AG Gold thermal grease 3g syringe AG Gold is a high quality thermal conductive paste. Due to its gold content, its thermal conductivity is 3 times higher than in the case of normal pasta.This allows the processor to lower the processor temperature by approximately 6 degrees, even without changing the radiator. Pasta is the best alternative for overlockers.Thermal conductivity:> 2.8 W / mK, Code Q0090 Available Price €4.25
Time Switch Module 12V NE555 Monostable Switch Delayed This module is a timed switch that allows you to program several types of applications such as lights. Time Switch Module 12V NE555 Monostable Switch Delayed features: Code M0160 Available Regular price €4.59 -€0.59 Price €4.00
Potentiometer B1K Linear Potentiometer B1K Linear features: -1k OHM kΩ - linear potentiometer 1k Arduino -Tolerance: +/- 20% - Power: 0.125W Code K0065 Available Price €0.99
Red Laser Diode Module 650nm 5mW 6mm 5V lL2N4 This module adapted for the arduino includes a laser diode and a 3-pin connector for a simple and quick adaptation with the Arduino. The diode is mainly used for laser toys, all kinds of level meter, instruments, stylus pen, mini LCD projector, remote listeners laser, alarm anti-theft light remote control. Light shots and different display can make the color of the image element a little different from the real object. The measurement allowed error is +/- 1-3 cm. Characteristic: - Supply voltage: 5VDC - Connector of 3 pins: 1- GND 2- VCC 3- Light control of the laser diode - Point mode: point facula - Continuous output - Operating temperature: -36 ° C - + 65 ° C - Laser wavelength: 650nm (red) Code M0077 Available Price €1.49
40x Male to male cables 20cm Characteristic: -Length: 20cm -Quantity: 40 cables -Mono Dupont connectors on both ends -Compatible with 2.54mm female connectors -High quality and good working condition -Easy to install and use Code K0006 Available Price €2.49
Module Relay 5V Light sensor LDR photoresistor This module is a three way switch ( COM, NO and NC ) that uses the intensity of the ambient light to control directly the load at the output. Its adjustment potentiometer allows changing the sensitivity and setting the start threshold of the relay. The relay is energized when it is darker than the threshold. Code RL016 Available Price €2.39
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.95
Power Adapter 220VAC DC 5.1V, 3A USB-C Power Adapter 220VAC DC 5.1V, 3A USB-C features: - Input voltage: 100 ~ 240V AC 50Hz- Output voltage: 5.1V DC- Output current: 3A- DC connector: USB-C- Cable length 80cm Code RA063 Available Price €8.85
GP2Y0A21YK0F Strong Infrared IR Distance Meter Characteristic: - Supply voltage: 4.5V- 5.5V - Consumption: 30 mA typical - Analog output - Range: 10cm to 80cm - Dimensions: 29x12mm - Cable length: 20cm GP2Y0A21YK0F Sharp Analog IR distance sensor 10CM-80CM Arduino Code S0024 Available Price €9.95
Holder for HC-SR04 Ultrasonic Sensor Holder for ultrasonic, distance meter HC-SR04. Ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. Code S0137 Available Price €0.99
HC-SR04 + Ultrasonic Sensor Support for Arduino compatible sensors It is very easy to make it work with an Arduino, PIC or any other microcontroller.In its output pin we can measure the pulse width PWM depending on the distance of the obstacle.Mounting bracket is ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. HC-SR04 + Ultrasonic Sensor Support Arduino features: - Supply voltage: 5V (4.5V-6V)- Consumption: typical 30 mA, (35 mA max)- Interface: VCC, GND, Signal- Range: 2 cm to 3 meters- Angle 15º- LED measurement indicator in progress- Frequency: 40 kHz for 200 μs- Size: 30 mm x 20 mm Feature of the support: - Material: Acrylic- Transparent color- Includes screws Code S0006 Available Regular price €3.24 -€0.60 Price €2.64
TCRT5000 Module 3.5cm IR infrared sensor The optical (reflective) module sensor with LM393 comparator, which detects obstacles with high accuracy. The ideal detector for obstacle detection for the installation of intelligent robots.TCRT5000: reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of an object using infrared reflection on the object. The transmitter is an infrared LED and the receiver is a phototransistor. The sensor allows the detection of an object at a distance of up to 3.5 cm from the white paper and 1 cm from the person's finger. Code S0138 Available Price €1.69
