ESP8266 5V WiFi Relay Module AP Remote Control + STA You can easily control any device over the Internet through your phone, computer, etc. The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point). In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters). In STA mode, the relay module is connected to the access point (router) that supplies the network. Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers). You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off. Code W0067 Available Price €7.84
Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 0.5mm Tin ideal for application in consumer electronics circuitsWelding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 0.5mm features:- 100gr. 0,5mm diameter welding wire. 60% tin and 40% lead- Melting temperature 183 o C / 190 o C- Alloy Sn60 Pb40- Flux 2.5%- Quantity: 1 unit- High quality - manufactured in EU Code Q0005 ✗ Out-of-Stock Price €7.40
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.61
Aluminum Desoldering Pump Tin Antistatic Suction Desoldering iron for the removal of excess tin. You can quickly and effectively remove solder from a plate or circuit.Replaceable antistatic nozzle.Manufactured in Aluminum.Aluminum Desoldering Pump Tin Antistatic Suction features:- Length: 190mm- Desoldering pump- High suction power- Replaceable long-life silicone tip- Light weight- Easy use with one hand, light and resistant- Vacuum Solder Aluminum Desoldering Pump Solder Remover Pump Tool- A good quality product for fast and efficient removal of excess solder, ideal for PCB repair- High-capacity spring-loaded plunger quickly eliminates welding in one action. The Pumping tool easily- Disassemble for a quick clean Code H0001 Available Price €2.44
Resistor 1K Ohm 5% 0,25W 1/4W Resistor 1K Ohm 5% 0,25W 1/4W features:-1 unit - 1K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0076 Available Price €0.07
Speed controller for DC motor (PWM) 6V-28VDC 3A PWM 6V 12V 24V Speed controller for DC motor (PWM) 6V-28VDC 3A PWM 6V 12V 24V features: - Ideal to control the speed of DC motors - Input voltage: 6-28VDC - Max continuous output current: 3A - Max power: 100W - Dimensions: 50x17x28mm - PWM frequency: 21kHz - Adjustable duty cycle: 5% -100% - Keep in mind that the voltage applied to the motor will be the supply voltage applied to the circuit Code A0021 Available Price €4.87
40x Male to male cables 10cm 40x Male to male cables 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont male connectors on both ends - Compatible with 2.54mm female connectors - High quality and good working condition - Easy to install and use Code K0107 Available Price €1.64
Gel Battery 12V 7Ah Gel Battery 12V 7Ah features: Long service life - both in cyclic and buffer operation No delamination effect from the gelled electrolyte It tolerates high operating temperatures well It fully recovers to its original capacity from deep discharge Code PP104 ✗ Out-of-Stock Price €15.69
W1209 12V DC Thermostat Digital Temperature Controller Switch W1209 12V DC Thermostat Digital Temperature Controller Switch features: - Model: W1209 - Supply voltage: DC 12V - Temperature control mode: ON / OFF - Temperature range: -50 -110 ° C - Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C - Measurement accuracy: 0.1 ° C - Refresh rate: 0.5 s - Temperature protection 0-110 ° C - Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA - Power of output: 10A relay - Sensor probe: NTC waterproof sensor (10K 0.5%) - Environmental requirements: -10 ~ 60 ° C Humidity 20% -85% - Dimensions: 48 x 40 mm Code M0102 Available Price €3.13
BLE 4.0 UART Bluetooth Low Energy Module without Adapter This product is a Bluetooth module BLE 4.0 UART without adapter, low energy with serial transceiver.Logic level conversion circuit. No external level of 5V is needed to become a 3.3V level.The power input port is protected against the anti-circuit, to avoid the inverted accidental power plug, which leads to the module burnHM-10, Bluetooth module HM-11 series using IT chip CC2540 / 2541, configuration 256Kb space, supportIn commands.You can change the paper (master and slave mode) and the baud rate, the device name, the pairing of the password and other parameters, convenient and flexible. BLE 4.0 UART Bluetooth Low Energy Module without Adapter features: - Version AT-09 CC2541 Arduino Android IOS BLE- Serial transceiver Code W0087 Available Price €4.39
