Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM This module, which uses the exclusive L298P chip for driving high-power motors, can directly control two DC motors, with a drive current up to 2A. The motor output uses eight-speed Schottky diodes as protection.The design of the letter allows you to connect directly to the Arduino UNO R3 for easier use. Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM features: - 1 logical step of the input voltage VD: 5 VDC- Control of the input voltage VS and control by pulse width modulation: - VIN input: 6 - 12 VDC - PWRIN input: 4.8 - 35 VDC- Logic current flow: Iss <36m A- Operation current management: Io <2 A- Maximum power dissipation 25W (T = 75 ° C)- Input of the control signal: Code M0136 Available Regular price €11.50 -€1.51 Price €9.99
Shield for Arduino Mega2560 Prototype PCB shield board with screw terminal block for Arduino. A very convenient solution for first experiments with Arduino Mega board. To assemble your projects in a comfortable and tidy way, access to all Arduino Mega2560 pins, universal board area, 5V and Gnd buses, reset button. Shield is supplied assembled. Code B0151 Available Regular price €11.95 -€1.00 Price €10.95
Arduino NICLA Vision Nicla Vision combines a powerful STM32H747AII6 Dual ARM® Cortex® M7/M4 IC processor with a TinyML-enabled 2 MP colour camera, as well as a smart 6-axis motion sensor, integrated microphone and distance sensor. Supports MicroPython, and offers WiFi and Bluetooth® Low Energy connectivity. Code ABX00051 Last items in stock Price €120.99
Arduino NICLA Sense ME Nicla Sense ME is the smallest Arduino-developed board equipped with a range of the latest Bosch environmental and motion sensors. The module is based on the nRF52832 ARM Cortex M4 chip clocked at 64 MHz with 512 kB of Flash, 64 kB of RAM and 2 MB of SPI Flash and 2 MB of QSPI embedded memory. The Nicla Sense ME features the Bosch BHI260AP, BMP390, BMM150 and BME688 embedded sensors. Code ABX00050 Last items in stock Price €95.59
MyoWare Power Shield MyoWare Power Shield is designed to use two standard CR2032 coin cell batteries to power the MyoWare muscle sensor. These will be connected in parallel for extended capacity at a nominal 3.0V. Code SP071 Backorder Price €6.49
SparkFun Ardumoto - Motor Driver Shield The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased. Code SP011 Available Price €23.99
Nano V3.0 Terminal Block Adapter Nano V3.0 Terminal Block Adapter features: - Nano V3.0 Atmega328P adapter with soldered connectors - PCB dimensions: 53mm x 35mm Code B0024 Available Price €4.49
Arduino Multifunction shield - Display, LEDs, pushbuttons, buzzer Getting started with Arduino? This multi-function shield for Arduino UNO is ideal for your first Arduino DIY projects. It includes 4 7-segment displays, buzzer, 3 push buttons, 4 LEDs, potentiometer and sockets. Code M0230 Available Price €4.89
USB Host Shield Google Android ADK UNO Mega 2560 USB Host Shield Google Android ADK UNO Mega 2560 features: Shield ADK USB allows: - Communication with other USB devices, to build their own mobile accessories- Create projects that require USB Host functionality- Supports USB 2.0, Android ADK- It can also be used with any device equipped with SPI interface- Compatible with Android devices: v2.3.4 and above- USB Host with support for HUB protocol Code M0005 Last items in stock Price €19.50
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €7.90
SparkFun Biomedical sensor pad set 10pcs This a pack of 10 disposable electrodes is for biomedical measuring including EEG. Best suited for monitoring of neuro- and bio-feedback purposes. These are a single use, however very user friendly thanks to the latex-free gel. This is not a medical device and is to be used for strictly educational purposes. Code SP029 Available Price €12.95
Sensor Cable - Electrode Pads (3 connector) This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads. Code SP075 Available Price €8.99