TCRT5000 IR Infrared Sensor Module The optical module (reflective) sensor with CMOS Schmitt inverter 74HC14D, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of an object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver. The sensor allows the detection of an object at a distance of up to 15 mm. TCRT5000 IR Infrared Sensor Module features: - The module has an output: digital - CMOS Schmitt inverter 74HC14D - Power supply: 5V - Range: 0.2 mm - 15 mm Code S0048 Available Price €1.49
Module TCRT5000 Infrared Sensor IR Tracker Line Obstacle The optical module sensor (reflective) with comparator LM393, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of a object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver. By using LM393 comparator the module has a binary output (D0) that is at level 1 (object is detected). The sensor allows the detection of an object at a distance of up to 12 mm. Code S0025 Available Price €1.85
HC-SR04 Ultrasonic Sensor Distance Measuring Module It is very easy to make it work with an Arduino, PIC or any other microcontroller. In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle. HC-SR04 Ultrasonic Sensor Distance Measuring Module features: - Supply voltage: 5V (4.5V- 6V) - Consumption: 30 mA typical, (35 mA max) - Interface: VCC , GND, Signal - Range: 2 cm to 3 meters - Angle 15º - LED indicator of measurement in progress - Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm - Quantity: 1 unit Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry: Automatic robot operation with obstacle detection /> Code S0007 Available Price €1.79
Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor features: - Operating range: 0.2mm to 15mm - Receiver: Phototransistor - Emitter: Infrared Led - Wavelength: 950 nm Code S0026 Available Price €0.50
5.8GHz Doppler Radar Motion Sensor 5.8GHz Doppler Radar Motion Sensor features: - Microwave motion detector module - The main applications can be security alarms and sensors, Automatic door systems, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and monitoring applications. - High resistance to radio-frequency interference - Frequency: 5.8GHz - Operating Voltage: 3.3V - 20V TTL 3.3V - Standby Current: 3mA - Detection Range: 3-8 meters, 360 degrees - Power of Output: 2mW - Dimensions: 32x23 mm - R6 - time-delay; initial value 2.2k - 1s, without delay resistance 30s, can be adjusted up to 250k - R9 - for sensitivity adjustment Code M0112 ✗ Out-of-Stock Price €4.46
HB100 Microwave Doppler Radar Motion Sensor Microwave motion detector module. The main applications may be security alarms and sensors, systems Automatic doors, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and control applications. High resistance to radio frequency interference. Characteristic: - Frequency: 10.525GHz - Frequency Accuracy: 3MHz - Minimum Output: 13dBm EIRP - Operating Voltage: 5V ± 0.25V - Operating current (CW): 60mA maximum, 37mA typical - Harmonic emissions: -10dBm - Detection Range: Over 20 meters - Power of Output: 5mW The device is sensitive to electrostatic discharge and can be damaged during welding. The IF output is particularly sensitive. Code M0026 Available Price €5.44
GP2Y0A21YK0F Strong Infrared IR Distance Meter Characteristic: - Supply voltage: 4.5V- 5.5V - Consumption: 30 mA typical - Analog output - Range: 10cm to 80cm - Dimensions: 29x12mm - Cable length: 20cm GP2Y0A21YK0F Sharp Analog IR distance sensor 10CM-80CM Arduino Code S0024 Available Price €9.95
Holder for HC-SR04 Ultrasonic Sensor Holder for ultrasonic, distance meter HC-SR04. Ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. Code S0137 Available Price €0.99