SONOFF NSPanel PRO Smart Scene Wall Switch - HMI panel NSPanel offers intelligent control of home appliances: lighting, thermostat, curtains, windows and wall switches. A colour touch screen with two buttons displays all the necessary information and allows you to conveniently navigate through the device's menu, making the Sonoff NSPanel the ideal control centre for your home. The NSPanel is designed to be mounted on the Sonoff switch frame (switch frame not included). Code WS079 Last items in stock Regular price €90.87 -€3.00 Price €87.87
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development Mini ESP8266 ESP12E CH340 WiFi Development NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC It works as a standard WiFi 802.11 b / g / n 2.4 GHz Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features: - Compatible with Arduino, programming with the Arduino IDE - Power supply voltage: 5V - LOGICAL LEVELS: 3.3V - 11 input / output pins - 1 ADC (input: 0-3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and power management units Integrated Code W0061 Available Price €2.88
Mini Dongle Adapter Bluetooth USB V2.0 Windows XP/VISTA/7 Work with Bluetooth compliant devices including notebook, PDA, digital camera,printer and mobile phone.Mini Dongle Adapter Bluetooth USB V2.0 Windows XP/VISTA/7 features:- Bluetooth specification V2.0 - Supporting profiles: networking, dial-up, fax, LAN access and handset - Operation system Windows98, 98se, Me, 2000, XP, Vista, Windows7 - Receiving/sending range: 100m Code W0093 Available Price €3.22
Relay Module DC 12V 10A 1 Channel Low/High Trigger Relay Module DC 12V 10A 1 Channel Low/High Trigger features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high) Code RL003 Available Price €1.89
Ethernet Shield W5100 Web Server Shield Ethernet for Arduino boards and compatible based on the Wiznet W5100 chip. Provides an easy way to connect your module to the local network now internet. Compatible with the official Arduino Ethernet library. With this shield you can build a web server. It can be used as a server or as a client. It has support for a microSD that can be used to store files for distribution on the network. Ethernet Shield W5100 Web Server features: - Controller: Wiznet W5100 - Supports protocols TCP and UDP - Supports up to 4 simultaneous connections - Compatible with all Arduino versions: UNO, mega 1280/2560 - Dimensions: 74 x 54 x 25mm Code W0007 ✗ Out-of-Stock Price €18.14
WiFi LoRa 32(V3) 863-928Mhz BLE5.0 OLED Classic development board designed and manufactured by Heltec Automation (TM), based on the ESP32-S3FN8 + SX1262. Integrates Wi-Fi, Bluetooth, lithium battery management system, dot matrix OLED screen, USB-C interface. Compatible with Arduino IDE, Micro Python, Platform.io, Espressif IDE. Our module is supplied with Lora antenna and IPEX adapter (U.FL) and header pins. Code W0128 Available Price €21.48
Traffic light LED red yellow green 5V display module Arduino Red, yellow and green LED traffic light mini kit ideal for educational and beginner Arduino projects. Code M0231 Available Price €1.98
8x8 LED Matrix Kit MAX7219 Arduino compatible PIC Dot Matrix Display Cascade DIY 8x8 LED Matrix Kit MAX7219 Arduino PIC Dot Matrix Display Cascade DIY features: - 8X8 LED matrix controlled by MAX7219 chip - 3mm red LED - SPI communication - Voltage: 4.7 - 5.3V DC - Interfaces to manage multiple modules in cascade - Matrix dimensions: 32mm x 32mm x 8mm - PCB dimensions: 32mm x 50mm Code M0062 Available Price €2.44
W1209 12V DC Thermostat Digital Temperature Controller Switch W1209 12V DC Thermostat Digital Temperature Controller Switch features: - Model: W1209 - Supply voltage: DC 12V - Temperature control mode: ON / OFF - Temperature range: -50 -110 ° C - Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C - Measurement accuracy: 0.1 ° C - Refresh rate: 0.5 s - Temperature protection 0-110 ° C - Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA - Power of output: 10A relay - Sensor probe: NTC waterproof sensor (10K 0.5%) - Environmental requirements: -10 ~ 60 ° C Humidity 20% -85% - Dimensions: 48 x 40 mm Code M0102 Available Price €3.13
