Connectors 20x BLS02 Female/Female 2 Pins RoHS Single Row Connectors 20x BLS02 Female/Female 2 Pins RoHS Single Row features: - Step between pins: 2.54 mm- Manufacturer: Maritex- Number of connections: 2 in a single row- Type: female / female- RoHS standard Code K0118 Available Price €0.09
Ceramic Capacitor 10nF 50v 103 Ceramic Capacitor 10nF 50v 103 PCB PIC Arduino 0.01uF features: Orders only in multiples of 20 units-Type: Ceramic Y5V-Tolerance: +/-20%-Dimensions: diameter 6mm, pitch 5.08mm Code D0053 Available Price €0.06
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 Backorder Price €4.49
DS18B20 Probe 2m Submersible Temperature Sensor Encapsulated with water resistant stainless steel with sensor dimensions 5.5*50mm, cable length 200 cm. DS18B20 Probe 2m Submersible Temperature Sensor features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 2m Code S0015 Available Price €3.79
Connectors 15x BLS03 Female/Female 3 Pins RoHS Single Row Connectors 15x BLS03 Female/Female 3 Pins RoHS Single Row features: - Step between pins: 2.54 mm- Manufacturer: Maritex- Number of connections: 3 in a single row- Type: Female / Female- RoHS standard Code K0119 Available Price €0.10
Resistor 4,7M Ohm 5% 0,25W 1/4W Resistor 4,7M Ohm 5% 0,25W 1/4W features:-4.7M Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0033 Available Price €0.08
T-Cobbler Protoboard Extension Plate GPIO 40 Raspberry PI B+ Pin T-Cobbler Protoboard Extension Plate GPIO 40 Raspberry PI B+ Pin features: - Shield expansion module for Raspberry Pi 2 and Pi 3, B and B + - Dimension: 6 x 7.3x 1.9mm Code RA04 Available Price €2.99
Transparent Acrylic Box R3 for Arduino Uno Protection box for Arduino UNO R3 made of high quality acrylic material. Arduino Uno Transparent Acrylic Box R3 features: - Compatible with Arduino UNO - Material: transparent acrylic - External dimensions: 80x 65x 18.5mm Code B0013 Available Price €1.95
Solar Power Management Module, for 6V~24V Solar Panel The solar power management module is designed for 6V~24V solar panel. It can charge Li 3.7V battery through solar panel or USB connection, and provides 5V/1A regulated output. Code WV002 Available Price €12.95
Sensor Module Moisture Earth Water Soil The module has two outputs: analog A0 and digital D0 Digital output D0 - signal 0 appears or 1 depending on the threshold setting The threshold is set with the potentiometer The sensor can be used for example: Automatic watering for potted plants With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants Characteristic: Operation: 3.3V -5V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - indicator digital switching output - PCB measurements: 3 x 1.5 cm - Probe measurements: 6 x 3 cm Code S0021 Available Price €1.95
SparkFun micro:climate kit for micro:bit - v3.0 The SparkFun micro:Climate kit is a complete weather station kit that builds on the weather:bit carrier board with weather and soil moisture sensors, all powered by the micro:bit. board. Code SP073 Last items in stock Price €179.00
SONOFF MS01- Smart Soil Moisture Sensor MS01 works with SONOFF TH10/16 to accurately measure soil moisture and send data to your mobile phone. MS01 can regularly water and check soil moisture anytime and anywhere to make your flowers grow healthier. This is an accessory used in SONOFF TH10 / TH16. Code WS044 Available Price €14.90
Tuya Smart ZigBee 3.0 Ethernet Gateway - Control unit: The local Zigbee gateway for your Tuya Zigbee devices provides high-speed local Ethernet + Zigbee Mesh connectivity, increased automation possibilities, local memory for parameters and devices. Code WT007 ✗ Out-of-Stock Price €28.90
Solar Power Manager 5V The solar power management module with the CN3065 chip is ideal for IoT (Internet of Things) projects with renewable energy. Compared to the previous version of the module, improvements have been made to the energy management of the connected battery. Code DF025 Last items in stock Regular price €17.50 -€4.00 Price €13.50
SONOFF SNZB-02 - ZigBee Temperature And Humidity Sensor SONOFF SNZB-02 is an elegant mini wireless intelligent temperature and humidity sensor via ZigBee, through its Bridge(required). Program and create scenes based on the detected values. Maintain a stable temperature in your home. Code WS039 Available Price €9.90
DHT22/AM2302 Temperature Humidity Sensor The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree. DHT22/AM2302 Temperature Humidity Sensor features: - Voltage Operating: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Code S0018 Available Price €6.99