HC-SR04 + Ultrasonic Sensor Support for Arduino compatible sensors It is very easy to make it work with an Arduino, PIC or any other microcontroller.In its output pin we can measure the pulse width PWM depending on the distance of the obstacle.Mounting bracket is ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. HC-SR04 + Ultrasonic Sensor Support Arduino features: - Supply voltage: 5V (4.5V-6V)- Consumption: typical 30 mA, (35 mA max)- Interface: VCC, GND, Signal- Range: 2 cm to 3 meters- Angle 15º- LED measurement indicator in progress- Frequency: 40 kHz for 200 μs- Size: 30 mm x 20 mm Feature of the support: - Material: Acrylic- Transparent color- Includes screws Code S0006 Available Regular price €3.24 -€0.60 Price €2.64
TCRT5000 Module 3.5cm IR infrared sensor The optical (reflective) module sensor with LM393 comparator, which detects obstacles with high accuracy. The ideal detector for obstacle detection for the installation of intelligent robots.TCRT5000: reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of an object using infrared reflection on the object. The transmitter is an infrared LED and the receiver is a phototransistor. The sensor allows the detection of an object at a distance of up to 3.5 cm from the white paper and 1 cm from the person's finger. Code S0138 Available Price €1.69
TCRT5000 IR Infrared Sensor Module The optical module (reflective) sensor with CMOS Schmitt inverter 74HC14D, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of an object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver. The sensor allows the detection of an object at a distance of up to 15 mm. TCRT5000 IR Infrared Sensor Module features: - The module has an output: digital - CMOS Schmitt inverter 74HC14D - Power supply: 5V - Range: 0.2 mm - 15 mm Code S0048 Available Price €1.49
Module TCRT5000 Infrared Sensor IR Tracker Line Obstacle The optical module sensor (reflective) with comparator LM393, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of a object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver. By using LM393 comparator the module has a binary output (D0) that is at level 1 (object is detected). The sensor allows the detection of an object at a distance of up to 12 mm. Code S0025 Available Price €1.85
HC-SR04 Ultrasonic Sensor Distance Measuring Module It is very easy to make it work with an Arduino, PIC or any other microcontroller. In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle. HC-SR04 Ultrasonic Sensor Distance Measuring Module features: - Supply voltage: 5V (4.5V- 6V) - Consumption: 30 mA typical, (35 mA max) - Interface: VCC , GND, Signal - Range: 2 cm to 3 meters - Angle 15º - LED indicator of measurement in progress - Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm - Quantity: 1 unit Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry: Automatic robot operation with obstacle detection /> Code S0007 Available Price €1.79
Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor features: - Operating range: 0.2mm to 15mm - Receiver: Phototransistor - Emitter: Infrared Led - Wavelength: 950 nm Code S0026 Available Price €0.50
5.8GHz Doppler Radar Motion Sensor 5.8GHz Doppler Radar Motion Sensor features: - Microwave motion detector module - The main applications can be security alarms and sensors, Automatic door systems, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and monitoring applications. - High resistance to radio-frequency interference - Frequency: 5.8GHz - Operating Voltage: 3.3V - 20V TTL 3.3V - Standby Current: 3mA - Detection Range: 3-8 meters, 360 degrees - Power of Output: 2mW - Dimensions: 32x23 mm - R6 - time-delay; initial value 2.2k - 1s, without delay resistance 30s, can be adjusted up to 250k - R9 - for sensitivity adjustment Code M0112 ✗ Out-of-Stock Price €4.46
HB100 Microwave Doppler Radar Motion Sensor Microwave motion detector module. The main applications may be security alarms and sensors, systems Automatic doors, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and control applications. High resistance to radio frequency interference. Characteristic: - Frequency: 10.525GHz - Frequency Accuracy: 3MHz - Minimum Output: 13dBm EIRP - Operating Voltage: 5V ± 0.25V - Operating current (CW): 60mA maximum, 37mA typical - Harmonic emissions: -10dBm - Detection Range: Over 20 meters - Power of Output: 5mW The device is sensitive to electrostatic discharge and can be damaged during welding. The IF output is particularly sensitive. Code M0026 Available Price €5.44