40x Male to male cables 20cm Characteristic: -Length: 20cm -Quantity: 40 cables -Mono Dupont connectors on both ends -Compatible with 2.54mm female connectors -High quality and good working condition -Easy to install and use Code K0006 Available Price €2.06
Full adhesive insulating base with hole for 2x18650 - pack 5unds Pre-cut insulating base for electrode, base with holes for 2x 18650 batteries. Self-adhesive pad isolates and protects battery contacts from short circuits. Stick to the battery after sealing it in a package. If the connecting tape becomes hot, insulation protects the battery against damage to the casing and against short circuits. Code PP079 Available Price €0.49
Breadboard Power Supply Protoboard 830/400 Points MB102 Ideal for your electronic projects, arduino, but can also be used with other microcontrollers. Breadboard Power Supply Protoboard 830/400 Points MB102 features:- Input voltage supports up to 12V- Selectable 3.3V or 5V- USB input or standard DC 2.1 x5.5mm connector- Maximum current 700mA- It fits perfectly on the MB-102 breadboard feeding the two lateral buses- Weight: 15 gr. (approx.) Compatible only with MB-102 type plates Code A0003 Available Price €1.61
Battery charger BMS 3,7-96V 10A - Automatic charge controller module This 3.7-96V 10A battery charger is an automatic charge controller module that prevents the battery from dropping below a voltage level, the value of which is adjustable. It is suitable for 1.5 to 120V batteries, as using it will save time and energy. Code A0130 Available Price €9.01
USB Cable for Arduino Type A-B USB Cable for Arduino Type A-B features: - Length: 50cm- Color: Blue Code K0158 Available Price €1.23
HC-SR04 Ultrasonic Sensor Distance Measuring Module It is very easy to make it work with an Arduino, PIC or any other microcontroller. In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle. HC-SR04 Ultrasonic Sensor Distance Measuring Module features: - Supply voltage: 5V (4.5V- 6V) - Consumption: 30 mA typical, (35 mA max) - Interface: VCC , GND, Signal - Range: 2 cm to 3 meters - Angle 15º - LED indicator of measurement in progress - Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm - Quantity: 1 unit Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry: Automatic robot operation with obstacle detection /> Code S0007 Last items in stock Price €1.48
Bluetooth Transceiver Module HC-05 Wireless - HC-05 Bluetooth transceiver module with base- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.Bluetooth Transceiver Module HC-05 Wireless features:- Chipset CSR BC417- 3.6 to 6 Vdc power supply- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps Code W0004 Available Price €4.45
Resistor 10K Ohm 5% 0,25W 1/4W Resistor 10K Ohm 5% 0,25W 1/4W features:-10K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0021 Available Price €0.07
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.64
Converter DC USB Step Down 7V-24V to 5V 3A Converter DC USB Step Down 7V-24V to 5V 3A features:- Voltage reduction module with USB connector- DIY mobile power supply, to achieve the 5v output to charge the phone, mp3, mp4, psp, etc. can not charge for the ipad- The USB output converter module has short circuit protection 5A current automatic protection- Based on the monolithic MP2307 controller- Rectification: not synchronous- Input voltage: DC 7v to 24v- Output voltage: DC 5v- Output current: 3A (Little time 4A)- Output connection: USB Type A female connector- Input connection: Terminal with screws- Efficiency of transformation: 96%- Switching frequency: 340KHz- Output ripple: 30mV (max.)- Load regulation: ± 0.5% Code A0016 Available Price €3.30
