Screw Shield V1 for Arduino UNO y MEGA

LCD TFT Shield Adapter 2.4" Touch 3V Expansion Board R3 features:
- Shield LCD TFT 2.4 "Touch 3V expansion board for Uno R3
- Facilitates connections between the TFT LCD 2.4 "Touch 3V with SD card reader and the Arduino UNO board
- Put the screen on the shield and you can connect it directly to the Arduino UNO
- UNO R3 2.4 "TFT LCD shield TFT LCD PCB Adapter for Arduino UNO STM32
- The TFT01 LCD screen operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top
- The TFT LCD PCB adapter for UNO is compatible with the Arduino pins, the user can plug directly the TFT LCD PCB adapter into the shield and placed on the Arduino board. - Can be used with a UNO and LCD screen

This module, which uses the exclusive L298P chip for driving high-power motors, can directly control two DC motors, with a drive current up to 2A. The motor output uses eight-speed Schottky diodes as protection.
The design of the letter allows you to connect directly to the Arduino UNO R3 for easier use. Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM features:
- 1 logical step of the input voltage VD: 5 VDC
- Control of the input voltage VS and control by pulse width modulation:
      - VIN input: 6 - 12 VDC
      - PWRIN input: 4.8 - 35 VDC
- Logic current flow: Iss <36m A
- Operation current management: Io <2 A
- Maximum power dissipation 25W (T = 75 ° C)
- Input of the control signal:

Arduino Shield Sensor Expansion Board V2.0 features:
The Mega Sensor Shield V2.0 allows: - To be directly punched to an Arduino Uno, Mega, Leonardo board
- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more
- Size: 100x54x12 mm

ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino Mega2560 V3.0 features:
- To mount your projects in a comfortable and orderly way, access to all the pins of Arduino Mega2560, it has a universal plate and protoboard zone, 5V and Gnd buses, reset pushbutton, pushbutton and 2 general purpose leds, zones for integrated Soic and Dip
- The seamless mini breadboard has 170 connection points.
- You can stick on the shield with its self-adhesive back.

This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads.

It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 50mm long

Feature of 3D Zum shield: - Input voltage 8-16 V
- 2 connectors for stepper motors
- 4 connectors for laser
- Analog connectors for LDR sensors
- Power jack connector
- Reset button
- Protection fuse for stepper motors
- Compatible with Arduino UNO
- Dimensions of PCB 67 x 54 mm
- Content:
       - 1x Zum Shield 3D
       - 1x UNO R3 Compatible Arduino
       - 1x Controller A4988
       - 1x Male pin strip
       - 1x Heatsink for A4988
       - 1x USB cable
       - Jumpers

The Portenta Breakout module extends the capabilities of the Arduino Portenta module with additional connectors and cables. The module includes a power switch, a DIP switch for selecting the start mode of the Arduino Portenta, as well as a series of connectors: USB A, RJ5, microSD, OpenMW, MIPI 20T JTAG. The board also includes the RTC chip, as well as a slot for the CR2032 battery, a screw connector for the power supply and all the cables for the Arduino Portenta module.

Nicla Sense ME is the smallest Arduino-developed board equipped with a range of the latest Bosch environmental and motion sensors. The module is based on the nRF52832 ARM Cortex M4 chip clocked at 64 MHz with 512 kB of Flash, 64 kB of RAM and 2 MB of SPI Flash and 2 MB of QSPI embedded memory. The Nicla Sense ME features the Bosch BHI260AP, BMP390, BMM150 and BME688 embedded sensors.