ESP8266 5V WiFi Relay Module AP Remote Control + STA

40x Female-Female Cable 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Dupont female connectors on both ends
- Compatible with 2.54mm male connectors
- High quality and good working conditions
- Easy to install and use

It has an ON / OFF switch that will cut off power when you don't need it.
USB to Micro USB On/Off Switch Arduino Charger Cable features:
- Black color
- Length: 150cm
- Maximum current 1A

A virtual serial port to your PC through the USB port. FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable features:
- USB-Serial TTL 3.3V -5V Converter
- LED indicator for Tx, Rx, power supply
- Communication: Transceiver RX / TX TTL COM Virtual RS232
- Voltage: 3.3V or 5V - via jumper
- Pins: DTR, RX, TX, VCC, CTS, GND
- Protections: Electronic fuse up to 500mA
- Size: 35 x 17 mm Pitch 2,54mm
- Connection: Mini USB. Driver: W98 / W2000 / W2003 / W2008 / WinXP / WinVista / W7 / W8 / Linux / Mac
Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards:
User manual for remote control + 4-channel receiver 315 MHz IC2262
- Wire the USB />

Allows control: - Up to 2 bidirectional current motors
- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features:
- Minimum operating voltage: 4.5 V
- Maximum operating voltage: 36 V
- Maximum current: ± 1.2 A
- Logic voltage: - 2.3V <= HIV <= VIN (high)
                        - 0.3V <= VIL <= 1.5V (low)
- Controller L293D
- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA
- D2, D4 - motorB

ESP32-S3-DevKitC-1-N8R8 general-purpose development board based on the ESP32-S3R8-WROOM-1 chip, Flash 8MB, PSRAM 8MB.

Mini ESP8266 ESP12E CH340 WiFi Development
NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features:

- Compatible with Arduino, programming with the Arduino IDE
- Power supply voltage: 5V
- LOGICAL LEVELS: 3.3V
- 11 input / output pins
- 1 ADC (input: 0-3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz - Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and power management units Integrated

NodeMcu module based on ESP8266 controller and programming in Lua language. 
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. 
It works as a standard WiFi 802.11 b / g / n 2.4 GHz. 
USB communication - the CP2102 chip. Characteristic of ESP 12E: 
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V), 
- Supported protocols: 802.11 b / g / n, 
- Network support: 2.4 GHz, 
- Band: 2400 (MHz), 
- Wi-Fi Direct (P2p), Soft Access Point, 
- TCP Stack / Integrated IP, 
- PLLs, Regulators and Integrated Power Management Units, 
- Output Power: 0.15 (W); + 19.5dBm in 802.11b mode,

The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on.

ESP32 processor development board with WiFi and Bluetooth (BLE) compatible with Arduino Uno shields. It is much faster than the ESP8266 processor (NodeMCU and the like) . Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth features:
Power: 5-12VDC WiFi 802.11 b / g / n / e / i (802.11n up to 150 Mbps) Bluetooth v4.2 BR / EDR and BLE. Compatible with Arduino Uno shields. 6 Analog input. 20 digital inputs / outputs (3.3V) (with PWM functions, interrupt). UART, SPI, I2C communication. Size: 68Ã — 53 mm Micro USB connection. 4Mbytes Flash Memory 520Kb Clock: 240Mhz (a core dedicated to WiFi processing) Temperature: -40C + 85C Current: 250mA (max) Current in saving mode: 0.15mA Operating current: 20mA (without WiFi) Useful links for Arduino / Raspberry programming and projects with Arduino /

Grove - Vision AI module with Himax HX6537-A processor, thumb-sized AI-powered OV2640 camera sensor, compatible with YOLO v5 and Edge Impulse.

SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables!

The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA.

WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins.

Classic development board designed and manufactured by Heltec Automation (TM), based on the ESP32-S3FN8 + SX1262. Integrates Wi-Fi, Bluetooth, lithium battery management system, dot matrix OLED screen, USB-C interface. Compatible with Arduino IDE, Micro Python, Platform.io, Espressif IDE. Our module is supplied with Lora antenna and IPEX adapter (U.FL) and header pins.