XL4015 DC-DC 5A Digital Step-down LED Converter with Voltmeter, Ammeter and USB Output This Step-down voltage converter includes 5 functions in one module. It can be used as a voltmeter, ammeter and measurements can be recovered through its USB port. The output voltage and voltage can be adjusted thanks to two potentiometers present in the module. It has an efficiency Very high, it has a display screen for voltage, current and two buttons to configure what you want to see. Characteristic: - Voltage of input: 5.5 - 36 V - Output voltage: 1.25-32 V continuously adjustable - Output current: 4.5 A (Max 5A for a short time) adjustable with potentiometer, - Power output: 75 W maximum (recommended to use 50 W, large pressure difference, please reduce power) - Operating temperature: -40 ° C - + 150 ° C Code A0077 Available Regular price €6.52 -€1.00 Price €5.52
AMS1117 Buck fixed output module 3.3V 800mA AMS1117 Buck fixed output module 3.3V 800mA features: - Based on AMS1117-3.3V regulator - Input Voltage: 4.5 - 12Vdc - Output Voltage: 3.3 Vdc (+/- 0,05V) - Max.output current: 800mA - Operating temperature: -40ºC to + 150ºC - Dimensions: 25mm x 12mm Code A0023 Available Price €1.23
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo. Control of voltage and current.Use a multimeter to check the output voltage and adjust the potentiometer. Code A0132 Available Price €2.88
Converter module AMS1117 Buck fixed output 5V 800mA This module is a voltage regulator that creates an output voltage of 5V with a maximum current of 800mA. The integrated regulator is referenced AMS1117. The module has two two point connectors for quick connection. Converter module AMS1117 Buck fixed output 5V 800mA features: - Based on the regulator AMS1117-5V - Input voltage: 4.5-12VDC - Output voltage: 5VDC (+/- 0.05V) - Max output current: 800mA - Operating temperature: -40C to + 150C - PCB size: 25x12 mm Code A0073 Available Price €1.23
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Available Price €3.30
DC Step Down Converter 3.3V 2A 3.4-6V DC Step Down Converter 3.3V 2A 3.4-6V features: - Voltage drop module- Input voltage: 3.4-6V- Output voltage: 3.3V- Current output: adjustable, max 2A- Operating temperature: -40 to + 85 ºC- Operating frequency: 1.5MHz- Efficiency conversion: up to 95%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 12 x 15 mm- Full charge output ripple: Vpp <50 mV- Output accuracy: ± 0.1V- Current IQ without load: 0.2mA- Stop current (EN) <10uA Code A0068 Available Price €2.79
8A DC Downstream Converter 8-40V to 1.25-35V Current Control XL4016 A high-performance regulator-booster. 24V battery charger - DC / CV method. Power supply of the laptop from a 12V car battery. A high-performance dimmer-regulator. Charger for Li-Ion, Li-Po batteries etc. - CC / CV method. LED Constant current driver for LED diodes. Characteristic: - Input voltage: 6V -40V - Output voltage: 1.25-35V (adjustable) - Output current: 8A, (10A maximum) - Output power: 300W maximum - Efficiency of Conversion: up to 95% - Wiring: Solderless terminal - Operating frequency: 300kHz - Ambient temperature exceeds 40 ° C, increase heat dissipation - LED indicator two-color; - Charge red - Fully charged light green - No charge green Code A0011 Available Price €6.57
Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down features:- Based on the MP1584EN regulator- Output Voltage: 1.6V - 26V DC (adjustable)- Input Voltage: 4.5V - 28V DC- Max. Output Current: 3A (with heat sink)- Frequency: 1MHz- Conversion Efficiency (1A): 94%- Short circuit protection- Protection against overheating- Operating temperature: -40ºC to + 85ºC- Measures 22 x 17 x 4 mm Code A0007 Available Price €1.61
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.64
Converter DC USB Step Down 7V-24V to 5V 3A Converter DC USB Step Down 7V-24V to 5V 3A features:- Voltage reduction module with USB connector- DIY mobile power supply, to achieve the 5v output to charge the phone, mp3, mp4, psp, etc. can not charge for the ipad- The USB output converter module has short circuit protection 5A current automatic protection- Based on the monolithic MP2307 controller- Rectification: not synchronous- Input voltage: DC 7v to 24v- Output voltage: DC 5v- Output current: 3A (Little time 4A)- Output connection: USB Type A female connector- Input connection: Terminal with screws- Efficiency of transformation: 96%- Switching frequency: 340KHz- Output ripple: 30mV (max.)- Load regulation: ± 0.5% Code A0016 Available Price €3.30
