Logic Level Converter 3.3 / 5V I2C IIC 3.3V/5V I2C logic level converter module with soldering pins.Ideal to connect a device that works at 3.3V to one that works with 5V.It works with digital signals (high and low levels).Logic Level Converter 3.3 / 5V I2C IIC features:- Voltage: 3.3V/5V- Measures: 1.5x 1 cm Code C0004 Available Price €1.40
Male 40 Pin Header 1x40 Male 40 Pin Header 1x40 features: Type: Male, Insertion position: Vertical, Separation between pins: 2.54mm Code K0138 Available Price €0.57
Nano plate V3.0 CH340 + Arduino compatible pins It has an ATMega328P chip running at 16Mhz with a factory loaded bootloader Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per Pin I / O 40 mA - Flash Memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Clock Frequency: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0026 Available Price €8.26
Female Strip 40 Short Pins Female Strip 40 Short Pins features: - Pin spacing: 2.54mm - Insert position: Vertical - Insert: Pasante - Quantity: 1 unit of strips of 40 female pins each Code K0139 Available Price €0.57
Resistor 10K Ohm 5% 0,25W 1/4W Resistor 10K Ohm 5% 0,25W 1/4W features:-10K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0021 Available Price €0.07
Air Monitoring HAT for Raspberry Pi This HAT is an open source portable sensor that provides the level of suspended particulate matter quantity with its mass. It has a powerful and high-tech PMSA003 sensor that provides the information of suspended particulate matter (PM1.0, PM2.5, PM10) in the air per unit volume. Code RA127 ✗ Out-of-Stock Price €47.02
Trimpot potentiometer 3296W 1K Ohm kΩ linear Vertical variable PCB resistance from 1KΩ Linear. Code D0314 Available Price €0.35
Digital Light Intensity Sensor with Photo Resistance with LM393 Controller This photo-resistance module is very sensitive to ambient light. Activation of the microcontroller or retransmission modules,The brightness module of the ambient light reach the set threshold, the output is high when the ambient light exceeds the set threshold.The DO output can be connected directly to a microcontroller to detect the light environment and create a light control switch.It has a speed range of 0% to 100%. Digital Light Intensity Sensor with Photo Resistance with LM393 Controller features: - Operating voltage: 3.3 - 5 V- Input current: 50 mA- Use a very sensitive photo resistance- Use a LM393 wide voltage comparator, high quality output signal- Adjustable potentiometer can regulate the brightness of detected light Code M0156 Available Price €1.40
SparkFun WiFi Shield - ESP8266 The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on. Code SP006 Last items in stock Price €18.17
ESP-01 Esp-01 Esp8266 ESP01 WiFi USB Programmer Adaptor USB adapter that allows a direct USB connection to your ESP8266 ESP-01 or ESP-01S WiFi module. Based on the CH340 integrated circuit, which is a USB - Serial converter (UART). Code W0110 Available Price €2.60
Development Board Ra-02 LoRa SX1278 Ra-02 Module (433MHz) Long range NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0108 Available Price €7.43
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP039 Last items in stock Price €28.09
ESP32 Breakout Board Shield GPIO 30PIN Useful adapter for 30-pin esp32 modules (2x15 pins). Provides easy and secure connections. You can use the terminal block sockets or create connections via female pin header. Code W0127 ✗ Out-of-Stock Price €3.71
Shelly 1 Shelly 1 is a universal smarthome relay enabled to work with all the key smart home systems, including Google Home and Amazon Alexa, as well as an original Shelly solution Shelly Cloud Code WH001 ✗ Out-of-Stock Regular price €13.18 -€1.50 Price €11.68
ESP32 WROOM-32 DEVKIT V1 - Board with WiFi and Bluetooth WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins. Code W0103 Available Regular price €6.19 -€1.29 Price €4.90
SenseCAP K1100 - Sensor kit with LoRa and AI - "SenseCAP K1100 - The Sensor Prototype Kit with LoRa® and AI allows you to quickly digitise your world with LoRaWAN® and solve real-world challenges. With this plug-and-play toolkit, anyone can add artificial intelligence to their edge devices and unlock the potential of AIoT. Code SS049 Last items in stock Price €65.28
Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth ESP32 processor development board with WiFi and Bluetooth (BLE) compatible with Arduino Uno shields. It is much faster than the ESP8266 processor (NodeMCU and the like) . Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth features: Power: 5-12VDC WiFi 802.11 b / g / n / e / i (802.11n up to 150 Mbps) Bluetooth v4.2 BR / EDR and BLE. Compatible with Arduino Uno shields. 6 Analog input. 20 digital inputs / outputs (3.3V) (with PWM functions, interrupt). UART, SPI, I2C communication. Size: 68Ã — 53 mm Micro USB connection. 4Mbytes Flash Memory 520Kb Clock: 240Mhz (a core dedicated to WiFi processing) Temperature: -40C + 85C Current: 250mA (max) Current in saving mode: 0.15mA Operating current: 20mA (without WiFi) Useful links for Arduino / Raspberry programming and projects with Arduino / Code W0094 Last items in stock Price €8.22
ESP8266 ESP12E WiFi NodeMcu + Motor Drive L293D Expansion Shield Board Kit NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CP2102 chip. Characteristic of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V), - Supported protocols: 802.11 b / g / n, - Network support: 2.4 GHz, - Band: 2400 (MHz), - Wi-Fi Direct (P2p), Soft Access Point, - TCP Stack / Integrated IP, - PLLs, Regulators and Integrated Power Management Units, - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode, Code W0016 Available Price €6.98
SparkFun WiFi Shield - ESP8266 The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on. Code SP006 Last items in stock Price €18.17
ESP-01 Esp-01 Esp8266 ESP01 WiFi USB Programmer Adaptor USB adapter that allows a direct USB connection to your ESP8266 ESP-01 or ESP-01S WiFi module. Based on the CH340 integrated circuit, which is a USB - Serial converter (UART). Code W0110 Available Price €2.60
Development Board Ra-02 LoRa SX1278 Ra-02 Module (433MHz) Long range NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0108 Available Price €7.43
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP039 Last items in stock Price €28.09
ESP32 Breakout Board Shield GPIO 30PIN Useful adapter for 30-pin esp32 modules (2x15 pins). Provides easy and secure connections. You can use the terminal block sockets or create connections via female pin header. Code W0127 ✗ Out-of-Stock Price €3.71
Shelly 1 Shelly 1 is a universal smarthome relay enabled to work with all the key smart home systems, including Google Home and Amazon Alexa, as well as an original Shelly solution Shelly Cloud Code WH001 ✗ Out-of-Stock Regular price €13.18 -€1.50 Price €11.68
ESP32 WROOM-32 DEVKIT V1 - Board with WiFi and Bluetooth WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins. Code W0103 Available Regular price €6.19 -€1.29 Price €4.90
SenseCAP K1100 - Sensor kit with LoRa and AI - "SenseCAP K1100 - The Sensor Prototype Kit with LoRa® and AI allows you to quickly digitise your world with LoRaWAN® and solve real-world challenges. With this plug-and-play toolkit, anyone can add artificial intelligence to their edge devices and unlock the potential of AIoT. Code SS049 Last items in stock Price €65.28
Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth ESP32 processor development board with WiFi and Bluetooth (BLE) compatible with Arduino Uno shields. It is much faster than the ESP8266 processor (NodeMCU and the like) . Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth features: Power: 5-12VDC WiFi 802.11 b / g / n / e / i (802.11n up to 150 Mbps) Bluetooth v4.2 BR / EDR and BLE. Compatible with Arduino Uno shields. 6 Analog input. 20 digital inputs / outputs (3.3V) (with PWM functions, interrupt). UART, SPI, I2C communication. Size: 68Ã — 53 mm Micro USB connection. 4Mbytes Flash Memory 520Kb Clock: 240Mhz (a core dedicated to WiFi processing) Temperature: -40C + 85C Current: 250mA (max) Current in saving mode: 0.15mA Operating current: 20mA (without WiFi) Useful links for Arduino / Raspberry programming and projects with Arduino / Code W0094 Last items in stock Price €8.22
ESP8266 ESP12E WiFi NodeMcu + Motor Drive L293D Expansion Shield Board Kit NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CP2102 chip. Characteristic of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V), - Supported protocols: 802.11 b / g / n, - Network support: 2.4 GHz, - Band: 2400 (MHz), - Wi-Fi Direct (P2p), Soft Access Point, - TCP Stack / Integrated IP, - PLLs, Regulators and Integrated Power Management Units, - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode, Code W0016 Available Price €6.98