DHT22/AM2302 Temperature Humidity Sensor

The solar power management module is designed for 6V~24V solar panel. It can charge Li 3.7V battery through solar panel or USB connection, and provides 5V/1A regulated output.

The module has two outputs: analog A0 and digital D0
Digital output D0 - signal 0 appears or 1 depending on the threshold setting
The threshold is set with the potentiometer
The sensor can be used for example:
Automatic watering for potted plants
With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants
Characteristic:
Operation: 3.3V -5V
- Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - indicator digital switching output
- PCB measurements: 3 x 1.5 cm
- Probe measurements: 6 x 3 cm

The local Zigbee gateway for your Tuya Zigbee devices provides high-speed local Ethernet + Zigbee Mesh connectivity, increased automation possibilities, local memory for parameters and devices.

The SparkFun micro:Climate kit is a complete weather station kit that builds on the weather:bit carrier board with weather and soil moisture sensors, all powered by the micro:bit. board.

- The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values ​​and measures tenths of a degree
Characteristic:
- Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy
- Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy
- Maximum sampling rate: 2 seconds
Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards:
Write texts on the OLED 0.96 '' screen
- Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen
Send />

The humidity sensor DHT11 comes in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. DHT11 Temperature and Humidity Sensor features:
- Operating voltage: 3 to 5 VDC
- Humidity measurement range: 20-95% ± 5% accuracy
- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy
- Maximum sampling rate: 2 seconds
- Working current 2.5mA
- Iterfaz 1-wire
- Dimensions: 2.3 x1.2x 0.5cm
- Quantity: 1 unit

The BME280 is an environmental sensor (SEN0236) integrating a temperature sensor, a humidity sensor and a barometer. Powered from 3.3 V to 5 V with I2C and SPI interface. Measuring range: temperature: -40 °C to 85 °C, humidity: 0 %RH to 100 %RH, pressure: 300 hPa to 1100 hPa.

The SNZB-02D sensor will monitor temperature and humidity in real time remotely in the application or on the display, with a range of up to 120 metres. The sensor has a built-in intelligent Swiss hygrometer sensor that provides more precise readings, maintaining an accuracy of ±0.2°C/±0.4°F in temperature and ±2% relative humidity in humidity, updating the readings every 5 seconds.

The solar power management module with the CN3065 chip is ideal for IoT (Internet of Things) projects with renewable energy. Compared to the previous version of the module, improvements have been made to the energy management of the connected battery.

The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement.
Characteristic:
- Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy
- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy
- Maximum sampling rate: 2 seconds - Working current 2.5mA
- 1-wire interface
- Dimensions: 32 x14 mm
- Quantity: 1 unit with 3x female / female cables