Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V features: - Voltage Drop Module - Use a multimeter to check the output voltage and adjust the potentiometer - Small size: 17mm x 11mm - Input voltage: 4.75-23V - Output voltage: 1.0-17V - Current output: 1.8A (peak max. 3A) - Operating temperature: -40 to + 85 ºC - Operating frequency: 240kHz - Conversion efficiency: up to 96% - Output ripple: 30mV (no-load) - Voltage regulation: ± 2.5% Code A0024 Available Price €2.49
Female DC Power Connector Jack 2.1x5.5mm Jack connectors 2.1mm inside and 5.5mm outside to power devices such as LED strips, CCTV (Cameras), Arduino. Female DC Power Connector Jack 2.1x5.5mm features: - Ideal for connecting without welding- It has two screws in the tip for positive and negative cable screwdriver Code K0050 Available Price €0.49
3A DC Converter 4-53V Adjustable LM2596H Step Down Source Wide range of voltages, improved version. Drop module. They will use a multimeter to Check the output voltage and adjust the potentiometer. 3A DC Converter 4-53V Adjustable LM2596H Step Down Source features: - Based on the LM2596HVS-ADJ regulator - Rectification: Asynchronous - Output Voltage: 3v ~ 40v DC (adjustable) - Input Voltage: 4.5v - 53v DC - Max Output Current: 3A (with heat sink) - Ripple in output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2,5% - Operating temperature: -40ºC to + 85ºC - Measurements: 43x 21x 14 mm Code A0018 Available Price €2.79
Mosfet 24V 5A IRF520 PWM controller Mosfet 24V 5A IRF520 PWM controller features: - The IRF520 controller module can control the PWM signal from the Arduino module and adjust the DC voltage of So that we can control the speed of the DC motor, the brightness of the bulb, the LEDs, the heater. - The built-in IRF520 N-MOSFET transistor - Operating voltage: 3.3V -5V ( compatible with ARDUINO Raspberry PI) - Charging voltage: 0-24V - Charging current: up to 5A (more than 1A, the system must be equipped with a heat sink point) - 60W max power (more than 10W must be equipped with a heat sink) - Terminalblock connectors - LED indicating the presence of power - Dimensions: 33x24mm Code A0022 Available Regular price €2.49 -€0.50 Price €1.99
Resistor 100K Ohm 5% 0,25W 1/4W Resistor 100K Ohm 5% 0,25W 1/4W features: 100K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0026 Available Price €0.08
Peltier Ceramic Cell TEC1 12706 12V 60W Peltier Ceramic Cell TEC1 12706 12V 60W features: - Max Power: 60w - Voltage: 12v - Max Voltage: 15,2v - Max Current: 6A - Temperature Variation: - Peltier effect cell model TEC1-12706, 12v, max 60w and 6A, with a temperature difference between their faces of up to 67ºC Code M0055 Available Price €3.95
ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino UNO V5.0 ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino UNO V5.0 features: - To mount your projects in a comfortable and orderly way, access to all the pins of Arduino Uno R3, it has a universal plate and protoboard zone, 5V and Gnd buses, reset pushbutton, pushbutton and 2 general purpose leds, zones for integrated Soic and Dip- The seamless mini breadboard has 170 connection points.- You can stick on the shield with its self-adhesive back. Code M0016 Available Regular price €2.20 -€0.21 Price €1.99
Resistor 200R Ohm 5% 0,25W 1/4W Resistor 200R Ohm 5% 0,25W 1/4W features:-200R Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0007 Available Price €0.08
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo. Control of voltage and current.Use a multimeter to check the output voltage and adjust the potentiometer. Code A0132 Available Price €3.49
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Available Price €3.99
DC Step Down Converter 3.3V 2A 3.4-6V DC Step Down Converter 3.3V 2A 3.4-6V features: - Voltage drop module- Input voltage: 3.4-6V- Output voltage: 3.3V- Current output: adjustable, max 2A- Operating temperature: -40 to + 85 ºC- Operating frequency: 1.5MHz- Efficiency conversion: up to 95%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 12 x 15 mm- Full charge output ripple: Vpp <50 mV- Output accuracy: ± 0.1V- Current IQ without load: 0.2mA- Stop current (EN) <10uA Code A0068 Available Price €3.38
Converter DC USB Step Down 7V-24V to 5V 3A Converter DC USB Step Down 7V-24V to 5V 3A features:- Voltage reduction module with USB connector- DIY mobile power supply, to achieve the 5v output to charge the phone, mp3, mp4, psp, etc. can not charge for the ipad- The USB output converter module has short circuit protection 5A current automatic protection- Based on the monolithic MP2307 controller- Rectification: not synchronous- Input voltage: DC 7v to 24v- Output voltage: DC 5v- Output current: 3A (Little time 4A)- Output connection: USB Type A female connector- Input connection: Terminal with screws- Efficiency of transformation: 96%- Switching frequency: 340KHz- Output ripple: 30mV (max.)- Load regulation: ± 0.5% Code A0016 Available Price €3.99
8A DC Downstream Converter 8-40V to 1.25-35V Current Control XL4016 A high-performance regulator-booster. 24V battery charger - DC / CV method. Power supply of the laptop from a 12V car battery. A high-performance dimmer-regulator. Charger for Li-Ion, Li-Po batteries etc. - CC / CV method. LED Constant current driver for LED diodes. Characteristic: - Input voltage: 6V -40V - Output voltage: 1.25-35V (adjustable) - Output current: 8A, (10A maximum) - Output power: 300W maximum - Efficiency of Conversion: up to 95% - Wiring: Solderless terminal - Operating frequency: 300kHz - Ambient temperature exceeds 40 ° C, increase heat dissipation - LED indicator two-color; - Charge red - Fully charged light green - No charge green Code A0011 Last items in stock Price €7.95
