Shield Sensor Expansion Board Arduino compatible V2.0

The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on.

Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid.

Getting started with Arduino? This multi-function shield for Arduino UNO is ideal for your first Arduino DIY projects. It includes 4 7-segment displays, buzzer, 3 push buttons, 4 LEDs, potentiometer and sockets.

The Portenta Breakout module extends the capabilities of the Arduino Portenta module with additional connectors and cables. The module includes a power switch, a DIP switch for selecting the start mode of the Arduino Portenta, as well as a series of connectors: USB A, RJ5, microSD, OpenMW, MIPI 20T JTAG. The board also includes the RTC chip, as well as a slot for the CR2032 battery, a screw connector for the power supply and all the cables for the Arduino Portenta module.

Prototype PCB shield board with screw terminal block for Arduino. A very convenient solution for first experiments with Arduino Mega board. To assemble your projects in a comfortable and tidy way, access to all Arduino Mega2560 pins, universal board area, 5V and Gnd buses, reset button. Shield is supplied assembled.

This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person.

USB Host Shield Google Android ADK UNO Mega 2560 features:
Shield ADK USB allows: - Communication with other USB devices, to build their own mobile accessories
- Create projects that require USB Host functionality
- Supports USB 2.0, Android ADK
- It can also be used with any device equipped with SPI interface
- Compatible with Android devices: v2.3.4 and above
- USB Host with support for HUB protocol

Feature of 3D Zum shield: - Input voltage 8-16 V
- 2 connectors for stepper motors
- 4 connectors for laser
- Analog connectors for LDR sensors
- Power jack connector
- Reset button
- Protection fuse for stepper motors
- Compatible with Arduino UNO
- Dimensions of PCB 67 x 54 mm
- Content:
       - 1x Zum Shield 3D
       - 1x UNO R3 Compatible Arduino
       - 1x Controller A4988
       - 1x Male pin strip
       - 1x Heatsink for A4988
       - 1x USB cable
       - Jumpers

This module, which uses the exclusive L298P chip for driving high-power motors, can directly control two DC motors, with a drive current up to 2A. The motor output uses eight-speed Schottky diodes as protection.
The design of the letter allows you to connect directly to the Arduino UNO R3 for easier use. Module L298P DC 2A Motor Management Shield Bluetooth Interface PWM features:
- 1 logical step of the input voltage VD: 5 VDC
- Control of the input voltage VS and control by pulse width modulation:
      - VIN input: 6 - 12 VDC
      - PWRIN input: 4.8 - 35 VDC
- Logic current flow: Iss <36m A
- Operation current management: Io <2 A
- Maximum power dissipation 25W (T = 75 ° C)
- Input of the control signal:

A remote monitoring and control solution, optimised for outdoor environments. Collect real-time data from smart sensors and leverage everything to the edge, in your smart farm management.