XL4015 DC-DC 5A Digital Step-down LED Converter with Voltmeter, Ammeter and USB Output This Step-down voltage converter includes 5 functions in one module. It can be used as a voltmeter, ammeter and measurements can be recovered through its USB port. The output voltage and voltage can be adjusted thanks to two potentiometers present in the module. It has an efficiency Very high, it has a display screen for voltage, current and two buttons to configure what you want to see. Characteristic: - Voltage of input: 5.5 - 36 V - Output voltage: 1.25-32 V continuously adjustable - Output current: 4.5 A (Max 5A for a short time) adjustable with potentiometer, - Power output: 75 W maximum (recommended to use 50 W, large pressure difference, please reduce power) - Operating temperature: -40 ° C - + 150 ° C Code A0077 Available Regular price €6.52 -€1.00 Price €5.52
AMS1117 Buck fixed output module 3.3V 800mA AMS1117 Buck fixed output module 3.3V 800mA features: - Based on AMS1117-3.3V regulator - Input Voltage: 4.5 - 12Vdc - Output Voltage: 3.3 Vdc (+/- 0,05V) - Max.output current: 800mA - Operating temperature: -40ºC to + 150ºC - Dimensions: 25mm x 12mm Code A0023 Available Price €1.23
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo. Control of voltage and current.Use a multimeter to check the output voltage and adjust the potentiometer. Code A0132 Available Price €2.88
Converter module AMS1117 Buck fixed output 5V 800mA This module is a voltage regulator that creates an output voltage of 5V with a maximum current of 800mA. The integrated regulator is referenced AMS1117. The module has two two point connectors for quick connection. Converter module AMS1117 Buck fixed output 5V 800mA features: - Based on the regulator AMS1117-5V - Input voltage: 4.5-12VDC - Output voltage: 5VDC (+/- 0.05V) - Max output current: 800mA - Operating temperature: -40C to + 150C - PCB size: 25x12 mm Code A0073 Available Price €1.23
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Available Price €3.30
DC Step Down Converter 3.3V 2A 3.4-6V DC Step Down Converter 3.3V 2A 3.4-6V features: - Voltage drop module- Input voltage: 3.4-6V- Output voltage: 3.3V- Current output: adjustable, max 2A- Operating temperature: -40 to + 85 ºC- Operating frequency: 1.5MHz- Efficiency conversion: up to 95%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 12 x 15 mm- Full charge output ripple: Vpp <50 mV- Output accuracy: ± 0.1V- Current IQ without load: 0.2mA- Stop current (EN) <10uA Code A0068 Available Price €2.79
8A DC Downstream Converter 8-40V to 1.25-35V Current Control XL4016 A high-performance regulator-booster. 24V battery charger - DC / CV method. Power supply of the laptop from a 12V car battery. A high-performance dimmer-regulator. Charger for Li-Ion, Li-Po batteries etc. - CC / CV method. LED Constant current driver for LED diodes. Characteristic: - Input voltage: 6V -40V - Output voltage: 1.25-35V (adjustable) - Output current: 8A, (10A maximum) - Output power: 300W maximum - Efficiency of Conversion: up to 95% - Wiring: Solderless terminal - Operating frequency: 300kHz - Ambient temperature exceeds 40 ° C, increase heat dissipation - LED indicator two-color; - Charge red - Fully charged light green - No charge green Code A0011 Available Price €6.57
Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down features:- Based on the MP1584EN regulator- Output Voltage: 1.6V - 26V DC (adjustable)- Input Voltage: 4.5V - 28V DC- Max. Output Current: 3A (with heat sink)- Frequency: 1MHz- Conversion Efficiency (1A): 94%- Short circuit protection- Protection against overheating- Operating temperature: -40ºC to + 85ºC- Measures 22 x 17 x 4 mm Code A0007 Available Price €1.61