Peltier Ceramic Cell TEC1 12706 12V 60W

ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino UNO V5.0 features:
- To mount your projects in a comfortable and orderly way, access to all the pins of Arduino Uno R3, it has a universal plate and protoboard zone, 5V and Gnd buses, reset pushbutton, pushbutton and 2 general purpose leds, zones for integrated Soic and Dip
- The seamless mini breadboard has 170 connection points.
- You can stick on the shield with its self-adhesive back.

15x Electrolytic Capacitor 22uF 25V 105ºC PIC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 22uF
-Maximum tension: 25V
-Maximum temperature: 105º C
-Dimensions: 5x11mm
-Quantity: 15 units

The module has two outputs: analog A0 and digital D0.
digital output D0 - signal 0 or 1 appears depending on the configuration of threshold.
The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - digital switching output indicator
- Measurements PCB: 3 x 1.5 cm
- Sensor measurements: 5.4 x 3.9 cm

Descent module.
Use a multimeter to check the output voltage and adjust the potentiometer.
Control of tension.
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:
- Input voltage: 4.5-38V
- Output voltage: 1.25-36.5V
- Current output: 2A (max 3A with heat sink)
- Operating temperature: -40 to + 85 ºC
- Operating frequency: 150KHz
- Efficiency conversion: up to 92%
- Load Regulation: +/- 0.5%
- Voltage Regulation: +/- 2.5%
- Protection over temperature: the output switches off automatically
- Size: 62mm x 38mm x 15mm
Principal functions:
- Step-down converter with overcurrent protection
- Voltmeter up to 40V, remember to set the input voltage to 4.5V

Ideal to power your Arduino board through the power input.
5x 9v Battery Adapter Connector 6F22 with Cable features:

- Cable 15cm long
- Battery connector 9V, 6F22

Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features:
> - Input voltage 2.5V-3V
- Operating power 60mW / 15fps VGA YUV
- Resolution VGA 640x480 pixels (30fps)
- Maximum frame rate 30fps VGA
- Flicker 50Hz / 60Hz automatic detection
- Lens size 1/6 "
- Angle of view 25 °
- Sensitivity 1.3V / (lux- seg)
- SCCB (Serial Camera Control Bus) interface
- Output format · 8 Bits
- YUV / YCbCr 4: 2: 2
- RGB 565/555/444
- GRB 4: 2: 2
- RAW RGB data
- High sensitivity Light operation
- Automatic adjustment
- Color level saturation - Edge enhancement
- Noise level

Load cell Load Cell 20kg features:
- Load range: 20kg
- Operating voltage: 3VDC ~ 14 VDC
- Nominal output: 1.0 ± 0.15mV / V
- Repeatability: 0.03% FS
- Effect of the temperature at the outlet: 0.01% F.S /°C
- Effect of temperature on zero: 0.05% F.S /°C
- Zero: ± 0.1000 mV / V
- Input impedance: 1115 + -10% Ω
- Output impedance: 1000 + - 10% Ω
- Insulation resistance:> = 1000 MΩ
- Safe Overload Rate: 150% FS
- Final overload rate: 200% FS
- Temperature range: -20 - 60 °C
- Material: Aluminum alloy
- Degree of protection: IP65
- Cable length: 25 cm
- Size: 75 x 12.7 x 12.7 mm
- Wiring:
* Red: Feeding +
* Black: Source -
* Green: Sign +
* White: Signal -