99
433MHz RF Wireless Receiver + Transmitter Transmitter and receiver kit for radio control and data transmission, compatible with Arduino. 433MHz RF Wireless Receiver + Transmitter features: Specifications of the emitter module: - Power supply: 3V ~ 12V - Working intensity: max = 40mA (at 12V), min = 9mA (at 3V) - AM ASK / OOK modulation - SAW filter - Working frequency: 315MHz-433.92MHz - Transmission power: 25mW (315MHz at 12V) - Range: 20 to 200 meters (different voltages can give different results) - Transfer speed: 4 kB / S - Dimensions: 19x 19x 7mm Receiver module specifications: - Power supply: 5.0VDC + 0.5V - Work intensity: 5.5mA (at 5.0VDC) - Work frequency: 315MHz-433.92MHz - Receiver sensitivity: -100dBm Code W0010 Available Price €1.09
1.5km radius SI4432 433MHz RF Telemetry Transceiver based on the SI4432 Silicon Labs chip Industry standard model Capacitive components manufactured by Murata with 10ppm high precision glass Outdoors - a distance of up to 1.5 km 1.5km radius SI4432 433MHz RF Telemetry features:- Supply voltage: 1.8 ~ 3.6VDC (Note: a voltage higher than 3.6 V will cause permanent damage to the module) - Communication level: 0.7VDC ~ 3.6V (VCC refers to the module supply voltage) - Working frequency: 425M ~ 525MHz (via software setting, the module uses 30M glass) - Measured distance: 1500m (clear and open, maximum power, height 1.5m, air speed 1k) - Transmission power: up to 20dBm (about 100mW) - Air rate: 0.123k ~ 256Kbps (software adjustable, low airspeed recommended) Code W0080 Available Price €4.99
NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino compatible NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0065 Backorder Price €1.49
Wireless communication module APC220 RF kit APC220 433 MHz long range wireless modules with USB programming interface. The set provides wireless communication with a range of up to 1000 metres. Easy to configure solution for remote control of e.g. a robot. Code W0117 Available Price €45.90
NRF24L01 + Wireless Transceiver Module 2.4GHz It is ultra compact and very low consumption. It works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripheral control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Transceiver Module 2.4GHz features: - Based on chip NRF24L01 + Ultra Low Power- Free band: 2.4GHz ISM- Speed: 250kbps, 1Mbps, 2Mbps- Working current - reception: 13 mA- Transmission: 11 mA (900nA -deep sleep mode)- Receiving sensitivity: -94dB 250kbps- Coverage in closed spaces: 15m / 30m- SPI interface- Input voltage: 1.9V- 3.6V- Input / output port voltage: 0V-3.3V / 5V- Coverage in open areas: 100m approx.- Clock frequency: 16MHz Code W0005 Available Price €1.59