Plate STM32F103C8T6
  • Plate STM32F103C8T6
  • Plate STM32F103C8T6
  • Plate STM32F103C8T6
  • Plate STM32F103C8T6
  • Plate STM32F103C8T6

Plate STM32F103C8T6

B0010

The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel
We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit. The module is supplied in a soldered version.

OEM
5905323234000
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

Plate STM32F103C8T6 description

The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel
We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit

Plate STM32F103C8T6 features:



- ARM 32 Cortex-M3 CPU 72MHz chip
- STM32F103C8T6 microprocessor
- Operating voltage 2-3.6V
- Debug mode: Serial Wire Debug
- I / O Pins 37
- Flash 64KB
- SRAM 20 KB

Customers who bought this product also bought

Kapton type 10mm thermal tape

Characteristic: - Supports up to 280ºC
- Electrical and antistatic insulation
- Resistant to acid and alkaline products
- Resistant to solvent
- Adhesive
- Length Approx: 33m
- Polyamide adhesive tape 10mm 
- Known as Kapton polyamide tape
- Product for welding works on those that need to protect some component from the heat

I0061

Price €1.78

ESP8266 5V WiFi Relay Module AP Remote Control + STA

You can easily control any device over the Internet through your phone, computer, etc.
The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point).
In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters).
In STA mode, the relay module is connected to the access point (router) that supplies the network.
Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers).
You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off.

W0067

Price €7.84

Infrared LED Flame Sensor 5mm module

Led module infrared sensor for Arduino
Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nm
Particularly sensitive to the flame spectrum.
This optical flame sensor is a device that detects the existence of combustion by the light emitted by it.
Infrared LED Flame Sensor 5mm module features:
- 4 Pins Output:
    - A0: analog output
    - D0: digital output
    - GND: ground connection
    - VCC: 5V module power
- Range of light, Distance of 80 cm.
- Angle detection of about 60 degrees,
- This light can be detected by an optical sensor,
- Can be captured by digital inputs and analog inputs of Arduino.

S0133

Price €1.15

HB100 Microwave Doppler Radar Motion Sensor

Microwave motion detector module.
The main applications may be security alarms and sensors, systems Automatic doors, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and control applications.
High resistance to radio frequency interference.
Characteristic:
- Frequency: 10.525GHz
- Frequency Accuracy: 3MHz
- Minimum Output: 13dBm EIRP
- Operating Voltage: 5V ± 0.25V
- Operating current (CW): 60mA maximum, 37mA typical
- Harmonic emissions: -10dBm
- Detection Range: Over 20 meters
- Power of Output: 5mW
The device is sensitive to electrostatic discharge and can be damaged during welding.
The IF output is particularly sensitive.

M0026

Price €4.50

Relay Module DC 5V 10A 2 Channel Low/High Trigger

Relay Module DC 5V 10A 2 Channel Low/High Trigger features:
- Channels: 2 (independent protected with Optocouplers)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator: For each channel
- Dimensions: 40x 50mm
- It has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

RL002

Price €2.60

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32

P0008

Price €1.15
€9.01

9,01 tax excl.

1
Last item
Price €9.01

Order until 4pm we will send today
30 days return