5.8GHz Doppler Radar Motion Sensor

The optical module sensor (reflective) with comparator LM393, which detects obstacles with high precision.
The ideal obstacle detection detector for the installation of smart robots.
TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of a object using infrared reflection on the object.
The working wavelength is 950nm.
The transmitter is infrared LED and the phototransistor receiver.
By using LM393 comparator the module has a binary output (D0) that is at level 1 (object is detected).
The sensor allows the detection of an object at a distance of up to 12 mm.

It is very easy to make it work with an Arduino, PIC or any other microcontroller.
In its output pin we can measure the pulse width PWM depending on the distance of the obstacle.
Mounting bracket is ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. HC-SR04 + Ultrasonic Sensor Support Arduino features:
- Supply voltage: 5V (4.5V-6V)
- Consumption: typical 30 mA, (35 mA max)
- Interface: VCC, GND, Signal
- Range: 2 cm to 3 meters
- Angle 15º
- LED measurement indicator in progress
- Frequency: 40 kHz for 200 μs
- Size: 30 mm x 20 mm Feature of the support: - Material: Acrylic
- Transparent color
- Includes screws

Ideal for projects with ARDUINO, Smart Car. Sensor Module Infrared Obstacle Detector Car Robot features:
- Power supply: 3.3 - 5V DC
- OUT level 0/1 output
- Sensitivity adjustment
- Power LED
- Distance from detection: 2 - 30cm (max60cm)
- detection angle: 35º
- LED output status indicator
- Dimensions: 40x13x8mm

Photoelectric sensor standard, reliable assurance of 1 million units per year.

· Industry's top class built-in amplifier

· Guaranteed low-temperature operation that can be used in freezing warehouse

· Improvement of coincidence between optical and mechanical axis.

· Protection of sensor even if wiring mistake occurs output reverse protection function is carried (we add diode for reverse connection protection to output line).

Characteristic: - Supply voltage: 4.5V- 5.5V
- Consumption: 30 mA typical
- Analog output
- Range: 10cm to 80cm
- Dimensions: 29x12mm
- Cable length: 20cm GP2Y0A21YK0F Sharp Analog IR distance sensor 10CM-80CM Arduino

Ultrasonic sensors overcome many of the weaknesses of IR sensors by providing distance measurement regardless of the color and illumination of obstacles. Ultrasound Distance Sensor HC-SR05 features:
- Power supply: 4.5-5.5 VDC
- Supply current: 10 to 40 mA
- Activation pin format: 10 μs digital pulse
- Echo Pin Output: 0-Vcc
- Echo Pin Format: the output is DIGITAL and directly proportional with range. See our conversion formula below
- Measurement range: 2cm to ~ 4.5m
- Measurement resolution: 0.3cm
- Measurement angle: up to 15 degrees
- Measurement speed: 40 Hz,
- Connector: standard 5-pin male connector that can be connected directly to boards or breadboards:
- 1: VCC
- 2: Trig
- 3: Echo

Ideal for projects with ARDUINO, Smart Car
Detects transparent and translucent obstacles
E18-D80NK Infrared Obstacle Avoidance Sensor Module 3-80cm Smart Car features:
- Current consumption: up to 100 mA
- Supply voltage 5V
- Current consumption <25mA
- Response time of 2 ms
- Measured distance: 3-80cm 15st angle
- Screw to adjust the sensitivity, the back
- Output status led indicator
- Operating temperature: -25°C - + 55°C
- Material: high-strength plastic
- Type of output: normally open, NPN
- Dimensions: 18 mm in diameter, Length 45 mm
- Cable length 55cm
- Departures:
      - Brown: +
      - Blue: -
      - Black: OUT

The optical (reflective) module sensor with LM393 comparator, which detects obstacles with high accuracy. The ideal detector for obstacle detection for the installation of intelligent robots.TCRT5000: reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of an object using infrared reflection on the object. The transmitter is an infrared LED and the receiver is a phototransistor. The sensor allows the detection of an object at a distance of up to 3.5 cm from the white paper and 1 cm from the person's finger.

Holder for ultrasonic, distance meter HC-SR04. Ideal for installing the sensor on mobile platforms such as robots, vehicles, etc.

It is very easy to make it work with an Arduino, PIC or any other microcontroller.
In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle.
HC-SR04 Ultrasonic Sensor Distance Measuring Module features:
- Supply voltage: 5V (4.5V- 6V)
- Consumption: 30 mA typical, (35 mA max)
- Interface: VCC , GND, Signal
- Range: 2 cm to 3 meters
- Angle 15º
- LED indicator of measurement in progress
- Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm
- Quantity: 1 unit
Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry:
Automatic robot operation with obstacle detection />