MyoWare 2.0 Muscle Sensor Basic Kit Sparkfun sensor MyoWare® 2.0 from Advancer Technologies is a newer version of this producer's bestseller. The MyoWare 2.0 muscle sensor included in this kit has been redesigned from the ground up with a new compact and easy-to-use design, and has been updated with the latest, most advanced chipset to improve sensor performance and reliability. In addition, MyoWare has developed a range of shields that work with the sensor (in our LED shield offering, displaying sensor readings as LED lights). Code SP044 Available Price €121.95
MyoWare 2.0 Muscle Sensor Development Kit Sparkfun MyoWare 2.0 Muscle Sensor Development Kit is an all-in-one electromyography (EMG) sensor kit compatible with Arduino. Just snap on a MyoWare 2.0 Shield, add some EMG sensor pads, connect the sensor to a muscle group and flex! The kit also includes the SparkFun RedBoard Plus is an Arduino compatible board and the MyoWare 2.0 Arduino Shield to connect the MyoWare® 2.0 sensor via a cable to the Arduino. Code SP046 Last items in stock Price €182.95
Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM This module, which uses the exclusive L298P chip for driving high-power motors, can directly control two DC motors, with a drive current up to 2A. The motor output uses eight-speed Schottky diodes as protection.The design of the letter allows you to connect directly to the Arduino UNO R3 for easier use. Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM features: - 1 logical step of the input voltage VD: 5 VDC- Control of the input voltage VS and control by pulse width modulation: - VIN input: 6 - 12 VDC - PWRIN input: 4.8 - 35 VDC- Logic current flow: Iss <36m A- Operation current management: Io <2 A- Maximum power dissipation 25W (T = 75 ° C)- Input of the control signal: Code M0136 Available Regular price €11.50 -€1.51 Price €9.99
Shield for Arduino Mega2560 Prototype PCB shield board with screw terminal block for Arduino. A very convenient solution for first experiments with Arduino Mega board. To assemble your projects in a comfortable and tidy way, access to all Arduino Mega2560 pins, universal board area, 5V and Gnd buses, reset button. Shield is supplied assembled. Code B0151 Available Regular price €11.95 -€1.00 Price €10.95
Arduino NICLA Vision Nicla Vision combines a powerful STM32H747AII6 Dual ARM® Cortex® M7/M4 IC processor with a TinyML-enabled 2 MP colour camera, as well as a smart 6-axis motion sensor, integrated microphone and distance sensor. Supports MicroPython, and offers WiFi and Bluetooth® Low Energy connectivity. Code ABX00051 Last items in stock Price €120.99
Arduino NICLA Sense ME Nicla Sense ME is the smallest Arduino-developed board equipped with a range of the latest Bosch environmental and motion sensors. The module is based on the nRF52832 ARM Cortex M4 chip clocked at 64 MHz with 512 kB of Flash, 64 kB of RAM and 2 MB of SPI Flash and 2 MB of QSPI embedded memory. The Nicla Sense ME features the Bosch BHI260AP, BMP390, BMM150 and BME688 embedded sensors. Code ABX00050 Last items in stock Price €95.59
MyoWare Power Shield MyoWare Power Shield is designed to use two standard CR2032 coin cell batteries to power the MyoWare muscle sensor. These will be connected in parallel for extended capacity at a nominal 3.0V. Code SP071 Backorder Price €6.49
SparkFun Ardumoto - Motor Driver Shield The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased. Code SP011 Available Price €23.99
Nano V3.0 Terminal Block Adapter Nano V3.0 Terminal Block Adapter features: - Nano V3.0 Atmega328P adapter with soldered connectors - PCB dimensions: 53mm x 35mm Code B0024 Available Price €4.49
Arduino Multifunction shield - Display, LEDs, pushbuttons, buzzer Getting started with Arduino? This multi-function shield for Arduino UNO is ideal for your first Arduino DIY projects. It includes 4 7-segment displays, buzzer, 3 push buttons, 4 LEDs, potentiometer and sockets. Code M0230 Available Price €4.89
USB Host Shield Google Android ADK UNO Mega 2560 USB Host Shield Google Android ADK UNO Mega 2560 features: Shield ADK USB allows: - Communication with other USB devices, to build their own mobile accessories- Create projects that require USB Host functionality- Supports USB 2.0, Android ADK- It can also be used with any device equipped with SPI interface- Compatible with Android devices: v2.3.4 and above- USB Host with support for HUB protocol Code M0005 Last items in stock Price €19.50
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €7.90