BLE 4.0 UART Bluetooth Low Energy Module without Adapter This product is a Bluetooth module BLE 4.0 UART without adapter, low energy with serial transceiver.Logic level conversion circuit. No external level of 5V is needed to become a 3.3V level.The power input port is protected against the anti-circuit, to avoid the inverted accidental power plug, which leads to the module burnHM-10, Bluetooth module HM-11 series using IT chip CC2540 / 2541, configuration 256Kb space, supportIn commands.You can change the paper (master and slave mode) and the baud rate, the device name, the pairing of the password and other parameters, convenient and flexible. BLE 4.0 UART Bluetooth Low Energy Module without Adapter features: - Version AT-09 CC2541 Arduino Android IOS BLE- Serial transceiver Code W0087 Available Price €4.39
SONOFF NSPanel PRO Smart Scene Wall Switch - HMI panel NSPanel offers intelligent control of home appliances: lighting, thermostat, curtains, windows and wall switches. A colour touch screen with two buttons displays all the necessary information and allows you to conveniently navigate through the device's menu, making the Sonoff NSPanel the ideal control centre for your home. The NSPanel is designed to be mounted on the Sonoff switch frame (switch frame not included). Code WS079 Last items in stock Regular price €90.87 -€3.00 Price €87.87
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development Mini ESP8266 ESP12E CH340 WiFi Development NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC It works as a standard WiFi 802.11 b / g / n 2.4 GHz Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features: - Compatible with Arduino, programming with the Arduino IDE - Power supply voltage: 5V - LOGICAL LEVELS: 3.3V - 11 input / output pins - 1 ADC (input: 0-3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and power management units Integrated Code W0061 Available Price €2.88
Mini Dongle Adapter Bluetooth USB V2.0 Windows XP/VISTA/7 Work with Bluetooth compliant devices including notebook, PDA, digital camera,printer and mobile phone.Mini Dongle Adapter Bluetooth USB V2.0 Windows XP/VISTA/7 features:- Bluetooth specification V2.0 - Supporting profiles: networking, dial-up, fax, LAN access and handset - Operation system Windows98, 98se, Me, 2000, XP, Vista, Windows7 - Receiving/sending range: 100m Code W0093 Available Price €3.22
Relay Module DC 12V 10A 1 Channel Low/High Trigger Relay Module DC 12V 10A 1 Channel Low/High Trigger features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high) Code RL003 Available Price €1.89
Ethernet Shield W5100 Web Server Shield Ethernet for Arduino boards and compatible based on the Wiznet W5100 chip. Provides an easy way to connect your module to the local network now internet. Compatible with the official Arduino Ethernet library. With this shield you can build a web server. It can be used as a server or as a client. It has support for a microSD that can be used to store files for distribution on the network. Ethernet Shield W5100 Web Server features: - Controller: Wiznet W5100 - Supports protocols TCP and UDP - Supports up to 4 simultaneous connections - Compatible with all Arduino versions: UNO, mega 1280/2560 - Dimensions: 74 x 54 x 25mm Code W0007 ✗ Out-of-Stock Price €18.14
WiFi LoRa 32(V3) 863-928Mhz BLE5.0 OLED Classic development board designed and manufactured by Heltec Automation (TM), based on the ESP32-S3FN8 + SX1262. Integrates Wi-Fi, Bluetooth, lithium battery management system, dot matrix OLED screen, USB-C interface. Compatible with Arduino IDE, Micro Python, Platform.io, Espressif IDE. Our module is supplied with Lora antenna and IPEX adapter (U.FL) and header pins. Code W0128 Available Price €21.48
Traffic light LED red yellow green 5V display module Arduino Red, yellow and green LED traffic light mini kit ideal for educational and beginner Arduino projects. Code M0231 Available Price €1.98
8x8 LED Matrix Kit MAX7219 Arduino compatible PIC Dot Matrix Display Cascade DIY 8x8 LED Matrix Kit MAX7219 Arduino PIC Dot Matrix Display Cascade DIY features: - 8X8 LED matrix controlled by MAX7219 chip - 3mm red LED - SPI communication - Voltage: 4.7 - 5.3V DC - Interfaces to manage multiple modules in cascade - Matrix dimensions: 32mm x 32mm x 8mm - PCB dimensions: 32mm x 50mm Code M0062 Available Price €2.44