XL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 Descripción:Chip XL4015 - Upgrade of the LM2596Drop moduleUse a multimeter to check the output voltage and adjust the potentiometerVoltage controlXL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 features:- Input voltage: 4.5V-38V- Output voltage: 1.25-36.5V- Current output: 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0012 Available Price €4.95
AMS1117 Buck fixed output module 3.3V 800mA AMS1117 Buck fixed output module 3.3V 800mA features: - Based on AMS1117-3.3V regulator - Input Voltage: 4.5 - 12Vdc - Output Voltage: 3.3 Vdc (+/- 0,05V) - Max.output current: 800mA - Operating temperature: -40ºC to + 150ºC - Dimensions: 25mm x 12mm Code A0023 Available Price €1.49
Boost Buck Step Up-Down Automatic Converter Descripción:This is a powerful, efficient step-up (boost) and step-down (buck) switching voltage converter. It will automatically change between boosting and bucking to maintain a stable output voltage, regardless of the input.The output is set with a multi-turn potentiometer.Boost Buck Step Up-Down Automatic Converter features:- IC Chip: LM2577S-ADJ and LM2596S-ADJ - Module Properties: non-isolated Boost Buck constant current, constant voltage module (CC CV) charging module- Scope: High-power constant current LED driver.- Battery charger (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charger, solar panels, wind generators. Code A0017 Available Price €9.49
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of voltage and current.DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo features:- Input voltage: 4-38V- Output voltage: 1.25-36V- Current output: adjustable, 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 26mm x 14mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0014 Available Price €3.49
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.99
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo. Control of voltage and current.Use a multimeter to check the output voltage and adjust the potentiometer. Code A0132 Available Price €3.49
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Available Price €3.99
DC Step Down Converter 3.3V 2A 3.4-6V DC Step Down Converter 3.3V 2A 3.4-6V features: - Voltage drop module- Input voltage: 3.4-6V- Output voltage: 3.3V- Current output: adjustable, max 2A- Operating temperature: -40 to + 85 ºC- Operating frequency: 1.5MHz- Efficiency conversion: up to 95%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 12 x 15 mm- Full charge output ripple: Vpp <50 mV- Output accuracy: ± 0.1V- Current IQ without load: 0.2mA- Stop current (EN) <10uA Code A0068 Available Price €3.38
Converter DC USB Step Down 7V-24V to 5V 3A Converter DC USB Step Down 7V-24V to 5V 3A features:- Voltage reduction module with USB connector- DIY mobile power supply, to achieve the 5v output to charge the phone, mp3, mp4, psp, etc. can not charge for the ipad- The USB output converter module has short circuit protection 5A current automatic protection- Based on the monolithic MP2307 controller- Rectification: not synchronous- Input voltage: DC 7v to 24v- Output voltage: DC 5v- Output current: 3A (Little time 4A)- Output connection: USB Type A female connector- Input connection: Terminal with screws- Efficiency of transformation: 96%- Switching frequency: 340KHz- Output ripple: 30mV (max.)- Load regulation: ± 0.5% Code A0016 Available Price €3.99
8A DC Downstream Converter 8-40V to 1.25-35V Current Control XL4016 A high-performance regulator-booster. 24V battery charger - DC / CV method. Power supply of the laptop from a 12V car battery. A high-performance dimmer-regulator. Charger for Li-Ion, Li-Po batteries etc. - CC / CV method. LED Constant current driver for LED diodes. Characteristic: - Input voltage: 6V -40V - Output voltage: 1.25-35V (adjustable) - Output current: 8A, (10A maximum) - Output power: 300W maximum - Efficiency of Conversion: up to 95% - Wiring: Solderless terminal - Operating frequency: 300kHz - Ambient temperature exceeds 40 ° C, increase heat dissipation - LED indicator two-color; - Charge red - Fully charged light green - No charge green Code A0011 Last items in stock Price €7.95
XL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 Descripción:Chip XL4015 - Upgrade of the LM2596Drop moduleUse a multimeter to check the output voltage and adjust the potentiometerVoltage controlXL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 features:- Input voltage: 4.5V-38V- Output voltage: 1.25-36.5V- Current output: 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0012 Available Price €4.95
AMS1117 Buck fixed output module 3.3V 800mA AMS1117 Buck fixed output module 3.3V 800mA features: - Based on AMS1117-3.3V regulator - Input Voltage: 4.5 - 12Vdc - Output Voltage: 3.3 Vdc (+/- 0,05V) - Max.output current: 800mA - Operating temperature: -40ºC to + 150ºC - Dimensions: 25mm x 12mm Code A0023 Available Price €1.49
Boost Buck Step Up-Down Automatic Converter Descripción:This is a powerful, efficient step-up (boost) and step-down (buck) switching voltage converter. It will automatically change between boosting and bucking to maintain a stable output voltage, regardless of the input.The output is set with a multi-turn potentiometer.Boost Buck Step Up-Down Automatic Converter features:- IC Chip: LM2577S-ADJ and LM2596S-ADJ - Module Properties: non-isolated Boost Buck constant current, constant voltage module (CC CV) charging module- Scope: High-power constant current LED driver.- Battery charger (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charger, solar panels, wind generators. Code A0017 Available Price €9.49
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of voltage and current.DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo features:- Input voltage: 4-38V- Output voltage: 1.25-36V- Current output: adjustable, 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 26mm x 14mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0014 Available Price €3.49
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.99