TPA3116D2 Class D 2X50W Dual Channel Amplifier

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins.

The piezoelectric buzzer has a simple structure in which a ceramic piezoelectric disk is affixed to a vibrating plate. An alternative voltage applied to this element will cause a contraction or diametrical expansion of the element. This feature is used to fold a vibrating plate, which generates sounds. Passive Buzzer 5V features:

- Input voltage: 3V to 12V
- Diameter: 12mm
- Height: 7.5mm
- Pin spacing: 6.5mm
- Impedance: 16 Ohm
- Working frequency: 2 to 5 KHz
- Quantity: 1 unit

 Master Slave Bluetooth Modul for Arduino iOS Android. The HM10 supports Bluetooth 4.0 (low energy) and therefore has a relatively low power consumption.

APC220 433 MHz long range wireless modules with USB programming interface. The set provides wireless communication with a range of up to 1000 metres. Easy to configure solution for remote control of e.g. a robot.

- HC-05 Bluetooth transceiver module with base
- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.
- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.
Bluetooth Transceiver Module HC-05 Wireless features:
- Chipset CSR BC417
- 3.6 to 6 Vdc power supply
- Bluetooth version V2.0 + EDR
- Frequency: 2.4GHz ISM band
- Modulation: GFSK
- Reach approx. 10m
- Security: Authentication and encryption.
- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps

WiFi Smart Wall Switch Sonoff T1 Gang 86

Smart WiFi RF APP Touch Control Wall Light Switch features:
works with Amazon Alexa,  Google Assistant DIY Smart Home, Nest  via iPhone Android.

SONOFF D1 Smart Dimmer Switch is a smart dimmer switch that offers smart light control solutions perfect for your home or workplace, controlled either by the eWeLink application, via 433MHz RF control or by voice assistants such as Alexa or Google Home.

Create your own scenes, turn the light on at the most appropriate level, or schedule it at the times you want

This module is used to extend the Raspberry's 40 GPIO pins to another set of 2x20 male pins and 8 parallel pins accessible on the terminal blocks in the that test leads are pushed. The electronic board offers great reliability with the Raspberry and is very easy to connect thanks to its existing suitable accessories but not included.
The module offers a set of mini jumpers to configure the GPIO.

XY-V17B is a smart voice module, integrated IO segment trigger, control UART series, ONE_line control of a single serial bus, MP3 standard and other functions; Supports MP3, WAV format decoding, maximum storage capacity on 32G TF card, update audio files from TF memory card via USB data cable to connect computer.
Voice Module MP3 Player features:

- Support MP3, WAV decoder format.
- Support sample rate ( KHz): 8 / 11.025 / 12/16 / 22.05 / 24/32 / 44.1 / 48.
- 24-bit DAC output, support 90dB dynamic range, support 85dB signal-to-noise ratio.
- Fully compatible with FAT16 / FAT32 file system, 32G TF card with maximum support, 32G U disk support.