DS18B20 Temperature Sensor 0.5ºC TO-92

Led infrared sensor.
Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nm
Particularly sensitive to the flame spectrum.
This optical flame sensor is a device that detects the existence of combustion by the light emitted by it.
Infrared LED Flame Sensor 5mm features:
- Range of light, Distance of 80 cm.
- Angle detection of about 60 degrees,
- This light can be detected by an optical sensor,
- Can be captured by digital inputs and analog inputs of Arduino.

The GY-906 BCC is a plate-mounted temperature sensor, based on an integrated 3 V infrared thermometer, single zone, medical precision, compensated gradient, accuracy within 5 cm is approximately 0.5 degrees higher

NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance.   Thermistor NTC 1.0K 5% MF52A epoxy resin coating resistor features:

Size: 3mm
Rated resistance: R25 = 1.0k
B value 25/85 = 3950°K
Rated power: ‰¤ 50mW
Tolerance:± 5%
Operating temperature: from -40°C to +125°C  Tinned steel wire 25mm

The SNZB-02D sensor will monitor temperature and humidity in real time remotely in the application or on the display, with a range of up to 120 metres. The sensor has a built-in intelligent Swiss hygrometer sensor that provides more precise readings, maintaining an accuracy of ±0.2°C/±0.4°F in temperature and ±2% relative humidity in humidity, updating the readings every 5 seconds.

Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 100 cm.
DS18B20 Submersible Probe Sensor Temperature features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 °C to 125 °C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
      - Red Vcc
      - Yellow digital output
- Inocidable steel
- Cable length: 1m

Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 10m. DS18B20 Digital Temperature Sensor Probe 10m features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 °C to 125 °C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
      - Vcc red
      - Yellow digital output
- Inocidable steel
- Cable length: 10m

Encapsulated with water resistant stainless steel with sensor dimensions 5.5*50mm, cable length 200 cm. DS18B20 Probe 2m Submersible Temperature Sensor features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 °C to 125 °C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
      - Vcc red
      - Yellow digital output
- Inocidable steel
- Cable length: 2m  

LM35 Temperature Sensor LM35DZ TO92 features:
- The output is linear and each degree Celsius equals 10 mV
- Power supply from 4 to 30 Vdc
- Connection through analog input
- Temperature range from 0ºC to 100ºC
- Linearity +10 mV / ºC
- Quantity: 1 unit

Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 5m. DS18B20 Digital Temperature Sensor Probe 5m features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 °C to 125 °C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
      - Vcc red
      - Yellow digital output
- Inocidable steel
- Cable length: 5m

Precision Temperature Sensor TO-92 LM335 LM335Z-ST features:
- Power supply from 5 to 30 Vdc
- Connection through analog input
- Temperature range from -40ºC to 100ºC
- Linearity +10 mV / ºK
- Accuracy of measurement: ± 2 ° C
- Manufacturer: Texas Instruments