Shield for Arduino Mega2560

Wheels for 360 degree continuous rotation servo motors type SG90, FS90R, SG92r. The wheels have silicone tyres and measure 60 mm (2.36″) in diameter. Four additional mounting holes for 4-40 bolts allow the wheel to be used with several of our universal mounting bracket.

MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features:
- Booster module
- The output voltage may be greater than the input voltage
- Use a multimeter to check the output voltage and adjust the potentiometer
- Input voltage: 2-24V
- Output voltage: 5-28V
- Current output: 2A - Operating temperature: -40ºC to + 85ºC
- Conversion efficiency: up to 93%
- Size: 17.5 x 30 mm

It has an Atmel SAM3X8E ARM Cortex-M3 chip running at 84Mhz with a factory-loaded bootloader with 54 digital input / output (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UART (hardware serial ports).
The board includes a USB connector, a SPI port, a reset button, a button erase and some status LEDs.
Atmega16U2 programmed as a USB / Serial converter for power, simply connect it to a computer with a USB cable or power with a power adapter and DC connector.
Characteristic:
Operating voltage: 3.3V
Input voltage (recommended): 7-12V
Digital I / O Pins: 54 (12 PWM outputs)
Analog input 12 pins
2 x DAC
2 x TWI
4x UART
DC current per DIGITAL I / O pin 130 mA
Flash: 512 KB

The display is compatible with the PCD8544 controller.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32 . Characteristic: - LCD screen, 48x84 pixels
- Vcc supply 2.7-3.3V
- Voltage LED backlight 2.7-3.2V
- Compatible PCD8544 controller
- SPI interface
- PCB dimensions (mm): 45x45
- Includes solder pins
- The screen may have small stripes

Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +.
AL422B Video buffer consists of 3M-bits of DRAM, and it is configured as 393.216 x 8 bit FIFO (First In First Out). The interface is very easy to use because all operations are controlled by the internal DRAM memory controller. VGA Camera 640x480 FIFO AL422 Buffer OV7670 30fps features:
- Input voltage: 2.5V-3V
- Controller: AL422B FIFO buffer
- Operating power: 60mW / 15fps VGA YUV
- VGA resolution: 640x480 pixels (30fps),
- Maximum frame rate: 30fps VGA
- Flicker: 50Hz / 60Hz auto detection
- Lens size: 1/6 "
- Angle of view: 25 ° - Sensitivity: 1.3V / (lux- sec)
- SCCB (Serial Camera Control Bus) interface
- Output format: 8 Bits
- YUV />

This switch can be used for development projects and for the industry. All metal parts are not oxidized, the insulation material is of high quality.
Its pins protected by an anti oxidant makes welding much easier. Switch On/On 3-pin 6A SPDT features:
- Type: Latch SPDT
- Material: Plastic, metal
- Maximum operating current and voltage: 3A / 250V, 6A / 125V
- Number of pins: 3
- Pin size: 4.5x2 mm
- Type of current: AC/DC
- Pins to be welded
- Switch action: 2 positions On/On
- Size: 13.2x12.7x33.3mm

1.44 inch TFT LCD screen 128x128 SPI features:
- TFT LCD screen 128x128 pixels
- 4-wire SPI interface (A0, SDA, SCK, CS)
- Size: 1.44 inches
- Interface: SPI
- Resolution: 128 * 128
- Visual area: 1: 1 square
- Color screen TFT, the effect is much better than other small CSTN displays
- Disk drive: ST7735
- Fully compatible and alternative 5110 interface
- Onboard LDO, 5V / 3.3 input voltage support V
- Screen dimensions: 30 x 28 mm
- PCB dimensions: 45 x 32 mm

It has an Atmega2560 chip running at 16Mhz with a factory loaded bootloader with 54 digital input / output pins (from which 14 can be used as PWM outputs) and 16 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, an ICSP port, a reset button and some status LEDs. Atmega16U2 programmed as a USB-to-serial converter. Simply connect it to a computer with a USB cable or power with a power adapter and DC connector.