DHT22/AM2302 Temperature Sensor Humidity PCB + Digital Cable for Arduino - The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree Characteristic: - Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: Write texts on the OLED 0.96 '' screen - Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen Send /> Code M0099 Available Regular price €6.49 -€1.00 Price €5.49
SparkFun Weather Meter Kit The SparkFun weather meter kit is a set of basic mechanical components for building a weather station. This kit represents the three basic elements of weather measurement: wind speed, wind direction and precipitation. Whether you are a farmer, a professional meteorologist or a weather enthusiast, building your own weather station can be a truly rewarding project. However, when it comes to measuring the weather, you need some pretty specialised sensors. Code SP090 Backorder Price €109.90
Solar Power Management Module, for 6V~24V Solar Panel The solar power management module is designed for 6V~24V solar panel. It can charge Li 3.7V battery through solar panel or USB connection, and provides 5V/1A regulated output. Code WV002 Available Price €12.95
Sensor Module Moisture Earth Water Soil The module has two outputs: analog A0 and digital D0 Digital output D0 - signal 0 appears or 1 depending on the threshold setting The threshold is set with the potentiometer The sensor can be used for example: Automatic watering for potted plants With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants Characteristic: Operation: 3.3V -5V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - indicator digital switching output - PCB measurements: 3 x 1.5 cm - Probe measurements: 6 x 3 cm Code S0021 Available Price €1.95
SparkFun micro:climate kit for micro:bit - v3.0 The SparkFun micro:Climate kit is a complete weather station kit that builds on the weather:bit carrier board with weather and soil moisture sensors, all powered by the micro:bit. board. Code SP073 Last items in stock Price €179.00
SONOFF MS01- Smart Soil Moisture Sensor MS01 works with SONOFF TH10/16 to accurately measure soil moisture and send data to your mobile phone. MS01 can regularly water and check soil moisture anytime and anywhere to make your flowers grow healthier. This is an accessory used in SONOFF TH10 / TH16. Code WS044 Available Price €14.90
Tuya Smart ZigBee 3.0 Ethernet Gateway - Control unit: The local Zigbee gateway for your Tuya Zigbee devices provides high-speed local Ethernet + Zigbee Mesh connectivity, increased automation possibilities, local memory for parameters and devices. Code WT007 ✗ Out-of-Stock Price €28.90
Solar Power Manager 5V The solar power management module with the CN3065 chip is ideal for IoT (Internet of Things) projects with renewable energy. Compared to the previous version of the module, improvements have been made to the energy management of the connected battery. Code DF025 Last items in stock Regular price €17.50 -€4.00 Price €13.50
SONOFF SNZB-02 - ZigBee Temperature And Humidity Sensor SONOFF SNZB-02 is an elegant mini wireless intelligent temperature and humidity sensor via ZigBee, through its Bridge(required). Program and create scenes based on the detected values. Maintain a stable temperature in your home. Code WS039 Available Price €9.90
DHT22/AM2302 Temperature Humidity Sensor The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree. DHT22/AM2302 Temperature Humidity Sensor features: - Voltage Operating: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Code S0018 Available Price €6.99
DHT22/AM2302 Temperature Sensor Humidity PCB + Digital Cable for Arduino - The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree Characteristic: - Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: Write texts on the OLED 0.96 '' screen - Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen Send /> Code M0099 Available Regular price €6.49 -€1.00 Price €5.49
SparkFun Weather Meter Kit The SparkFun weather meter kit is a set of basic mechanical components for building a weather station. This kit represents the three basic elements of weather measurement: wind speed, wind direction and precipitation. Whether you are a farmer, a professional meteorologist or a weather enthusiast, building your own weather station can be a truly rewarding project. However, when it comes to measuring the weather, you need some pretty specialised sensors. Code SP090 Backorder Price €109.90